ARMY A-A-56024-1993 FOIL TITANIUM《钛箔》.pdf

1、A-A-5 bo24 m 9999934 0121533 267 m I INCH-POUND I A-A-5 6 02 4 20 January 1993 COMMERCIAL ITEM DESCRIPTION FOIL, TITANIUM The General Services Administration has authorized the use of this Commercial Item Description. Abstract. This commercial item description covers one kind of titanium foil. The f

2、oil is intended for use in fabrication of electrical equipment for one submunition system. Salient characteristics. The chemical composition of the material shall meet the requirements of ASTM B 265, Grade 2. The thickness shall be 0.000100 to 0.000125“; the width shall be not less than 3.25“- The f

3、oil shall be cold rolled to reduce the material 85 to 95%. The surface shall be free of contamination, holes, wrinkles, creases, tears, cracks and seams. Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteris

4、tics of this Commercial- Item Description, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provid

5、ed for under the provisions of the contract. Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances Beneficial comments, recommendations, additions, deletions, cla

6、rifications, etc. and any data which may improve this document should be sent to: Commander, U.S. Army Missile Command, ATTN: AMSMI-RD-SE-TD-ST, Redstone Arsenal, AL 35898-5270. AMSC N/A FSC 6610 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. , Provided by IHSNot f

7、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5b024 9999974 0323538 LT3 A-A-5 602 4 using conversion tables contained in the latest revision of FED- STD-376, and all other requirements of this Commercial Item Description are met. If a product is manufactured to me

8、tric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. to use recovered materials IAW Pu

9、blic Law 94-580 to the maximum extent practical. preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. identification number procedure is for government purposes and does not constitute a requirement for the contractor. Regulatry reguirements. The of

10、feror/contractor is encouraged Preservation, packaging, packing, labeling, and markinq. The CID-based part identification number. The following part A xxxxx X Example of part identification number A-XXXXX Type # I Example of CID number I I Designates a CID a. Material safety data sheets. Material sa

11、fety data sheets are required by Title 29 Code of Federal Regulations, Section 1910.1200, and shall be prepared in accordance with the requirements of FED-STD-3i3. those activities requiring copies of completed material safety data sheets prepared in accordance with FED-STD-313. The pertinent Govern

12、ment mailing addresses for submission of data are listed in Contracting officers will identify FED-STD-313. b. Source for reference documents. Copies of referenced federal and military specifications and standards may be obtained by sending a request for copies to the Standardization Documents Order

13、 Desk, Bldg. 4D, 700 Robbins Ave., Philadelphia, PA 19111- 5094: 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-56024 9999974 Ol121539 03T W A-A-5 6 O 2 4 FED-STD-313 - Material Safety Data, Transportation Data and Disposal Data for Hazardous

14、Materials Furnished to Government Activities Use by the Federal Government FED-STD-376 - Preferred Metric Units for General Copies of referenced ASTMs are available from the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187: ASTM B 265 - Standard Specification

15、 for Titanium and Titanium Alloy Strip, Sheet, and Plate c. Acceptable products and part numbers. The products 1 described in this commercial item description are available from: Source Part Number Hamilton Precision Metals, Inc. 1780 Roberstown Road P.O. Box 3014 Lancaster, PA 17604-3014 CAGE Code

16、66729 Arnold Engineering Co. Div. of SPS Technologies West St. 61 Railroad P.O. Box G Mareno, IL 60152 CAGE Code 95566 3 HAvA LIL-1 ANAVA 261-0005-0025-2 ANAVAR 2 6 1 - O O O 5F O O 2 5-2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-56024 D 74

17、 0121540 851 D A-A-5 602 4 MILITARY INTERESTS: Custodian: Army - MI Navy - SH Review Activities: Army - AT Navy - CG DLA - GS CIVILIAN AGENCIES: Coordinating Activities: COM - NIST GSA - 7FXEE PREPARING ACTIVITY: Army - MI Project No. 5970-1108 FSC 6610 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-