ARMY A-A-52545 B-2009 HEATERS VEHICULAR COMPARTMENT 28 VOLT DC《28伏直流车厢加热装置》.pdf

1、Comments, suggestions, or questions on this document should be addressed to U.S. Army Tank-automotive and Armaments Command, ATTN: RDTA-EN/DM/STND, MS# 268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact information can change, you may wan

2、t to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 2540 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-52545B 03 August, 2009 SUPERSEDING A-A-52545A February 4, 1997 COMMER

3、CIAL ITEM DESCRIPTION HEATERS, VEHICULAR COMPARTMENT 28 VOLT, DC The General Services Administration has authorized the use of this commercial item description (CID) for all federal agencies. 1. SCOPE. This CID covers two types of heaters of 28 volt (V) direct current (dc) nominal rating, used for h

4、eating crew and engine compartments of military vehicles or equipment. Type I heaters are intended for use on military vehicles or equipment which may be required to operate in an ambient temperature to minus 65 degrees Fahrenheit (-65F); from which a supply of gasoline is available; when heated air

5、 is required without the vehicle engine being operated. Type II heaters are intended for use on military vehicles or equipment from which a supply of heated circulating liquid (engine coolant) is available, which may be required to operate in an ambient temperature to -25F. 1.1 Classification. Heate

6、rs shall be of the following types and capacities, as specified (see 6.2): Type I - Gasoline Fired: Capacity A - 20 000 British thermal units per hour (Btu/hr). Capacity B - 30 000 Btu/hr. Capacity C - 60 000 Btu/hr. Type II - Liquid Coolant Operated: Capacity B - 30 000 Btu/hr. Provided by IHSNot f

7、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 2 2. SALIENT CHARACTERISTICS 2.1 Materials. Materials for type I heaters shall be as specified in the applicable engineering drawing (AED). Materials for type II heaters shall be in accordance with the manufactu

8、rers material specifications for heaters. The use of recovered material made in compliance with regulatory requirements is acceptable providing all requirements of this CID are met (see 4.1). 2.2 Design and construction. Unless otherwise specified, type I heaters shall fall within the envelope outli

9、ne of the AED and shall conform to the detail requirements for mounting dimensions, external electrical connections and fuel inlet. Type II heaters shall be constructed in accordance with figures 1, 2, and 3. Type I and type II heaters shall meet the applicable requirements of Federal Motor Carrier

10、Safety Regulations (FMCSR) in effect on date of manufacture. 2.2.1 Interchangeability. All parts having the same manufacturers or Army part numbers shall be completely interchangeable with each other with respect to installation and performance. 2.3 Controls. When specified (see 6.2), heaters shall

11、be furnished complete with controls to start, stop, and operate heaters. 2.4 Coolants. Type II heaters shall perform as specified herein using the following type coolants/rust inhibitors: a. Water and 60% concentration of antifreeze compound conforming to A-A-52624. b. Arctic type antifreeze compoun

12、d of a single phase homogeneous mixture. This compound shall provide protection against freezing in regions where the ambient temperature remains close to -40F for extended periods of time, but may drop to as low as -90F. c. Water and corrosion inhibiting compound consisting of the chemical composit

13、ion shown in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 3 NOTES: 1. Dimensions are in inches, maximum, except detail C, unless otherwise specified. Detail C tolerances are +0.06. 2. Basic assembly is shown. Heater may be adap

14、ted to various configurations by rearranging or interchanging end panels or blower housing attachment. FIGURE 1. Type II heater. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 4 NOTES: 1. Dimensions are in inches. Unless otherwise specifi

15、ed tolerances are +0.010 for shell, +0.003 for washer and + 0.007 for terminal. 2. The cable shall be unshielded single conductor type, 14 AWG size, with outside diameter of 0.160 +0.010. The cable shall be designed and constructed as shown in A-A-52499. 3. Shell material shall be rubber grade M5BC6

16、10A14C12E034F19 or equivalent as specified in ASTM D2000. 4. Shell shall be marked “OZ” (ozone resistant). 5. Washer material shall be brass, temper 2 hard minimum. 6. Finished washer shall have burrs and sharp edges removed. 7. Terminal material shall be brass, temper 2 hard minimum. 8. Terminal fi

