ARMY A-A-59202-1998 CHIPBOARD WAD MATERIAL《锰土材料刨花板》.pdf

1、- A-A-59202 9?L, 0377222 O38 W A-A- 59202 31 March 1998 SUPERSEDING MIL-C-60607 (AR) 30 September 1966 COMMERCIAL ITEM DESCRIPTION CHIPBOARD, WAD MATERIAL The General Services Administration has authorized the use of this commercial item description as a replacement of MLL-C-60607 for all federal ag

2、encies. 1. SCOPE. used as wad material in blank rifle grenades and small arms cartridges. This CID covers the general requirements for one type of chipboard 2. SALIENT CHARACTERISTICS. 2.1 Materials. Chipboard shall be made of uncoated and unlined paper. 2.2 Color. The chipboard shall contain no col

3、oring additives. 2.3 Dimensions. chipboard shall be 0.030 to 0.033 inch thick and 7/16 k 1/64 inch wide. The length of the chipboard shall be as specified in the contact or order (see 6.2). Unless otherwise specified in the contract or order, the 2.4 Weisht. mil thickness. The weight in pounds per 1

4、000 ft2 shall be 3.24 k 0.32 pounds per 2.5 pH value. the chipboard shall be 6.5 I 1.5 when tested in accordance with industry standards. When using distilled water, the pH of the hot water extract of Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of

5、use in improving this document should be addressed to: Commander, US Army TACOM-ARDEC, Attn.: AMSTA-AR-EDE-S, Bldg 12, Picatinny Arsenal, NJ 07806-5000 by using the Standardization Document Improvement IProposal (DD Form 1426) appearing at the end of this document or by letter. I AMSC N/A FSC 8140 D

6、ISTRIBUTION STATEMENT A. Approved for public release; distribution is un1 imited. Licensed by Information Handling Services A-A- 592 02 - A-A-59202 W 9999974 0377223 T74 W 2.6 Ash content. industry standards. The ash content shall not exceed 7 percent as determined by 2.7 Combustibilitv. chipboard s

7、hall continue to burn after the flame is removed. When exposed to an open flame for three seconds, the 2.8 Punchabilitv. punched out segment shall show no evidence of tearing or chipping when examined with a 30X lens or microscope. When punched with a standard paper punch, the edges of the 3. REGULA

8、TORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered material to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE PROVISIONS. 4.1 Product Conformance. The products provided shall meet the salient

9、 characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5. PACKA

10、GING. Preservation, packing, and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Source of documents. 6.1.1 Government documents. The Code of Federal Regulations (CFR) is available by mail order from the Superintendent of Documents, ATTN: New Order, PO Box 371954, Pittsburgh, P

11、A 15250-7954 6.2 Orderins data. Procurement documents should specify the following: a. Title, number, and date of this CID. b. Thickness, if other than 0.030 to 0.033 inch thick (see 2.3). c. Width, if other than 7/16 inch, and applicable tolerance (see 2.3). d. Length (see 2.3). 6.3 Kevwords. Paperboard MILITARY INTEREST: CIVIL AGENCY COORDINATING ACTIVITY: OSA- FSS Custodian Army-AR Preparing Activity: Rrmy-AR Project 814 O- 0190 2 Licensed by Information Handling Services