ARMY A-A-56011-1989 HANDLE FOLDING MALE 90 DEG DETENT《90度可折叠男士制动器手柄》.pdf

1、A-A-56011 16 August 1989 COMMERCIAL ITEM DESCRIPTION HANDLE, FOLDING, MALE 90“ DETENT Abstract. This Commercial Item Descript folding, male 90“ detent. Salient characteristics. 2 PL / ion covers one type of handle, REF . FIGURE 1 FIGURF: 2 m m-a .3l25-24 .500 .625 .375 2.375 5.225 2.375 .625 4.500 .

2、375 -101 PTENX N MR L EH D A m. T -102 .562 .m 3; 5.562 3.000 5.000 .m -103 .375 1.30 3.625 1.310 3.000“ f.m -104 .440 -105 1.750 7.065 1.750 6.440 35898-5270. DISTRIBUTION STATEMENT A. Appro- f iti is unlimited. _7 THIS DOCUMENT CONTAINS 3 PAGES. Provided by IHSNot for ResaleNo reproduction or netw

3、orking permitted without license from IHS-,-,-Notes : 1. Handles shall be detent for two positions 90“ apart (see figure 2). 2, Materi al . Aluminum type 2011-13 per QQ-A-225/3, Ring material per MIL-P-25732. 3. Protective finish, Clear anodized per MIL-A-8625, Type II, Class 1, 4. Hardware, Handles

4、 shall be supplied with unattached mounting hardware consisting of 2 internal tooth lock washers , 2 nuts, and 2 liOl1 Rings as fol 1ovs: Lock washers shall be phosphor bronze, nickel plated per QQ-N-290, Class 1, Type I , Nuts shall be aluminum type 2011-T3 per QQ-A-225/3, clear anodized per MIL-A-

5、8625, Type II, Class 1. King material as stated above, Contractor certification, The contractor shall certify and maintaiil substantiating evidence that tile product offered meets the salient characteristics of this Comlnerci al Item Description, and that the product conf orrfls to the producer I S

6、own drawi ngs , specif i cat ions,. standards, and quality assurance practices, The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric products. Products manufactured

7、to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided xhey fall within specified tolerances using conversion tables contaifled in the latest revision of Federal Standard No. 376, and all other requirements of tnis Commercial Item Descripti

8、on are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inchlpound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the optioil of accepting or rejecting

9、 tne product . Regulatory requirements, The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable, Preservation, packaging, packing, labeling, and marking. Preservation, packaging, packing, labeling, and marking shall be as

10、 specified in the contract or order, 2 J Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-56011 53 m 777777LI 0002355 O W A-A-56011 CID based part identjfication number. The following part identification numbering procedure is for Government purpo

11、ses and does not constitute a requirement for the contractor. . Example:- A-56011-101 Designates dash number (see table I) CID Nmber I Designates a CID Notes. 1. Size and quantity rzquired shall be as specified in the contract or order (sec table 1). 2. FEU-STd-375 is avai lable from the iiaval Publications and Forms Center, 5801 Tabor Avenue, Philadelphia, PA 19123-5099. Custodian: Army - MI 3 Preparing Activity: Army - MI Project No. 5340-AO45 FSC 5340 n Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-