17、nish shall be silver plate, 0.0002 minimum thickness. FIGURE 2. Type II heater connector assembly. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 5 NOTES: 1. Material shall be brass. Handle may be zinc plated steel. 2. Dimensions are in i

18、nches. FIGURE 3. Type II - Heater vent. TABLE I. Chemical composition. Components Weight percent Distilled or deionized water (total added) Sodium metaborate (Na2BZO4 8H2O) Potassium Silicate solution Sodium mercaptobenzothiazole, 50% agueous solution, by weight 63.4 +0.6 29.0 +0.3 4.6 +0.2 3.0 +0.1

19、 2.5 Fuel. Type I heaters shall perform as specified in 2.6.1 using military combat grade automotive gasoline or commercial grade automotive gasoline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 6 2.6 Performance. 2.6.1 Type I heater.

20、2.6.1.1 Heat output. With inlet air temperature at -65 +5F, the type I heaters shall have a heat output as specified in table II. 2.6.1.2 Air discharge rate. The type I heaters when performing at high setting, shall discharge air at not less than the rates specified in table II. 2.6.1.3 Fuel flow. C

21、onsumption of gasoline conforming to 2.5 in type I heaters shall not exceed the flow rate values specified in table II. TABLE II. Type I Heaters. Capacity A B C Heat output: High setting 18 000 27 000 54 000 Btu/hr. Low setting 7 200 16 200 27 000 Air discharge: Unrestricted 80 105 200 ft3/min 1/ Ai

22、r back pressure 50 at 0.5 inch H20 85 at 1 inch H20 150 at 1 inch H20 Fuel flow: High heat 0.29 0.48 0.83 Gal/hr. Low heat 0.13 0.30 0.44 Current: Start 12 18 21 Amperes Run 4 7 11 1/ ft3/min = cubic feet per minute. 2.6.1.4 Current. Using a starting voltage of 24 +0.5 Vdc and a test ambient tempera

23、ture of -65F, the current shall be not more than the values specified in table II. 2.6.1.5 Overheat switch. The overheat switch shall break the circuit and cut off the flow of fuel when the ventilating air mixed with ambient air is heated to a temperature of 375 +25F. 2.6.1.6 Cycling. Type I heaters

24、 shall start in less than four minutes and purge in less than three minutes when cycled at high setting for 50 cycles at an ambient temperature of -65 +5F. Each cycle shall consist of starting at high heat, running for 15 minutes, purging, and cooling the heater for 35 minutes with auxilary blower.

25、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 7 2.6.1.7 Endurance. The heater shall operate without a breakdown of the heat exchanger, electrical motor, combustion air blower wheel, ventilating air blower wheel, or fuel control valve dur

26、ing not less than 500 hours of continuous use, operating at ambient temperatures as low as -65F, alternately at high and low heat settings, for 24 hour periods and cycling 20 minutes “ON“ and 10 minutes “OFF“. 2.6.1.8 Safety. All heaters shall comply to DOT standards cited in 49 CFR, section 177.834

27、 in effect on date of manufacture. 2.6.2 Type II heaters. 2.6.2.1 Heat output and air discharge. The heat output and air discharge rate shall be not less than values in table III, as determined per SAE J638 procedure. TABLE III. Type II heat output and air discharge. Inches H2O back pressure Heat ou

28、tput Btu/hr Air discharge: ft3/min 0 1.6 28 000 15 000 150 75 2.6.2.2 Cycling. The heater shall have no coolant leakage from the coolant circulation system when cycled at 20 cycles per minute, pressure rise and fall from 0 to 32 pounds per square inch (psi), for 2500 total cycles. Cycling shall be a

29、ccomplished at ambient temperature of -25 +5F. 2.6.2.3 Endurance. The heater shall operate without a breakdown of the heat exchanger, electric motor or fan during not less than 250 hours of continuous operation with a coolant temperature of 180 +5F with zero back pressure, and not less than 250 hour

30、s with 1.6 inches of H2O back pressure. Starting time to full load shall be 10 seconds maximum. 2.6.3 Type I and II heaters. 2.6.3.1 Voltage. The heater shall start and operate satisfactorily at an applied voltage of 20 to 28.5 Vdc. 2.7 Environmental. 2.7.1 Low temperature operation. Type I heaters

