ARMY A-A-52493-1994 ROD END THREADED-LINKAGE RIGID《刚性螺纹连杆杆头》.pdf

1、A-A-52493 7979974 OLb422b O03 INCH-POUND A-A- 52 49 3 u SUPERSEDING MS 6 3 04 3 C 20 August 1973 COMMERCIAL ITEM DESCRIPTION ROD END, THREADED-LINKAGE, RIGID The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. i. SCOPE. This

2、CID covers rigid rGd end clevises. The items are intened to be attached to a shaft or rod by pinning to provide a means of fastening or attaching the shaft or rod to another part. 2. SALIENT CHARACTERISTICS. 2.1 Materiais. The material shall be carbon steel, Unified Numbering System (UNS) G10150 thr

3、ough G10290. These steels shall have a minimum ultimate tensile strength of 55,000 pounds per square inch (psi). The use of recovered materials is acceptable providing that all requirements of this CID are met (see note 5.5). 2.2 Design and construction. The design and construction of rod ends shall

4、 be in accordance with figure 1. 2.3 Protective finish. When specified (see 5.2), protective finish shall be zinc coating in accordance with ASTM A123 or ASTM B633-85, type II, class SC3. 2.4 Identification and markings. Identificatiqn and markings shall be permanent and legible and shall consist of

5、 the part identification number (PIN) and the manufactuers identification (see 5.2 and 5.3). 3. QUALITY ASSURANCE PROVISIONS. 3.1 Responsibility for inspection. The contractor is responsible or the performance of all inspections (examinations and tests). r I Beneficial comments, recommendations, add

6、itions, deletions clarifications, etc. and any other data which may improve this document should be sent by letter to: U.S. Army Tank-Automotive Command, ATTN: AMSTA-GDS, Warren, MI 48397-5000. AMSC NIA FSC 5340 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provid

7、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52493 = 9999974 01ib4227 T4T D PIN Number A52493-1 A5 2 4 9 3- 2 AS2493-3 A52 49 3 -4 A-A-52493 “B“ “A“ Thread Thread UNF-2A Length .3125 -. 24 0.937 -375 - 24 1.437 ,500 - 20 1.25 .625 - 18 1.437 25-36 F

8、LUTES STRAIGHT KNURL .635 REFERENCE DIAMETER BEFORE .O31 X 45 Former MS Part Number MS63043-1 MS63043-2 MS63043-3 MS63043-4 Former Army Part Number 8689584 8741801 NONE NONE “C“ Knur 1 Length 1.625 1.125 1.312 1.125 NOTE: 1. Surfaces except hurling shall be free from burrs and sharp edges. 2. Dimens

9、ions are in inches. Unless otherwise specified, tolerances are 2 .O31 on decimals and 15 degrees on angular dimensions. 3. This CIE is noc ictended to limie construction to features otner than as shown herein. Figure 1. Threaded rod end design, configuration and part numbers. 3.2 Contractor certific

10、ation. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description and that the product conforms to the producers own drawings, specifications, workmanship standards, and I quality assurance practice

11、s. Goverment acceptance. such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Item with known defects shall not be submitted for The Government reserves the right to require proof of r 2 Provided by IHSNot for ResaleNo rep

12、roduction or networking permitted without license from IHS-,-,-A-A-52493 m 9999974 0364228 986 m A-A- 52 49 3 4. PRESERVATION, PACKAGING, PACKING, LABELING, AND MARKING. Preservation, packaging, packing, labeling, and marking for the desired level shall be as specified in the contract (see 5.2). 5.

13、NOTES. This Section contains information of a general or explanatory nature that may be helpful but is not mandatory. 5.1 5.1.1 Non-GOVerIUnent publications. Copies of ASTM A123 “Standard Specifications for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products“ and ASTM 633-85 “standard Spec

14、ifications for Electrodeposited Coatings of Zinc on iron and Steel“ are available from the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. Descriptions of UNS steel designations are in the “Metals and Alloys in the Unified Numbering System“ publication. Automoti

15、ve Engineers, Inc., 400 Commonwealth Drive, Warrendale, PA 15096-0001. 5.2 Ordering data. Acquisition documents must specify the following: - Addresses for obtaining copies of referenced documents. Copies of this publication are available from the Society of a. Title, number, and date of this CID. b

16、. Issue of DODISS to be cited in the solicitatian, and if required, the c. PIN number and quantity required (see 2.4 and 5.3). d. Protective finish, if required (see 2.3). e. Selection of applicable level and packaging requirements (see 4). specific issue of individual documents referenced. 5.3 Part

17、 or identification number (PIN). The PINS to be used for rod ends acquired to this CID are created as follows: A 52493 - X PIN dash number (see figure 1). CID number. Designates a CID. 5.4 cross-reference data. Rod ends conforming to this CID are substitutable or interchangeable with rod ends confor

18、ming to MS63043C. 5.5 Regulatory requirements. The offerorfcontractor is encouraged to QS recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. MILITARY ACTIVITY: Custodian: Army - AT Air Force - 99 b * Review activities: Air Force - 82 CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Preparing activity Army - AT (Project 5340-2176) User activities: Army - MI Navy - MC, OS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-