ARMY A-A-52600-1996 TANK LIQUID STORAGE METAL FUEL-OIL HORIZONTAL《横向燃油金属贮存罐》.pdf

1、A-A-52b00 = 9999974 0370770 Tb4 G METRIC A-A-52600 blmhLw% SUPERSEDING MIL-T-462E 16 September 1985 Beneficial comments, recommendations, additions, deletions clarifications, etc. and any other data which may improve this document should be sent by letter to: U.S. Army Tank-automotive and Armaments

2、Command, ATTN: AMSTA-TR-E/BLUE, Warren, MI 48397-5000. - COMMEXCIAL ITEM DESCRIPTION TANK, LIQUID STORAGE, METAL: EUEL-OIL, HORIZONTAL The General Services Administration has authorized the use of this Commercial Item Description (CID) for all federal agencies. 1. SCOPE. This CID covers a 1041 liter

3、 (L) (275 gallon (gal) nominal capacity, horizontal, non-pressure type, above ground fuel oil storage tank. The tank is intended for unenclosed installation inside of buildings, primarily for the storage and supply of fuel oil for oil burners. Outdoor installation is not precluded. 2. SALIENT CHARAC

4、TERISTICS 2.1 Materials. Unless otherwise specified herein, materials shall be in accordance with the applicable requirements of Underwriters Laboratories, Inc., UL 80. The use of recovered material made in compliance with regulatory requirements is acceptable providing that ail requirements of this

5、 CID are met (see 3.1). 2.1.1 -ade steel . The tank shall be constructed of commercial grade steel having a less than 1.70 millimeter (mm) (0.067 inches (in) and for galvanized steel, 1.78 mm (0.070 in). - carbon content of 0.25 percent or less. The minimum thickness of uncoated steel shall be not r

6、 Licensed by Information Handling ServicesA-A-52b00 m 9999974 OL7077L 9TO m A-A-52600 2.2 -and constructiqn. 2.2.1 m. The tank shall be fabricated in accordance with the requirements of Underwriters Laboratories Inc., UL 80. The tank shall have the form as shown in Figure 1. 12 in (300 mm) ft9 in 40

7、 rnm) L II I 275 GALLONS ( 1041 L ) 0.50 in b (13 mm 0) (75 mm) -5 ft O in(1520 mm)- NOTES: 12 in (300 rnm) 1. All openings internaiiy threaded NPT. 2. Tolerance on dimensions locating openings is f13 mm (0.50 in). 9 FIGUREl. Tank. 2 Licensed by Information Handling ServicesA-A-52600 9999974 0370772

8、 837 A-A-52600 2.2.2 Shell seams. Welding shall be of the continuous or lap type. AU lap welds shall have a continuous full et the length of the seam. 2.2.3 Mounting brackets. Two 100 by 100 by 6.4 mm (4 by 4 by 0.25 in) steel angle brackets 100 mm (4 in) long shall be welded, with a continuous fidl

9、 fiilet weld, on each side of the tank. The brackets shall be located 15 mm (6 in) from the ends of the tank. Each bracket shall be drilled and tapped for a 32 mm (1.25 in) pipe leg. 2.2.4 Fill. vent and gauge openinas. Not less than three threaded openings shall be provided in the top of the tank f

10、or connection of fiil and venting piping, and for installation of a liquid level gauge. Au openings on the top of the tank shaii be equal in size and not less than a nominal 50 mm (2 in) pipe size. 2.2.5 Top piPe connections. Stamped or forged steel pipe connections shall be furnished by welding thr

11、eaded flanges to the tank openings. The connections shall be in accordance with the requirements of Underwriters Laboratories Inc., (VL) 80. 2.2.6 Burner supplv connection. A threaded opening not less than 13 mm (0.50 in) pipe size shall be provided in the bottom of the tank shell for connection of

12、piping supplying fuel to the oil burner. The center of this opening shall be located not more than 75 mm (3 in) from the end of the shell, and the opening shad be without internai projections to permit complete drainage. A burner supply connection shaU not be located in a head. 2.2.7 Treatment and p

