ARMY MIL-A-71180-1993 ADAPTER METAL PALLET《金属托盘适配器》.pdf

1、MIL-A-7lili60 9999906 1948749 bb9 MIL-A-71 c80 (AR) 15 June 1993 MILITARY SPECIFICATION ADAPTER, METAL PALLET This specification is approved for use by the U.S. Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Department of Defense. 1. SC

2、OPE 1.1 Scope. This specification covers the requirements, examinations, tests and packaging of special adapters for metal pallets. The adapter, together with the metal pallet, will be used in unitizing ammunition (see 6.1). 1.2 Classification. The adapters shall be of the following types (see 6.1):

3、 Type I - Adapter, Pallet, TOW 2A Container 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

4、these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving t

5、his document, should be addressed to: Commander, U.S. Army ARDEC, ATN: SMCAR-BAC-S, Picatinny Arsenal, NJ 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8140 ON STATEMENT 4, Approved for public rel

6、ease; distribution is unlimited. O Licensed by Information Handling ServicesMIL-A-71L80 9999906 1948750 380 SPECIFICATIONS FEDERAL TT-C-490 - MILITARY MIL-A-48078 - MIL-A-70625 - STANDARDS MILITARY MIL-STD-109 - MIL-STD-I 71 - MIL-STD-1261 - MIL-STD-1660 - MIL-A-71180 (AR) Cleaning Methods for ferro

7、us Surfaces and Pretreatments for Organic Coatings Ammunition, Standard Quality Assurance Provisions, General Specification for Automated Acceptance Inspection Equipment Design, Testing and Approval of Quality Assurance Terms and Definitions. Finishing of Metal and Wood Surfaces Arc Welding Procedur

8、es for Constructional Steel Design Criteria for Ammunition Unit Loads (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2

9、 Other Government documents, drawings, and publications. The f o1 lowing other Government documents, drawinss, and publications form a part of this document to the-extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS U.S. ARMY ARMAMENTS RESEAR

10、CH, DEVELOPMENT AND ENGINEERING CENTER ( ARDEC ) ACV0018 8 - Combination of Adopted Items, Pallet and Pallet Adapter, Unitization of TOW 2A Container Container ACV00189 - Top Assembly, Pallet Adapter TOW SA 2 Licensed by Information Handling ServicesMIL-A-73380 9999906 3948753 237 MIL-A-71180 (AR) A

11、CV0019 O - Bottom Assembly, Pallet Adapter TOW 2A AC200000423 - Chemical Agent Resistant Coating (CARC) Container Finishing Requirements for Metal Pallets and/or Pallet Adapters (Copies of other Government documents, drawings, and publications required by contractors in connection with specific acqu

12、isition functions should be obtained from the contracting activity or as directed by the contracting activity. ) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are D

13、oD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D39 51 - Standard

14、 Practice for Commercial Packaging (DOD adopted) (Applications for copies for ASTM publications should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 191 03. ) 2.3 Order of precedence. In the event of a conflict between the text of this document an

15、d the references cited herein (except for related associated detail specifications, specification shets or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIR

16、EMENTS 3.1 Materials. Materials and parts shall be in accordance with applicable drawings and specifications. 3.2 Adapters. The adapter assemblies shall comply with all requirements specified on drawings (Dwgs) ACV00189, ACV00190, as applicable and associated drawings and with all requirements speci

17、fied in applicable specifications and standards. 3.3 Welding. The welding shall comply with the requirements of MIL-STD-1261. 3 Licensed by Information Handling ServicesMIL-A-7LLBO 999990b MIL-A-71 180 1948752 153 3.4 Unit load tests. The metal pallet adapters, as part of unit loaded pallets, shall

18、conform to the requirements specified in MIL-STD-1650. 3.5 First article inspection. When specified in the contract or purchase order (see 6.2), a sample shall be subjected to first article inspection in accordance with the technical provisions herein (see 4.3). 3.6 Workmanship. 3.6.1 Adapters. The

19、adapters shall be regular, smooth and free from wrinkles, cracks, rough spots, burrs, sharp edges and other defects that might affect the serviceability, durability and safety of the adapters. Weld spatter is permissible on non-load bearing surfaces provided it is firmly attached. 3.6.2 Paint coatin

20、g. The finished coat shall cover all required surfaces and be continuous. Paint runs are permissible provided they are no more than 3 inches in length, solid and free from cracks and blisters. Excess thickness is acceptable in areas where multiple passes of the paint gun are required to obtain total

21、 coverage. Paint chips which expose primer or bare metal are acceptable provided they are not more than 0.25 inches in diameter and no more than two such paint chips on an adapter. Scratches which expose primer or bare metal are permissible provided the are no more than 1.5 inches in length and no m

22、ore than 10 inches total on an adapter. Bare metal on contact surfaces in areas inaccessible to paint is permissible. 3.6.3 Parts. All parts shall be free of chips, dirt, grease, rust and foreign material. The cleaning method used shall not be injurious to any of the parts nor shall any of the parts

23、 be contaminated by the cleaning agents used. 4. QUALITY ASSURANCE PROVISIONS 4.1. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herei

24、n. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspe

25、ctions set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4 Licensed by Information Handling ServicesMIL-A-7LLO 9999906 1948753 09T MIL-A-71180 (AR) 4.1.1 Responsibility for compliance. All items shall meet

26、all requirements of Sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products

27、or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material,

28、either indicated or actual, nor does it commit the Government to accept defective material. The absence of any 4.1.2. General provisions. Unless otherwise specified herein, the provisions of MIL-A-48078 apply and form a part of this specification. Reference shall be made to MIL-STD-109 to define qua

29、lity assurance terms used herein. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (see 4.4). 4.3 First article inspection. 4.3.1 Submission. The contractor shall submit

30、 a first article sample as designated by the Contracting Officer for evaluation in accordance with prcvisions of 4.3.2. The first article sample shall consist of the assemblies, components and test specimens listed below in the quantities indicated. Part description Top assembly (unpainted) Bottom a

31、ssembly (unpainted) Top assembly (painted) Bottom assembly (painted) Quantity The samples for the adapter assemblies may be comprised of the individual painted top and bottom (when applicable) assemblies submitted. 5 Licensed by Information Handling ServicesMIL-A-IJLBO 9999906 1948754 T2b MIL-A-71.1

32、8 O (AR) 4.3.2 Inspections to be performed. As determined by the Government, the first article assemblies, components and test specimens may be subjected to any or all of the examinations and tests specified in this detail specification and be inspected for compliance with any or .all requirements

33、of the applicable drawings. 4.3.3 Rejection. See MIL-A-48078. 6 Licensed by Information Handling ServicesMIL-A-71180 7777906 1748755 962 O Cn rl O O u 4 a al 4J -4 L 40 nw E (B o 4 LL O .-I E I ul - I) ci c al c O a E O u a c a (B a, -4 I+ E al Lo 5LI) =A - Cm ci av pia, cw la, Tl Xk oc (Bo -4 au a

34、Er= vi GE: 4a ox mw W V a w ki LL O cn d O O u 4 a cic, -4 . AO E nw I) o d O I c W I 0)Lo GV a, mw pia, a nk a,c mo -4 au m EC -4 +JE c,a ox mw Z I- V W In 0 a z -ri c h de ao E a I- I- w a 0 O z I- I W w aal pia 7k O -ici -.-i a, ma we -i E aa ox EW n N m -3 A N N N (u w -3 -3 -3 -3 !n -3 -3 -3 -3

35、 w . . . . . . (u (u cv cv io m m rn m m rl rl rl 4 rl cn CO rl O O u 4 a a, +J c -4 a n a E a, 0 LI) r6 O E 4 a Lo e, V al CI al 0 k O CI c O .-i ci m c ri E r6 X u . .- v, W 8 7 Licensed by Information Handling ServicesMIL-A-7LLBO = 9999906 L94B75b T9 MIL-A-71180 (AR) 4.4 Quality conformance inspe

36、ction. 4.4.1 Inspection lot formation. The term “inspection lot“ is defined as a homogeneous collection of units of product from which a representative sample is drawn or which is inspected 100 percent to determine conformance with applicable requirements. Units of product selected for inspection sh

37、all represent only the inspection lot from which they are drawn and shall not be construed to represent any prior or subsequent quantities presented for inspection. Homogeneity shall be considered to exist provided the inspection lot has been produced by one manufacturer, in one unchanged process, u

