ARMY A-A-59326 11 B-2011 COUPLING HALF PLUG DUST TYPE X.pdf

1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to DAMI_STANDARDIZATIONconus.army.mil or U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501

2、 E. 11 Mile Road, Warren, MI 48397-5000. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 4730 Distribution Statement A. Approved for public release; distribution is unli

3、mited. INCH-POUND A-A-59326/11B April 21, 2011 SUPERSEDING A-A-59326/11A May 1, 2003 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET COUPLING HALF, PLUG, DUST, TYPE X The General Services Administration has authorized the use of this commercial item description for all federal agencies. The complete

4、 requirements for procuring couplings described herein shall consist of this document and the latest issue in effect of A-A-59326. CAM - LO CK INTERFACE (SEE A - A - 59326 ) KE Y RING 1.00 ID ALL SIZES FIGURE 1. Coupling half. Provided by IHSNot for ResaleNo reproduction or networking permitted with

5、out license from IHS-,-,-A-A-59326/11B 2 1. SCOPE. This specification covers a Dust Plug for use with a female cam locking type coupling half. 2. CLASSIFICATION. The size of the dust caps for the coupling halves is designated in table I. TABLE I. Coupling half size. Dash No. Nom. Size 1 2 3 1 4 1 5

6、1 6 2 7 2 8 3 9 4 10 6 NOTE: Sizes are in inches. 3. SALIENT CHARACTERISTICS. The following characteristics differ from those listed in the latest issue of A-A-59326. 3.1 Accessories. The coupling shall be supplied with a key ring and sash chain. 3.2 Sash chain. The key ring shall attach a sash chai

7、n consisting of 19 links, minimum, size 35 in accordance with ASTM A466/A466M, as shown in figure 1. 3.3 Pressure rating. The -inch through 6-inch dust plugs shall be rated for rated for 150 psi (pounds per square inch). 4. NOTES 4.1 Part Identification Number (PIN). The following PIN procedure is f

8、or government purposes and does not constitute a requirement for the contractor. This example describes a part numbering system for specification sheet A-A-59326/11. AA59326/11-10-A; where /11 indicates a Coupling Half, Plug, Dust, Type X, -10 indicates a 6-inch nominal size, -A indicates Aluminum b

9、ody. Material: A - Aluminum Alloy B - Copper Alloy (Brass or Bronze) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59326/11B 3 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FAS Custodians: Army - AT Preparing Activity: Navy - YD

10、 Army - AT Air Force - 99 (Project 4730-2011-023) Review Activities: Army - AV, GL Navy - MC, SH Air Force - 71 DLA - CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-