ARMY A-A-59379-1999 VALVES GATE RISING STEM DOUBLE ACTING LIGHTWEIGHT [Superseded ARMY MIL-V-58039 E CANC NOTICE 2 ARMY MIL-V-58039 E CANC NOTICE 1 ARMY MIL-V-58039 E INT AMD 1 ARM.pdf

1、 CH-POUND I A-A-59379 19 March 1999 SUPERSEDING 26 March 1984 MIL-V-58039E COMMERCIAL ITEM DESCRIPTION VALVES, GATE, RISING STEM, DOUBLE ACTING, LIGHTWEIGHT The General Services Administration has authorized the use of this Commercial Item Description (CID) by all federal agencies. l. SCOPE. This CI

2、D covers double acting, rising stem, gate valves for use with liquid petroleum supply systems. 2. CLASSIFICATION. 2.1 Tvue. Valves shall be classified into three types as follows (see 7.2): Type I -3 inch, round Truck Trailer Manufacturers Association (TTMA) flange ends. Type II -4 inch, round TTMA

3、flange ends. Type III -6 inch, round TTMA flange ends. 3. SALIENT CHARACTERISTICS. 3.1 Description. The valves shall be lightweight, and have a double-acting, rising stem connected to a wedge-shaped double-disk and actuated by manual handwheel. 3.2 Interface. The valves shall have bolt circle and fl

4、ange dimensions in accordance with TTMA RP No. 28 or as shown in table I to allow proper interface with other system components. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may improve this document should be addressed to: U.S. Army Tank-automotive and Ar

5、maments Command, ATTN: AMSTA-TR-D/210, Warren, MI 48397-5000 AMSC NIA FSC 4820 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59379 TABLE I. Valve flange dimension

6、s Size Number of bolts Bolt hole diameter Bolt circle diameter O, D. I/ 3 inch 12 0.438 8.125 9.000 6 inch 8 0.438 5.875 6.750 4 inch 8 0.438 4.875 5.625 NOTE: Manufacturers standard tolerance shall apply. - 1/ O.D. = Outside Diameter. 3.3 Materials. The materials selected for construction are the r

7、esponsibility of the contractor. The materials shall be of sufficient durability to meet all requirements specified herein. Valves shall be constructed of corrosion resistant material suitable for fuel service. 3.4 Valve body. The valve body shall have an area of flow passage, when fully opened, not

8、 less than that of a circle having a diameter equal to the valve nominal pipe size. 3.5 Valve performance. When subjected to a hydrostatic pressure of 300 pounds per square inch gage (psig) for type I and II or 225 psig for type III for a period of not less than one minute, there shall be no leakage

9、 nor visible distortion or evidence of cracks. 3.6 End flanges. The end flanges (inlet and outlet) shall be integral with the valve body and shall meet all requirements of a TTMA flange. 3.7 Bonnet. The bonnet shall be constructed to contain the stuffing box assembly, and shall provide adequate clea

10、rance for the disks when the valve is fully opened. The bonnet shall be removable from the valve body to allow access to the stuffing box assembly for repair. A replaceable means of sealing the bonnet to valve body interface shall be provided. 3.8 Stuffing box. The stuffing box or condensation chamb

11、er shall be self-adjusting and shall consist of a packing nut, packing gland, and gland spring. All components shall be of corrosion resisting materials. 3.9 Packing. Packing shall be the contractors standard product. 3.10 Rising stem. The rising stem shall be of a corrosion resistant material and m

12、ay be of one or two piece construction with a double acting feature for fast closing. The stem shall include a retaining mechanism which prevents the stem and its components from being expelled from the valve under pressure. 3.1 1 Double disk. The disk shall be of the double disk type with a self-al

13、igning feature to assure a positive leak-proof closure. The disks shall be of a corrosion resistant material to ensure continued operation. Disks shall be loosely keyed together to facilitate removal. The disk shall not jam and internal parts shall not be damaged when a force of 2.5 foot-pounds of t

14、orque is applied to the handwheel to close the valve and the same torque is applied to open the valve. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59379 W 9018054 001l131 TL8 M c A-A-59379 3.12 Seat ring. The seat ring shall be of a corrosi

15、on resistant material. The finish of the seat rings and the double disks shall be such that smooth close contact between the components shall prevent leakage but not bind or gall one another during opening and closing. 3.13 Handwheel. The handwheel shall be the contractors standard handwheel securel

16、y fastened to the rising stem. The handwheel shall have direction of rotation, for opening and closing, indicated. 3.14 Finish. Before assembly the valve components shall be anodized with a color as specified (see 7.3). The coating shall be of a thickness to allow assembly and valve operation withou

17、t interference. 4. REGULATORY REQUIREMENTS. 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practical, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product conforma

18、nce. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of s

19、uch conformance. 5.2 Market acceptability. The product offered shall be of the latest model of the standard product of the supplier that have been used in the field for at least one year by commercial users. 5.3 Examinations. Each valve examined shall be inspected for compliance with the requirement

20、s specified in 3.1 through 3.14. Nonconformance to any specified requirement, or the presence of one or more defects shall constitute cause for rejection. 6. PACKAGING. 6.1 Preservation, packing, and marking shall be as specified in the contract or purchase order. (see 7.2) 7. NOTES. 7.1 Part identi

21、fication number (PIN). The following part identification numbering procedure is for Government purposes and does not constitute a requirement for the contractor. This example describes a part numbering system for CID A-A-59379 3 Provided by IHSNot for ResaleNo reproduction or networking permitted wi

22、thout license from IHS-,-,-A-A-59379 m 9038054 OOLL332 954 H A-A-59379 AA59379- 1 L 1 - Type I 2 - Type II 3 - Type III 7.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this CID. b. Type of valve required (see 2.1). c. Color of finish requ

23、ired (see 3.14). d. Level of preservation and packing required (see 6.1). 7.3 Data requirements. The contracting officer should include, in the contract or order, any data requirements, such as instructional materials or technical publications to be furnished with the valves. 7.4 Provisioning. The c

24、ontracting officer should include, in the contract or order, provisioning requirements for repair parts (overpack if required) and maintenance tools (including special tools), as necessary, and instructions regarding packaging and shipment of the valves. 7.5 Sources of documents. TTMA RP No. 28 is a

25、vailable from the Truck Trailer Manufacturers Association (TTMA), 1020 Princess Street, Alexandria, VA 223 14. 7.6 Sources of sumlv. Manufacturers whose products meet some or all of the requirements of this CID are listed below; however, competition is not limited to these companies. Milwaukee Valve

26、 Co. Inc. 2375 S Burrell St Milwaukee, W1 53207- 1 5 19 Morrison Bros. Co. 24th E Elm St PO Box 238 Dubuque, IA 52004 Marine and Valve Supply 13 1 15 Braton Rd Unit A Whittier, CA 90605 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7.7 Subiect te

27、rm (key word) listing. Bonnet Double disk Valve body Custodians: Army - AT Navy - MC Preparing Activity: Army - AT (Project 4820-0821) Review Activity: Navy - YD2 Civilian Coordinating Agency GSA - FSS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-