31、shall have operational stability at temperatures to -65 +5F and type II heaters shall have operational stability at temperatures to -25F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 8 2.7.2 Vibration. The heaters shall start and operat

32、e while vibrating at an amplitude of 0.25 inch for one hour in the direction of each of the three major axes of the heater. While accelerating and decelerating at a uniform rate for an interval of one minute, the frequency shall vary through a range of 10 to 55 cycles per second. There shall be no e

33、vidence of leakage of fuel from the type I heaters, or of coolant from the type II heaters during or after the vibration. 2.7.3 Corrosion resistance. With all duct openings sealed, the heaters shall show no evidence of corrosion that would affect their functioning after being subjected to a 96-hour

34、salt solution spray. 2.7.4 Electromagnetic interference. Unless otherwise specified (see 6.2) or in applicable drawings, the heaters shall meet the electromagnetic interference requirements of products offered commercially. 2.8 Identification and markings. Identification and markings shall be perman

35、ent and legible and shall include as a minimum, the manufacturers identification code (CAGE), the engineering drawing part number (type I heaters) and PIN AA52545-1 (type II heater). 2.9 Nameplate. A nameplate shall be attached to the heater in a location, such that the plate may be easily read when

36、 the heater is installed in the vehicle. The location of the nameplate shall be as specified in the contract or ordering data (see 6.2). The nameplate shall contain the following minimum information: HEATER 28 VOLTS DC ENGINEERING DRAWING PART NUMBER (TYPE I HEATERS) PIN AA52545-1 (TYPE II HEATERS)

37、MANUFACTURERS IDENTIFICATION MANUFACTURERS SERIAL NUMBER 2.10 Painting. The exterior surfaces of the type I heater case and outlet adapter shall be cleaned, degreased, and then painted with paint heat tested to 400F. Other surfaces of the type I heater, and the exterior surfaces of the type II heate

38、r shall be finished as specified in the contract (see 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 9 3. QUALITY ASSURANCE PROVISIONS 3.1 Product conformance. The products provided shall meet the salient characteristics of this com

39、mercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 4. REGULATORY REQUIREMENTS 4.1 Recov

40、ered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR) (see 2.1). 5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or orde

41、r (see 6.2). 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Addresses for obtaining copies of referenced documents. 6.1.1 Government documents. Copies of FMCSR 49 CFR Parts 100 to 177 can be obtained from Superintendent

42、of Documents, Government Printing Office, Washington, DC 20402-9371. Copies of A-A-52624 “Antifreeze, Multi Engine Type” and A-A-52499 “Lead, Electrical (Storage Battery)” are available from the Defense Printing Services Detachment Office, Bldg. 4D (Customer Service), 700 Robbins Avenue, Philadelphi

43、a, PA 19111-5094. 6.1.2 Non-Government documents. Copies of SAE J638 “Motor Vehicle Heater Test Procedure, Recommended Practice,” can be obtained from the Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096. Copies of ASTM D2000 “Standard Classification System for Rub

44、ber Products in Automotive Applications (SAE Recommended Practice J200) (DoD Adopted)” can be obtained from American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

45、HS-,-,-A-A-52545B 10 6.2 Ordering data. Acquisition documents must specify the following: a. Title, number, and date of this CID. b. Issue of Department of Defense Index of Specifications and Standards (DoDISS) and the specific issue of individual documents referenced. c. Type and capacity of heater

46、 (see 1.1). d. Title, number, and revision letter of the AED for type I heaters. e. PIN for type II heaters. f. Quantity of heaters required. g. Electromagnetic interference requirements if other than commercially available (see 2.7.4). h. Location of nameplate (see 2.9). i. If controls are to be fu

47、rnished. j. Surface finish of heaters (see 2.10). k. Selection of applicable level of packaging requirements (see 5). 6.3 Part identification number (PIN). The PINs to be used for gaskets acquired by this CID, are created as follows: A 52489 - X Type 1 Type II Heater CID number CID designator 6.4 Cr

48、oss-reference. Heaters conforming to this CID are interchangeable/substitutable with heaters conforming to MIL-H-3199E and MS51326A(AT). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52545B 11 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS Custodians: Army - AT Preparing Activity: Navy - MC Army - AT Air Force 99 (Project 2540-2009-001) Reviewer Interest: DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations a