ARMY A-A-52533-1995 TRUCKS HAND PLATFORM FOUR WHEELED TILT AND NON-TILT SOLID RUBBER TIRES OR PLASTIC TIRES (METRIC)《公制实心橡胶轮胎或塑料轮胎倾斜和非倾斜四轮的手动卡车》.pdf

1、A-A-52533 9999974 0169164 592 METRIC A-A-52533 - SUPERSEDING MIL-T-43218D 11 April 1986 COMMERCIAL ITEM DESCRIPTION TRUCKS, HAND, PLATFORM, FOUR WHEELED, TILT AND NON-TILT, SOLID RUBBER TIRES OR PLASTIC TIRES (METRIC) The General Services Administration has authorized the use of this commercial item

2、 description (CID) for all federal agencies. 1. ScOpE. This CID covers requirements for platform hand trucks, with solid rubber tire or plastic tire wheels. The trucks are intended for carrying light items over short distances. 2. SALIENT CHARACTERTSTICS 2.1 Materials * . Unless otherwise specified

3、herein, materials shall be in accordance with the manufacturers material specifications. The use of recovered material made in compliance with regulatory requirements is acceptable providing that all requirements of this CID are met (see 5.4). Asbestos, cadmium, and radioactive material will not be

4、used in this item. Radioactive material is defined by 1) Title 10, Code of Federal Regulations, Part.40, and 2) Other radioactive material in which the radioactivity is greater than 0.002 microcuries per gram or 0.01 microcuries total activity for the item. 2.2 . Platform hand trucks (hereinafter ca

5、lled 44trucks”), shall consist of a metal frame, a metal or wood deck, four push bar or rack sockets, one or two push bars or racks, two swivel casters, two rigid casters, caster supports or axles and axle brackets, and plastic or rubber tired wheels. In addition, rubber bumpers may be required. Tru

6、ck sizes and rated capacities shall be as shown in table I. Beneficial comments, recommendations, additions, deletions clarifications, etc. and any other data which may improve this document should be sent by letter to: US. Army Tank-automotive and Armaments Command, ATTN: AMSTA-TR-EBLUE, Warren, MI

7、 48397-5000. FSC 3920 T A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-52533 9999974 0369365 429 A-A-52533 2.2.1 -. 2.2.1.1 cut, formed and welded at the corners to form a one piece con

8、struction deck and channel frame; or, the frame and deck may consist of a one piece steel sheet welded atop a welded frame assembly. The frame and deck shall be a level rigid unit. The frame comers shall not have sharp comers. . The frame and deck may be fabricated from one steel sheet; 2.2.1.2 clas

9、s 2 - Wood v . The frame assembly, consisting of an outer frame and reinforcing members, shall be of welded steel construction to form a level rigid unit. The frame comers shall not have sharp comers. The deck shall be fabricated from boards of hardwood which have been sanded, sealed and finished on

10、 all wood surfaces in accordance with best commercial practices. Joint spacings between boards shall not exceed 3 mm (0.125 inch). Where required, boards shall be cut and shaped to accommodate push barhack legs. The deck boards shall be removable for replacement. The top surface of the deck boards s

11、hall be flush with top of outer frame or top surface of steel deck band if used. The board ends shall be fully protected by the outer frame. 2.2.1.3 class 3 - AluminumElatfami . The frame and deck, consisting of an outer frame, reinforcing members, and a tread pattern deck, shall be fabricated from

12、aluminum material. The frame and deck shall be of welded construction to form a level rigid unit. The frame comers shall be rounded. 2.2.1.4 sockets. Sockets for push barhack legs shall be permanently affixed, one each, at or near each comer of the deck. The sockets may be located outside or inside

13、of the channel frame. The sockets shall be designed to provide a stop and support for the push barhack legs. The socket hole shall provide for a snug fit for the push barhack legs and a set screw to secure the legs may be provided. 2.2.1.5 p. Caster supports and axle brackets shall be rigidly attach

