ARMY A-A-59834-2009 ANCHOR ROCK CHOCK《垫块式岩锚》.pdf

1、 A-A-59834 September 25, 2009 COMMERCIAL ITEM DESCRIPTION ANCHOR, ROCK, CHOCK This commercial item description is approved for use by the Defense Supply Center, Philadelphia and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE. This commercial item descript

2、ion covers the requirements for chocks which are used for protecting climbers on steep rock routes by placing the chocks into cracks in the rock. 2. CLASSIFICATION. The chocks will be furnished in the following types and sizes: 2.1 Types Type I Wedge, wired Type II Hexcentric, wired Type III Irregul

3、ar, slung 2.2 Sizing. The chock be as light-weight as possible, while meeting the standards described in the description. Type I - Sizes 1-13 (as specified in Table I) Type II - Sizes 1-11 (as specified in Table II) Type III - Sizes 0.5 3 (as specified in Table III) Comments, suggestions, or questio

4、ns on this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of this address information u

5、sing Acquisition Streamlining and Standardization Information System (ASSIST) online database at http:/assist.daps.dla.mil/. AMSC N/A FSC 8465 METRIC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59834 2 3. SALIENT CHARACTERISTICS. The chock sh

6、all be as light-weight as possible meeting the standards described in 3.1 and provide ease of use with any typical combat gloves. 3.1 Type I (TABLE I). The chock shall be a wedge-shaped design with the chocks width tapering from the top to the bottom and the dimension requirements of drawing X3-3-01

7、15. The chocks thickness shall be tapered from top to bottom along its width. The wire loop shall be routed through four holes in the chock (two in the top, two in the bottom). The size shall be stamped on the wider, flat portion of the chock. The wire loop cable will protrude 190 ( 13) mm on sizes

8、1 through 10; 215 ( 13mm) on sizes 11 through 13. The thickness shall be measured at the top of the chock, along its shorter side. The width shall be measured at the top of the chock, along its longer side. The chock will be constructed and comply with the size requirements in Table I. 3.1.1 Type II

9、 (TABLE II). The chock shall be constructed and comply with the size physical requirements in Table II and the dimension requirements of drawing X3-3-0116. The wire loop shall be routed through four holes in the hexcentric shaped portion (two in the top, two in the bottom). The size shall be stamped

10、 on the hexcentric shaped portion of the chock. The thickness of each hexagonal side shall vary to provide use in various sized cracks in the rock. The wire loop cable shall protrude 190 ( 13) mm on sizes 1 through 5; 342 mm ( 13) mm on sizes 6 through 11. The hexcentrics shall be measured for thick

11、ness on their parallel sides. The length shall be measured at the top along the longest dimension, perpendicular to width measurement. 3.1.2 Type III (TABLE III). The chock shall be constructed and comply with the size and physical requirements in Table III and the dimension requirements of drawing

12、X3-3-0117. The irregular chock shall be constructed to provide three points of contact with the rock. The irregular chock shall be designed to provide protection in both passive and active camming modes. The size shall be depicted on a label that is affixed to the webbing loop portion. The webbing l

13、oop portion shall protrude 190 ( 13) mm on all sizes. The width shall be measured at the point at the end of the rails proximal to the webbing. 3.2 Color. The chocks shall be provided in a low reflectance, matte finish and provide low contrast with typical use terrain. Each size shall be of a differ

14、ent anodized color (Type I and Type II only). The webbing sling (Type III only) shall be of a different color for each size. 3.3 Materials. 3.3.1 Basic Material (All types). The wedging portion of the chock shall be anodized 6061-T6 or 7075 aluminum. Provided by IHSNot for ResaleNo reproduction or n

15、etworking permitted without license from IHS-,-,-A-A-59834 3 TABLE I. Physical characteristics for Type I TABLE II. Physical characteristics for Type II Size Width (mm) Thickness (mm) Wire Diameter (mm) Min. breaking Strength, kN Weight, Grams 1 9.1 4.3 1.5 2 7 2 9.9 4.8 1.7 2 8 3 11.4 6.1 2.2 5 15

16、4 12.4 6.9 2.2 6 16 5 13.5 8.4 2.5 6 18 6 15.5 10.2 3.0 10 32 7 16.3 11.7 3.0 10 34 8 18.3 13.5 3.0 10 37 9 20.8 15.2 3.0 10 39 10 23.4 17.3 3.0 10 43 11 26.7 20.1 3.0 10 51 12 30.5 22.9 3.0 10 58 13 35.1 26.4 3.0 10 71 Tolerance (10%) (10%) 0.1 N/A (10%) Size Width (mm) Thickness (mm) Wire Diameter