13、ainting;. The parts of the tank normally painted shall be cleaned, treated and painted in accordance with the contractors commercial practice. Unless otherwise specified in the contract, the fnish coat shall be camouflage green. 2.2.8 Identification marking number. Each tank shall be marked with the

14、 manufacturers or private labelers name or identwg symbol. This marking shall be embossed, etched or stamped on a metal nameplate that is permanently attached by welding or brazing. Ea mandacturer produces tanks at more than one factory, each tank shall have a distinctive marking to identify it as t

15、he product of a particular factory. In addition, identification marking shall include the mandacturers identification code (CAGE), manufacturers part number and the part identification number (PIN), A-A-52600 (see 6.2). 2.2.9 Installation marking. Each tank shall be permanently marked with the follo

16、wing: “For proper operation, (1) Upon installation pitch tank longitudinally, toward drain, at least 6.4 mm (0.25 in) per foot of tank length; (2) Vent pipe diameter must be at least equal to i pipe diameter. A signaling device installed in vent pipe shall not reduce venting capacity; and (3) Consul

17、t local authorities before installation of tank”. The required marking shail be ink- stamped or paint-stenciled on the tank, or printed on an adhesive-backed label. Minimum letter 3 Licensed by Information Handling ServicesA-A-5 2 b 00 9999974 0370773 773 A-A-52600 height shall be 2.4 mm (0.094 in).

18、 A contrasting background shall be provided for legibility. An adhesive-backed label shail comply with the applicable Underwriters Laboratories requirements for indoor use labels and exposure to No. 1 and No. 2 fuel oil. 22.10 Safety marking. The tank shail be stenciled in 50 mm (2 in) lusterless re

19、d letters on both sides of the tank “Flammable - Keep Fire Away”. 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation FW. 4. QUALITY AS

20、SURANCE PROVISIONS 4.1 Responsibility for inspection. The contractor is responsible for the performance of all inspections (examinations and tests). 4.2 Contractor cerification. The contractor shall ce* and maintain substantiating evidence that the product offered meets the salient characteristics o

21、f this CID and that the product confonns to the producers own drawings, specifications, workmanship standards, and quality assurance practices. Items with known defects shall not be submitted for Government acceptance. The Govment reserves the right to require proof of such codormance prior to the r

22、st delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order (see 6.2). 6. NOTES (This section contains information of a general or explanatory nature that may be help

23、ful but is not mandatory.) 6.1 Addresses for obtaining; copies of referenced documents. 6.1.1 Other Government documents. The Code of Federal Regulation (CFR) is available fiom the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402. 6.1.2 Non-Government publications.

24、 UL document “Steel Inside Tanks for Oil-Burner Fuel - UL80” is available fiom Underwriters Laboratories, Inc. (UL), 333 Pfhgsten Road, Northbrook, IL 60062-2096. 4 Licensed by Information Handling ServicesA-A-52600 9999974 0370774 bOT A-A-52600 6.1 Addresses for obtaining; copies of referenced docu

25、ments. 6.1.1 Other Government documents. The Code of Federal Regulation (CFR) is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. 6.1.2 Non-Government publications. UL document “Steel Inside Tanks for Oil-Burner Fuel - UL80” is available fiom Und

26、erwriters Laboratories, Inc. (UL), 333 Pfingsten Road, Northbrook, t IL 60062-2096. 6.2 Acauisition data. Acquisition documents must speciSl the following: a. Title, number, and date of this CID. b. Issue of Department of Defense Index of Specifications and Standards ODISS) to be cited in the solici

27、tation, and ifrequired, the specific issue of the individual documents referenced. c. Ifpainting other than as specified. d. Emarking other than as specified. e. PIN and quantity of tanks required. f Preservation, packing, and marking not as specified in the contract. 6.3 Cross-reference data. Tanks

28、 conforming to this CID are interchangeabldsubstitutable with tanks conforming to MIL-T-462. MILITARY INIBRESTS: Custodians: Army - AT Navy-YD1 Air Force - 99 CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS Preparing Activity: Army - AT (Project 5430-024 1) Review Activities: Air Force - 84 Navy - MC DLA - CS 5 Licensed by Information Handling Services