ARMY DOD-C-63976 (5)-1994 CASE CARTRIDGE 30MM AMMUNITION FOR M788 M789 AND M799 SERIES OF 30MM AMMUNITION《M788 M789及M799系列30mm炮弹筒》.pdf

1、. DOD-C-63976 (5 1 m 9999906 2042934 232 m 3 METRIC DOD-C-63976 (AR) AMENDMENT 5 29 November 1994 SUPERSEDING AMENDMENT 4 30 March 1989 a MILITARY SPECIFICATION CASE, CARTRIDGE, 30MM AMMUNITION FOR “88, M789 AND M799 SERIES OF 30MM AMMUNITION This amendment forms a part of DOD-C-63976 (AR), dated 14

2、 May 1982, and is approved for use by the US Army Armament Research, Development and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 2.1.1: Add “MIL-STD-1235 - Single and Multi-Level Continuous Sampling Procedures and Tables for Inspe

3、ction by Attributes“ to the end of the paritgraph. Delete: “FED-STD-115“ and substitute “FED-STD-151“. 2.1.2: Under “3rawings“ : Delete? “11825969 - Test Barrel, 30mm Mann (6.5)“ and substitute “9390627 - Barrel, Test 30mm (ADEN. Barrel)“ Add dwg: “9390748 - Barrel, Test: Gun, M230, 30mm (Progressiv

4、e w/6.5 degree exit twist)“ 3.2.1: Delete in its entirety and substitute the f.ollowing: “3.2.1 Performance. The cartridge case shall meet the following performance requirements when assembled in a 30mm target practice cartridge as shown on Drawing 11825947. Unless otherwise specified, performance r

5、equirement involving the firing of the cartridge apply when fired in a test barrel conforming to Drawing 9390748.“ 1 of 5 FSC 1305 -I,-.- fii*-z ?; , A ,-sA31BUTIGN STATEMENT A. Approved for public release; distribution is unlimited. _- ?.- Provided by IHSNot for ResaleNo reproduction or networking

6、permitted without license from IHS-,-,- DOD-C-b397b (5 1 W 9999906 2042935 179 W DOD-C-63976 (AR) AMENDMENT 5 3.2.l.: Delete in its entirety and substitute the following: “3.2.1.1 Case rupture When fired under the conditions of 3.2.1, the case shall not rupture. It shall also not rupture when assemb

7、led in specially loaded cartridges and subjected to an over-pressure condition from 395 to 430 MPa.“ PAGE 5 Note 1/: Delete “4.5.3.10.2“ and substitute “4.5.3.10.1“. PAGE 8 3.2.3.1.3: Delete “MIL-STD-331, Method 107“ and substitute “MILSTD-810, Method 509“. PAGE 12 TaD?e III: Delete sample Size “20“

8、 and substitute “Sample size “60“ for case extraction“. PAGE 13 4.4.22: Add at the end of the sentence “or MIL-STD-1235“. PAGE 14 4.4.2.2.: Delete “3/“ from Major 104 and add “31“ to Majors 101, 102, 103. PAGE 15 4.4.2.1, Minor 222: Delete “3.3.3“ and substitute “3.5“ PAGE 16 Note 2: Delete “min. sa

9、mple size 315 no defects allowed“ and substitute “Sample size determined by .25 AQL (315 min sample size) zero defects al iowed . I PAGE 20 4.5.1.1: Delete ir! its entirety and substitute the following: “4.5.1.1 Case rupture. The round shall be fired in a testbarrel which conforms to drawing 9390748

10、. The case shall be visually examined for evidence of case rupture. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DOD-C-6377b (5) 7777706 2042736 005 DOD-C-63976 (AR) AMENDMENT 5 4.5.1.5.1: Delete in its entirety and substitute the following: “4.5.