17、 (mm) Min. breaking Strength, kN Weight, Grams 1 19.0 11.4 2.38 6 19 2 20.8 14.2 2.38 6 22 3 24.4 16.8 2.38 6 28 4 27.9 20.6 3.17 10.0 51 5 33.0 23.9 3.17 10.0 53 6 39.1 27.2 3.17 10.0 64 7 45.7 33.0 3.17 10.0 86 8 54.1 39.1 3.17 10.0 94 9 63.7 47.0 3.17 10.0 124 10 75.2 55.6 3.17 10.0 164 11 89.1 6

18、5.0 3.17 10.0 206 Tolerance (10%) (10%) 0.1 N/A (10%) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59834 4 TABLE III. Physical characteristics for Type III 3.3.2 Sling/Cable Material 3.3.2.1 Type I & Type II. The wired portion of the chock sha

19、ll be either galvanized or stainless steel. 3.3.2.2 Type III. The sling portion of the chock shall be either Dyneema or nylon (see 7.4). 3.4 Tests. The chock shall meet Union Internationale des Association dAlpinisme (UIAA) Standard 124 or European Standard EN 12270. 3.5 Workmanship. The finished an

20、chor rock chock shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the contractors own quality assurance standards and the quality assurance standards defined in the technical data in the solicitation and/or contract. 4. REGULATORY REQUIR

21、EMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally prefer

22、able materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet

23、 the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conf

24、ormance. 5.2 Visual examination. Each chock shall be examined for the following defects as listed in Table IV. Size Minimum range, mm Maximum range, mm CAM Width, mm Min. breaking Strength, kN Weight, grams 0.5 16 28 28 9 26 1 20 30 28 9 35 1.5 26 38 28 14 50 2 29 41 31 14 55 2.5 32 48 31 17 77 3 38

25、 54 31 17 90 Tolerance N/A N/A 0.1 N/A (10%) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59834 5 TABLE IV. End item examination Examine Defect Description Finish Not smooth and adherent Construction Not free of burrs, rough spots, slivers, fl

26、at areas or projections Any component loose, missing or not specified type Any component fractured, slit, punctured, dented, bowed, malformed or damaged Marking etched or indented, contains rough or sharp edges Label and instruction slip Incorrect, illegible, omitted or misplaced. Marking Omitted, m

27、issing information or illegible Swage (Type I & II) Not swaged properly Not covered Webbing or Wire Loop Not sized properly 5.3 Acceptance criteria. Acceptance criteria shall be as specified in the contract or purchase order (see 7.5). 6. PACKAGING. 6.1 Preservation, packing and marking. The preserv

28、ation, packing and marking shall be as specified in the contract or order (see 7.5). 7. NOTES. 7.1 Sources of Government documents. 7.1.1 Copies of Government documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Documents Order Desk, Building 4D, 700 R

29、obbins Avenue, Philadelphia, PA 19111-5094. 7.1.2 DRAWINGS U.S. ARMY NATICK SOLDIER CENTER 3-3-0115 Anchor, Rock, Chock, Type I 3-3-0116 Anchor, Rock, Chock, Type II 3-3-0117 Anchor, Rock, Chock, Type III (Copies of drawings are available from the U.S. Army Research Development and Engineering Comma

30、nd, Natick Soldier Center, ATTN: NSRDEC-RDNS-WPW-C), Kansas Street, Natick, MA 01760) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59834 6 7.2 Non-Government Documents. Non-Government standards and other publications are normally available fro

31、m the organizations that prepare or distribute the documents. These documents may be available in or through libraries or other informational services. EUROPEAN STANDARD (EN) EN 12270:1998 Mountaineering Equipment Chocks Safety Requirements and Test Methods (Copies are available online at www.bsi- o

32、r from BSI British Standards, Customer Services 389 Chiswick High Road London W4 4AL United Kingdom) INTERNATIONAL MOUNTAINEERING AND CLIMBING FEDERATION UNION INTERNATIONALE DES ASSSOCIATIONS DALPINISME (UIAA) UIAA Safety Standard 124 Mountaineering and Climbing Equipment, Chocks (Copies are availa

33、ble online at www.theuiaa.org or from the Union Internationale Des Associations DAlpinisme (UIAA) Monbijoustrasse 61 Postfach CH-3000 Bern 23 Switzerland 7.3. Federal Acquisition Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of Documents

34、 at 202-512-1800. 7.4 Available sources. Dyneema or equal. (Head office address: Mauritslaan 49, Urmond, P.O. Box 1163, 6160 BD Geleen, the Netherlands or Production site address: Eisterweg 3, Heerlen, P.O. Box 6510, 6401 JH Heerlen, the Netherlands ) 7.5 Ordering Data. The contract or order should

35、specify the following: a. Commercial Item Description document number b. Type and size required (see 2.1). c. Acceptance criteria (see 5.3). d. Packaging (see 6.1). MILITARY INTERESTS: CIVIL AGENCY COORDINATION ACTIVITY: Custodian: PREPARING ACTIVITY: Army - GL GL-Army Marine Corps - MC Project 8465

36、-2009-014 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-