ARMY MIL-B-313 A-1953 BOTTLES AND FILLED VIALS FOR CHEMICAL DETECTOR KITS《用于化学检测试剂盒的瓶和填充瓶》.pdf

1、ItL August 1953 . SUPERCmING JAN-B-313 . lh October 19L8 MILITARY SPECIFICATION BOTTLZS AND PIUE VIAISp . FOR Ci%MIcHL DETECTOR KIIS 1, SCOPE 12 Tes specification covers unfilled bottles and reagat-fiUed vials for use in chemical detector kits. 2. APPLICABLE SPlXIFICATIONS, STAM)HRDs, DRAWINGS, AND

2、PUBLICATIGNS 23 The folowing specifications, stanaards, and drawings. of the issue in effect on date of invitation for bids, form a part of this sped- ficati on : . .c. -I .- IL+-ll6 = Preservationj Methods of. M.EL-P-3Il - Pump, Air*amping, 9. MIL-P-10576 C. Packaging of Chemical Corps. Spare.Parts

3、 ar MIL-P-10577 - Packaging of Components and Subassemblies, MfL-C-l2?!b - Clips, Sampling and Detector Tubes Accessories, General Specifiction, Dornestic Shipment to Assembly Plants. (For Chemical Agent Getection) . Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

4、e from IHS-,-,-MILITARY CHUTCAL COWS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-302 Vials.- The vials shall be manufactured as specified on thela respective drawings, as follows 8 Vial, - DPawing No. 3.2.1 Emme1 adhesion.- The enamel coating sha

5、ll not rub off when tested a8 specified in 4.4.l. as speciiidA .3. perform satisfactoriy when tested as specified in 4.4.4, paper when tested as specified in 4.4.4.2.3, 3.2,2 Leah e,- The vial assemblies shall not leak when tested 3.2.3 %agent performancer Reagents contained in the *als shall 3.2.3.

6、1 3.3 Workmanship.- Bottles and vials shall be properly finished and Red vial reagent shall cause no discoloration of filter annealed, free from imperfections which impair their strength car service- ability, and clean and dry. 4, SAMPLING, INSPECTION, AND “ST PFU)CEDLRESF 4.1 Lot. b.l.1 Bottles,- A

7、 lot of each type of bottle shall consist of the quantity produced by one manufacturer under essentially the same.manu- facturing conditions. within the above limitations, shall be debignated by the Inspetor, The inspection lot for nondestructive inspection,- 4.1.2 Filled vials,- A lot of each type

8、of filled vial shall con= sist of the quantityproducea by one manufacturer under essentially the same mandactuling conditions, and filled with not more than one batch of reagent (see 6,3). within the above limitations, shall be designated by the inspector. 4.2 Sampling, The inspection lot for nondes

9、tructive inspection, bo2d For nondestructive inspsction.- Sampling for nondestructive inspection shall. be conducted in accordance with 4.3.3 and Standard Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4d.2 For tests*- (see 6.6). 4,2,2a F?P A repres

10、entakive sample of 20 dropper bulbs, ten for test, and ten for retest, shall .be selected at random from each lot for the tests specified in 46.2, 4,2*2*2 For reagent, pebformance %es-r Samples shall be selected at rariaom from each lot for reagent perfissybanee tests as specalfied %n Table I, Table

11、 I No. of dds in lot NO* of-vials to. be tested t up tJ m t 1 io1 - Vial cracked or broken 2. Vial length and diameter-incorrect 3. Filling missing or incorrect 4. cork missing, amaged, or incorrect fit 5. Coating missing or incorrect color Minor AQL 2.5 percent 5le Marking missing, illegible, or in

12、correct Contamination Incidental None Categories and defects la, Leakage place the aropper bulb in a cry-air oven with forced circulation at 1% for 70 hou At the end of this period, remove the bulb and allow to remain at roan temperature for 16 to 48 hours* Perform the leakage te76. 5.2 For shipent

13、as spare partsr- The bottles anci fillea vials shall 6, NOTE 6.1 Intended use,- The bottles and filled vials covered by this I I specification are intentied for use in dkttctor kiSs for the dstection of chemical agen%s in the field. 6.2 Ordering data,- Procurement aocumsnts should specify: a, be Tit

14、le, number, ana date of this speci*ica%on, Type of packoging and packing requii.ed (ste section 5). 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BIL-B313A(onf.C) 6.3 Batche- I baSch is defined as that quantity of matesid which has been subjected

15、 %Q some unit chemical9 or phpiCa31 &ng process intended to mke %he f%d. pr.euc% uniform. 6& Precautions.- Adequab precautions should be taken En %he handling of HN-1 solution. The test in 4.4&,2*3 should be carried out Bn a. %zell-venKlated funje hood. If “-3. QC “-1 solut&Qn should be spilled on t

16、he clothing or skin, 4EUXFELY wash the contaminated area thoroughly with hot, soapy water. t 6,6 Samrrpling and testing.- men the contractor consistently produces high-quality material and operates under a system of quality control accept- able to the Governnient, the Government at its discretion, m

17、ay modify, in whole or in part, the ssmpling and testing procedures specified herein. However, %he Government reserves the right to return at any %We, with- out previous notice to the contractor, to the sampling and testing procedume specified herein, at any time, without previous notice to the contractor, to the sapzng and testing procedures specified in this specification. Aowgver, the Governmnt reserves the right to return 6,7 HN-le “-1 may be obtained from the Chemical Corpse 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-