38、sing the same materials and methods, in accordance with the same drawings, same drawing revisions, same specifications and same specification revisions. All material submitted for inspection in accordance with this specification shall comply with the homogeneity criteria specified herein, regardless

39、 of the type of inspection procedure which is being applied to determine conformance with requirements. 4.4.2 Examinations and tests. a. Classification of characteristics. Quality conformance examinations and tests are specified in the following Classification of Characteristics paragraphs. The cont

40、ractors quality program or detailed inspection system shall provide assurance of compliance of all characteristics with the applicable drawing and specification requirements utilizing as a minimum the conformance criteria specified. When cited herein, attributes sampling inspection shall be conducte

41、d in accordance with Table II below, using the inspection levels stated in the Classification of Characteristics paragraphs. 8 Licensed by Information Handling ServicesMIL-A-71180 9999906 1948757 735 TABLE Lot Size 2 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501. to 120

42、0 1201 to 3200 3201. to 10000 10001 to 35000 35001 to 150000 150001 to 500000 500001 and over MIL-A-71180 (AR) II. Attributes sampling inspection Inspection Levels * * * * * 1250 1.250 1250 3 250 1250 1250 125 125 125 1 25 125 125 315 31 5 500 500 * * * 32 32 32 32 32 80 80 1.2 5 125 125 200 200 * 1

43、3 1. 3 1.3 1. 3 13 30 30 50 50 50 80 80 125 3 25 5 5 5 5 1.3 13 20 20 20 32 32 50 50 50 50 VI 3 3 3 3 5 5 8 13 13 13 1.3 13 13 13 a Numbers under inspection levels indicate sample size; asterisks (*) indicate one hundred percent inspection. If sample size exceeds lot size, perform one hundred percen

44、t inspection. Accept on zero and reject on one or more for all inspection levels. b. Alternative quality conformance provisions. Unless otherwise specified herein or provided for in the contract, alternative quality conformance procedures, methods or equipment, such as statistical process control, t

45、ool control, other types of sampling plans, etc., may be used by the contractor when they provide, as a minimum, the level of quality assurance required by the provisions he.rein. Prior to applying such alternative procedures, methods or equipment, the contractor shall describe them in a written pro

46、posal submitted to the Government for evaluation (see 6.3). When required, the contractor shall demonstrate that the effectiveness of each proposed alternative is equal to or better than the specified quality conformance provision(s) herein. In case of di-spute as to whether the contractors proposed

47、 alternati.ve(s) provides equivalent assurance, the provisions of this specification shall apply. All approved alternative provisions shall be specifically incorporated into the contractors qua1i.t.y program or i.nspect:ion system, as applicable. 9 Licensed by Information Handling ServicesMIL-A-7118

48、0 = 9999906 1948758 671 m J a Q) 4 c .ri m a c - . h a E Q) ci) ci) 4 a O h d ID (u WNN ID. em . m mmm m 0 c O z a -4 G LI) c m E x k O 3 k O O a ici O Q) u c Q) a -4 ? w 10 Licensed by Information Handling ServicesMIL-A-7IIIIBO = 9999906 II948759 508 w I e r + X U z I 4 L O 4 I- W m r a a, c, c -4

49、m pi h Q E a, m m 4 a =o EE 4 d - W O z W u W LL W u cl O I c W I z I- V W ln 0 a z rl d m N mln w m mm m . . *. a, k O 4 u a k k O u c *d 0 c -4 m cn -4 . 10 rw a, O E Q)c a, u c a, 5 w m Co a, Cl x u c 4J k a, E .rl k a a, c E-i 6i I= .ri ci m O u u P; 4 u k O 44 . am aa, mci Ga) oc, a, a,Q C 11 Licensed by Information Handling Services5 a, ci c *ri m a C 3 h Q E a, Lo In 4 E O &, ci iLJ0 . d cm c -m W N NNN W. e m m mmm m m- a .ri rc Ln C m E A k 3 k O k 12 Licensed by Information Handling Services. MIL-A-7LLO H 77777Ob 1948761 Lbb D 4 LA. O ti W I ln a a, ci C -4 a !a h