11、1.1 Chamber over-pressure Special test rounds shall be cssembled ir. which the propellant load is such that the chamber pressure, measured at the case mouth, is within the range of 395 to 430 MPa. The rgund shall be fired in a test barrel (Dwg 9390748). The cartridge cases shall be examined for evid

12、ence of case rupture. The case shall be cmsidered to have failed if it ruptures at a pressure of less than 430 Mla. Cases tested at pressure in excess of 395 MPa shall be considered a success if no failure occurs and will be considered a no-test if failure occurs at pressures above 430 MPa.“ PAGE 21

13、 4.5.2.3: Delete “MIL-STD-331 test method 107“ and substitute “MIL-STD-810 c2st meKnod 509 (Slight Mouth Erosion Permissible) Delete “4.3.2“ and substitute “4.5.3“ PAGE 22 4.5.3.4.1, third sentence: Delete “hole“ and substitute “hold“. Delete last sentence of last paragraph and substitute “All mecha

14、nical ?roperties test results shall be reported.“ PAGE 23 4.5.3.4.2, third sentence: Delete “avoided“ and substitute avoided“ 9eiete last sentence and substitute “All hardness test results shall be reG c I t Ed “ . PAGE 24 4.5.3.5: Delete last sentence and substitute “The thickness values obtained b

15、y both methods should be reported.“ 4.5.3.4.2: Delete last sentence and substitute “The coating weight data cis.ained wi 11 be reported. I 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- DOD-C-63976 (5) 9 9999906 DOD-C-63976 (AR) AMENDMENT 5 20429

16、37 T4L PAGE 25 4.5.3. E: Delete “3.5.3“ and substitute “3.5“. D 3 4.5.3.7.1: Delete in its entirety and substitute the following. *,4.5.3.7.1: External defects, case sidewall. Examination of the case sidewall for longitudinal cracks or seams shall be performed using the five diopter magnifier or a (

17、NDT) device capable of detecting external cracks or seams. examined for random gross defects. When using the optical method, adequate lighting must be available and higher magnification can be used to differentiate between a scratch or a crack. When it is still questionable whether or not a crack ex

18、ists, then die penetrant testing per MIL-16866 can be employed. Any case found to have a crack in excess of 38.1 mm long by .19mm deep shall be considered as a defect. The cross sectioning technique may be used to verify the depth of a crack identified visually. Prior to the examination the entire s

19、urface of each case will be When a (NDT) method is used, sufficient standards will be available to verify that cracks or seams in excess of .19m deep by 6mm long can be reliably identified. Any cracks or seams in excess of 19mm deep by 6mm long shall be considered as defects. 1c the NDT technique sh

20、all extend from 15-25mm to 85.00mm when measured from tne head end of the case.“ The area of inspection to be included PAGE 26 4.5.3.7.2: Delete “Binocular microscope using a minimum of 7x magnification“ s:5 subsrituta “five diopter magnifier“. Delete “Refer to 6.7“ from the end of paragraph 1 and a

21、dd “Refer to 6.7“ tC the end of the second paragraph. . 4.5.3.7.3, last sentence, second paragraph: Delete “For definition, refer to 6.3.7“. _. 4.5.3.8: Delete last sentence and substitute “The individual values thus obtained shall be reported.“ PAGE 27 4.5.3.10: Delete “6.3.8“ and substitute “6.8“.

22、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- DOD-C-63976 (5) 9999906 2042938 988 M DOD-C-63976 (AR) AMENDMENT 5 PAGE 29 * 5.3: Ad6 smtence to the end of paragraph as follows: “The letter of submittal shall state contractor, contract number, spec

23、ificacion number, item nomenclature and classification of defects or test paragraph.“ Delete “DRDAR-QAF-I“ and substitute “AMSTA-AR-QAC-C“. 6.5: Delete in 11s entirety and substitute the following: “6.5 Data report. All data obtained from testing as described in 4.4.3.4 and 4.4.3.6 shall be reported

24、.“ 5.7: Delete first sentence and substitute “The contractor and supplier shall establish defect standards for use in the NDT test defined in 4.3.3.7.1, 4.3.3.7.2 and 4.3.3.7.3.“ PAGE 30 E. 1; : Delete “4.3.4“ and substitute “4.5.1 and 4.5.2“ 6.11: Delete in its entirety i; _._ & margim of this amen

25、dment are marked with an asterisk or vertical lines *y- :-A, rn the previous amendment were made. This was done as a convenience only Indicate where changes (additions,. modifications, corrections, deletions) 2715 ch? Government assumes no liability whatsoever for any inaccuracies in ihese notations

26、. Bidders and contractors are cautioned to evaluate the reqAirernencs of this document based on the entire content irrespective of the rxargiml notations and relationship to the last previous amendment. Cdstodian: Army -AR Preparing activity: Army - AR ( Pro ec t 13 O 5 -AE88 ) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-