ARMY A-A-52505 A-2011 RETAINER BATTERY (METRIC).pdf

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to DAMI_STANDARDIZATIONconus.army.mil or U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501

2、 E. 11 Mile Road, Warren, MI 48397-5000. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 6160 METRIC A-A-52505A May 09, 2011 SUPERSEDING A-A-52505 October 28, 1994 COMME

3、RCIAL ITEM DESCRIPTION RETAINER, BATTERY (METRIC) The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers battery retainers, used widely in automotive tactical vehicles to hold secure 2HN and 6TMF or 6TA

4、GM batteries. 2. CLASSIFICATION. The battery retainers shall be classified as follows (see 7.3): Type A - 2HN single battery Type B - 2HN double battery Type C - 6TMF or 6TAGM double battery 3. SALIENT CHARACTERISTICS 3.1 Material. The battery retainer shall be made of hot rolled commercial quality

5、(HRCQ) carbon steel, pickled and oiled (PO) sheet or strip as per ASTM A1011/A1011M, or cold rolled commercial quality (CRCQ) sheet or cold rolled (CR) strip as per ASTM A1008/A1008M, 1009 to 1020, temper 2 to 5. The use of recovered material made in compliance with regulatory requirements is accept

6、able providing all requirements of this CID are met (see 4). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52505A 2 Figure 1. Type A, battery retainer for 2HN single battery. Provided by IHSNot for ResaleNo reproduction or networking permitted

7、without license from IHS-,-,-A-A-52505A 3 Figure 2. Type B, battery retainer for 2HN double battery. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52505A 4 NOTE: Dimensions are in millimeters. Unless otherwise specified, tolerances are .8 mm. F

8、IGURE 3. Type C, battery retainer for 6TMF or 6TAGM double battery. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52505A 5 3.2 Design and construction. Unless otherwise specified in figures 1 thru 3, the design and construction of the battery r

9、etainers shall be in accordance with the manufacturers specifications and drawings. 3.2.1 Welding. The welding of the battery retainer shall be appropriate for highly stressed joints per AWS D1.1. 3.2.2 Spotwelding. The maximum carbon content of the battery retainer spots to be welded shall not exce

10、ed 0.20 percent (%) in accordance with AWS C1.1. After welding the outer surface of spots shall be smooth and free of cracks, tip pickup, pits, and metal expulsion. 3.3 Finish. 3.3.1 Cleaning. The cleaning of the battery retainer shall be per the manufacturers cleaning standard. The retainer parts s

11、hall be free of oil, grease, wax, dirt, acid, rust and should not show visible signs of corrosion products. 3.3.2 Galvanizing. The retainer assembly shall be hot-dip galvanized in accordance with ASTM A123/A123M, Thickness Grade 100, prior to plastisol coating. 3.3.3 Plastisol coating. The battery r

12、etainer shall be spray coated with plastisol, 0.25 mm thick. This coating shall be free from runs and sags and shall provide maximum resistance to corrosion, abrasion, and chemicals. 3.3.4 Rubber dip coating. Rubber dip coating with polychloroprene is optional, it shall be 0.25 mm thick and done as

13、per M2BC505F17 of ASTM D2000. 3.4 Identification marking. Identification marking shall be permanent and legible and shall include, as a minimum, the part identification number (PIN) and the manufacturers CAGE code and part number (see 7.2 and 7.3). 4. REGULATORY REQUIREMENTS. The offeror/contractor

14、is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS 5.1 Product conformance. The products provided shall meet the salient characteristics of this Commercial Item

15、 Description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to require proof of such conformance. 6. PACKAGING. Preservation, packaging, pack

16、ing, labeling, and marking for the desired level shall be as specified in the contract (see 7.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52505A 6 7. NOTES (This section contains information of a general or explanatory nature that may be

17、helpful but is not mandatory.) 7.1 Source of socuments. 7.1.1 Federal acquisition regulation. Copies of the FAR are available from http:/www.acquisition.gov/far/. 7.1.2 ASTM standards. Copies of ASTM A123/A123M “Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

18、”, ASTM A1008/1008M “Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low Alloy with Improved Formability, Solution hardened, and Bake Hardenable”, ASTM A1011/A1011M “Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon

19、, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength”, and ASTM D2000 “Standard Classification System for Rubber Products in Automotive Applications” are available from the American Society for Testing and Materials, 100 Barr Harbor Drive,

20、 West Conshohocken, PA 19428-2959. 7.1.3 AWS standards. Copies of AWS C1.1 “Resistance Welding Recommended Practices For”, and AWS D1.1 “Structural Welding Code-Steel” are available from the American Welding Society, 550 N.W. Lejune Road, P.O. Box 351040, Miami, FL 33135 (see 7.2). 7.2 Ordering data

21、. Acquisition documents must specify the following: a. Title, number, and date of this CID. b. If required, the specific issue of individual documents referenced (see 7.1.1, 7.1.2, and 7.1.3). c. PIN and quantity required (see 3.4 and 7.3). d. Selection of applicable level and packaging requirements

22、 (see 6). 7.3 Part or identification number (PIN). The PINs to be used for battery retainers acquired to this CID are created as follows (see 3.4 and 7.2): A 52505 - X Type of battery retainer (see 2): A, B, or C CID number CID designator Provided by IHSNot for ResaleNo reproduction or networking pe

23、rmitted without license from IHS-,-,-A-A-52505A 7 7.4 Cross-reference data. Battery retainers conforming to this CID are substitutable/ interchangeable with battery retainers conforming to MS53046C, dated 20 July 1973. PIN numbers to former part numbers are as follows: CID PIN Former MS Part Number

24、Former Army Part Number Battery Type Normally Used A52505-A MS53046-1 8754765 2HN (single) A52505-B MS53046-2 7415701 2HN (double) A52505-C MS53046-3 8345000 11639629 6TMF or 6TAGM (double) 7.5 Key words. 2HN 6TAGM 6TMF Electrical MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FAS Custo

25、dians: Army - AT Preparing Activity: Air Force - 99 Army AT Navy - MC Review Activities: (Project 6160-2011-001) Army MI, CR4 Air Force - 84 DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-