14、ed to the underside of the frame assembly. 2.2.1.6 two axle-mounted load wheels. Swivel and rigid casters shall be bolted to the caster supports. Load wheels shall be mounted on the axle near the ends. Casters and load wheels shall be manufacturers standard components unless otherwise specified in c

15、ontract or order (see 5.1). . Running gear shall consist of two swivel casters, and two rigid casters or 2.2.1.7 Type 1 - Nm-tilttnicks . Non-tilt style trucks shall have running gear assembled to the underside of the frame assembly such that the load wheels or rigid casters will carry two-thirds of

16、 the rated load plus or minus 11.3 kg (25 pounds). 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52533 9999974 01691ibb 365 A-A-52533 2.2.1.8 Tdype TT - TilLmks . Tilt style trucks shall have the rigid casters or load wheels located widthwise

17、 across the center of the truck, and the two swivel casters to be located one at or near each end of the longitudinal centerline of the truck. 2.2.1.9 Axle. The axle shall be one piece and shall be fabricated from steel. The axle with load wheels shall be assembled to the axle brackets. The load whe

18、els shall not extend beyond the width of the deck. The axle shall not rotate with the wheel. 2.2.2 -. 2.2.2.1 Push. As specified in contract or order, the truck shall be supplied with one or two push bars. The push bar shall be fabricated from iron or steel pipe or tubing. The push bar shall be U-sh

19、aped. The top portion or handle end of the push bar shall be bent outward from the vertical. Aluminum push bars may be supplied for Class 3 trucks provided they meet the strength requirements in 2.2.3.4. 2.2.2.2 Racks. As specified in contract or order, the truck shall be supplied with one or two en

20、d racks. The racks shall be fabricated from iron or steel pipe or tubing and shall be reinforced by at least three equally spaced crossmembers. The outer frame of the racks shall be U-shaped. The top portion or handle end of the rack shall be bent outward from the vertical. Aluminum racks may be sup

21、plied for Class 3 trucks provided they meet the strength requirements in 2.2.3.4. 2.2.2.3 v. When specified in contract or order (see 5.1), the truck shall be supplied with a non-marking rubber bumper assembly. The bumper assembly shall consist of strip and corner bumpers with a reinforcing steel in

22、sert. The bumper assembly shall completely encircle the truck frame, including the sockets. The uppermost surface of the bumper assembly shall be below the top surface of the deck. The bumper assembly may be rigidly fastened directly to the outside of the truck frame or indirectly by means of steel

23、brackets using bolts, self- locking nuts and flat washers. When protection from the handle is needed, donut bumpers shall be specified for each leg (see 5.1). 2.2.2.4 272 kg (600 pound) capacity 991 mm (39 inch) long by 483 mm (19 inch) wide by 127 mm (5 inch) high; 363 kg (800 pound) capacity 1219

24、mm (48 inch) long by 610 mm (24 inch) wide by 356 mm (14 inch) high; 453 kg (1000 pound) capacity 2 1 2 1524 mm (60 inch) long by 762 mm (30 inch) wide by 356 mm (14 inch) high; 1134 kg (2500 pound) capacity 1829 mm (72 inch) long by 914 mm (36 inch) wide by 356 mm (14 inch) high; 1134 kg (2500 poun

25、d) capacity 3 T 1 1829 mm (72 inch) long by 914 mm (36 inch) wide by 356 mm (14 inch) high: 11 34 kg (2500 pound) capacity 5.3 Crass-refemmdata . Trucks conforming to this CID are interchangeable/substitutable with trucks conforming to MIL-T-43218D. 5.4 Regukbry recpbamts . The offeror/contractor is

26、 encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52533 MILITARY INTEMSTS: Custodians: P Army - AT Navy - SA Air Force - 99 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY Army - AT (Project 3920-0008) Review Activities: Navy - MC, SH, YD-1 Air Force - 84 DLA - GS 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-