ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:114.95KB ,
资源ID:439968      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-439968.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ARMY A-A-52435 A-2009 HOSE ASSEMBLIES METAL FLEXIBLE FUEL AND OIL [Cancelled ARMY MIL-H-13524 B CANC NOTICE 1 ARMY MIL-H-13524 B ARMY MIL-H-13524 A (2) ARMY MIL-H-13524 A]《燃料和油用弹性金.pdf)为本站会员(bonesoil321)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ARMY A-A-52435 A-2009 HOSE ASSEMBLIES METAL FLEXIBLE FUEL AND OIL [Cancelled ARMY MIL-H-13524 B CANC NOTICE 1 ARMY MIL-H-13524 B ARMY MIL-H-13524 A (2) ARMY MIL-H-13524 A]《燃料和油用弹性金.pdf

1、Comments, suggestions, or questions on this document should be addressed to U.S. Army Tank-automotive and Armaments Command, ATTN: RDTA-EN/STND/TRANS, MS# 268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact information can change, you may

2、want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 4720 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-52435A 3 August 2009 SUPERSEDING A-A-52435 2 April 1993 COMMERCIAL

3、 ITEM DESCRIPTION HOSE ASSEMBLIES, METAL: FLEXIBLE, FUEL AND OIL The General Services Administration has authorized the use of this commercial item description (CID) as a replacement for MIL-H-13524B(AT), which is cancelled. 1. SCOPE. This CID covers two types of flexible hose assemblies for the con

4、veyance of gasoline or oil or for other applications when installed in military vehicles or other U.S. Army equipment with the exception of use with aircraft engine fluid lines. 1.1 Classification. Hose assemblies shall be of the following types as specified (see 5.2): Type I - Corrosion resistant s

5、teel Type II - Bronze or brass 2. SALIENT CHARACTERISTICS 2.1 Materials. Materials used in the hose assemblies shall be as specified herein and in applicable drawings (see 5.2). The use of recovered materials made in compliance with regulatory requirements is acceptable providing all requirements of

6、 this CID are met (see 5.5). 2.2 Design and construction. Hose shall consist of corrugated or convoluted tubing of seamless, welded, or brazed design, protected with a cover of one or more beamed wire braids. Each length of hose shall be fitted with a set of couplings, as specified in applicable dra

7、wings (see 5.2), each permanently attached to hose. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52435A 2 2.3 Dimensions. Hose assemblies shall be of the dimensions specified in procurement documents and in applicable drawings (see 5.2). 2.4 H

8、ose assembly interchangeability. Unless otherwise specified, hose assemblies for each particular size (inside diameter) shall be interchangeable with all other like hose assemblies intended for the same use. 2.5 Performance. 2.5.1 Flexibility and leakage. Hose assemblies shall be capable of being be

9、nt around a mandrel under an internal hydrostatic pressure in accordance with table I while at 300 degrees Fahrenheit (F) 149 degrees Celsius (C). This shall be evidenced by the absence of leaks, deformation, permanent set, or interior obstruction. TABLE I. Mandrel diameters and hydrostatic pressure

10、 for flexibility and leak test. Hose size (inside diameter) Mandrell diameter Hydrostatic pressure inches millimeters inches millimeters pounds per square inch Kilopascals 3/16 1/4 5/16 3/8 1/2 5/8 3/4 1 4.8 6.3 7.9 9.5 12.7 15.9 19.0 25.4 5-1/2 7 8 11 14 18 20 24 139.7 177.8 203.2 279.4 355.6 457.2

11、 508.0 635.0 1830 1470 1160 890 820 750 660 440 12617 10135 7998 6136 5654 5171 4551 3034 2.6 Environmental. 2.6.1 Vibration. The hose assemblies shall show no evidence of leakage after being subjected to 500 hours of vibration, followed by 24 hours of refrigeration at -65F and subsequent flexing th

12、rough 90 degree bends in four directions, followed by an additional 24 hours of vibration. The vibration shall be performed with SAE 30 oil circulating at 300F (149C), 175 pounds per square inch (psi) 1207 Kilopascals (kPa), 116F (47C) ambient air temperature, .052 inch 1.3 millimeters (mm) total di

13、splacement (double amplitude), at 30 cycles per second. Prior to vibration, the sample shall be arranged to provide an initial slack of 3/16 inch (4.8 mm) and an offset of 1-1/2 inches (38.1 mm) at an angle of 90 degrees to the direction of stroke. The vibration may be performed continuously or inte

14、rmittently. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52435A 3 2.6.2 Corrosion resistance. When hose fittings are made of ferrous alloys, either in whole or part, they shall withstand 100 hours of salt spray in accordance with ASTM B117 wit

15、hout showing evidence of damaging corrosion. 2.7 Identification and markings. Identification and markings of the hose assemblies shall be permanent and legible and shall include as a minimum, the manufacturers identification code (CAGE), the engineering drawing part number (see 5.2), and the nationa

16、l stock number (NSN). 2.8 Workmanship. Workmanship shall be such as to produce hose assemblies free from defects such as cracks, cuts, breaks, as well as restricted holes through end fittings, or damaged or burred end fitting threads. 3. QUALITY ASSURANCE PROVISIONS 3.1 Responsibility for inspection

17、. The contractor is responsible for the performance of all inspections (examinations and tests). 3.2 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description and that the

18、 product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4. PRE

19、SERVATION, PACKAGING, PACKING, LABELING, AND MARKING. Preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order (see 5.2). 5. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 5.1 Addre

20、sses for obtaining copies of referenced documents. 5.1.1 Non-Government publications. ASTM B117 “Standard Test Method of Salt Spray (Fog) Testing” is available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Provided by IHSNot for ResaleN

21、o reproduction or networking permitted without license from IHS-,-,-A-A-52435A 4 5.2 Ordering data. Acquisition documents must specify the following: a. Title, number and date of this commercial item description. b. Issue of the DoDISS and industry standards to be cited in the solicitation (see 5.1)

22、. c. Title, number, and revision letter of the applicable engineering drawing (see 2.2). d. Type, size, and length of hose assemblies required (see 1.1, 2.1, and 2.3). e. Engineering drawing part number (see 2.7). f. Selection of applicable level of protection and packaging requirements (see 4.0). 5

23、.3 Cross-reference data. Hose assemblies conforming to this document are interchangeable/ substitutable with hose assemblies conforming to MIL-H-13524B(AT). 5.4 Metric product. Hose assemblies that are to metric dimensions will be considered on the following basis: a. Products manufactured to metric

24、 dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of IEEE-SI10, and all other requirements of this CID are met. b. If a product is manufactured to me

25、tric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. c. The contracting officer has the option of accepting or rejecting the product. 5.5 Regulatory requirements. T

26、he offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Custodian: Preparing Activity: Army - AT Army - AT Review Activities: (Project 4720-2009-019) Army - EA DLA - CC NOTE: The activities listed above were interested in

27、 this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1