ARMY MIL-C-14747-1968 CARTRIDGE 105MM APERS-T M494 FOR 105MM GUN M68 LOADING ASSEMBLING AND PACKING《M494型105MM枪M68杀伤性子弹组装和包装》.pdf

1、MIL-C-14747 13 W 77777Ob O4b4b 4 I _ MIL-C-14747 (MU) -. , , -_ I *. a . .-* 11 July 1968 MILITARY SPECIFICATION CARTRIDGE, 105MM: APERS-T, XM494E3 FOR 105MM GUN M68 LOADING, ASSEMBLING AND PACKING 1. SCOPE 1.1 This specification covers the loading, assembling and packing for one type of cartridge d

2、esignated as Cartridge, 105MM: APERS-T, XM494E3. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bibs or request for proposals form a part of this specification to the.extent specified herein. SPECIFICATIONS MILITARY MIL-A-2550 MIL-1-45607 - Inspe

3、ction Equipment, Supply and - Ammunition and Special Weapons, General Specification for Maintenance of STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (ABC-STD-105) MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-414 - Sampling Procedures an

4、d Tables for Inspection by Variables for Percent Defective MIL-STD-1168 - Lot Numbering of Ammunition MIL-STD-IS35 - Single and Multilevel Continuous Sampling Procedures and Tables for Inspections by Attributes IFSC: 13151 ! Provided by IHSNot for ResaleNo reproduction or networking permitted withou

5、t license from IHS-,-,-I * MIL-C-14747 13 m 797770b 04b4700 7 m MIL-(2-14747 (MU) ff DRAWINGS ARMY 9204453 - Container, Ammo., Fiber, M563, for 9204454 - Box, Packing, Ammunition, for Cartridge, 9229962 - Cartridge, 105ME1, APERS-T, XM494E3 9229964 - Projectile, 105MM, XM603EL Loading Assembly Cartr

6、idge, 105MM: APERS-T, XM494E3 for Gun M68 105MM, APERS-T, XM49433 for Gun 1468, in Fiber Container, M563 PUBLICATIONS ARMY t ET-9229962 - Equipment. Tabulation (Copies of specifications, standards, drawings and publications required by contractors in connection with specific procurement functions sh

7、ould be obtained from the procuring activity or as directed by the contracting officer.) / 3. REQUIREMENTS 3.1 3.2 Material.-Materials ad parts shall be in accordance Cartridges.-The cartridges shall comply with all with applicable drawings and specifications. requirements specified on Drawing (dwg.

8、) 9229962 and with all requirements specified in applicable specifications. 3.3 Propellant iiieight.-The weight of the propellant shall not differ by more thlm plus or minus 0.25 ounce avoirdupois from that designated .y the loading authorization for the particular lot of propellant used. following

9、requirements when tested as specified in 4.3.5. 3.4.1 Functioning.-The projectile shall exhibit satisfactory first function a minimum of 270 meters from the muzzle of the weapon and shall exhibit a satisfactory second function . 3.4 Proving ground.-The cartridge shall comply with the 2 Provided by I

10、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-Lq747 13 777970b 04b1170L 7 _ - - - MIL-C-14747 (MU) * 3.4.2 Muzzle velocity.-The corrected muzzle velocity of the cartridge, when tested at ambient temperature, shall not be more than 2730 feet per second (f

11、.p.s.) nor less than 2670 f.p.s. and the standard deviation shall not exceed 10.9 f.p.s. 3.4.3 Tracer functioning.-The tracer shall ignite and there shall be visible evidence of burning of the tracer composition to the point of fuze function. 3.4.4 Dye marker.-The functioning point of the projectile

12、 shall be clearly observable from the gun position by satisfactory dispersion of the dye marker. 3.4.5 Security.-There shall be no indication of metal parts separation in the gun bore or in flight prior to fuze functioning. 3.5 Workmanship 3.5.1 All parts and assemblies shall be fabricated and finis

13、hed in a thorough, workmanlike manner. All parts shall be free of chips, dirt, grease, rust and other foreign material. The cleaning method shall not be injurious to any of the parts nor shall the parts be contaminated by the cleaning agents. 3.5.2 assembling contractor on any components furnished t

14、o him painted and marked, when such painting and markings have been marred or obliterated. The painting and marking shall be restored by the 3.5.3 Rotating bands.-Care shall be exercised at all times so that the rotating bands of the projectile are not nicked, burred or otherwise damaged. 3.5.4 Adle

15、sive on threads.-Threads shall be clean and free of contaminant prior to the application of an adequate amount of thread adhesive. An adequate amount of adhesive consists of a quantity of adhesive present on the unengaged thread sufficient to cover at least 80 percent of the threaded surfaces after

16、they are fully engaged and then disengaged as indicated by visual inspection (see 4.3.4). 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.-Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as

17、 specified 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-ILl7Ll7 13 799970b 0Llb4702 O MIL-C-14747 (MU) herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the pe

18、rformance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requir

19、ements. Reference shall be made to Standard MIL-STD-109 in order to define terms used herein. The provisions of Specification MIL- A-2550 shall apply. 4.1.1 Submission of product.-At the time the completed lot of product is submitted to the Government for acceptance, the contractor shall supply the

20、following information accompanied by a certificate which attests that the information provided is correct and applicable to the product being submitted: a. A statement that the lot complies with all of the quality assurance provisions specified within this specification. b. Number of units of produc

21、t inspected. c. Results obtained, by defect code, for all inspections performed . d. Drawing, specification number and date, together with an identification and date of changes. e. Certificates of conformance on all material purchased by the contractor when such material is controlled by Government

22、or commercial specifications referenced in any of the contractual documents . b f. Number of items in the lot. g. Date submitted. The certificate shall be signed by a responsible agent of the certifying organization. The initial certificate submitted shall be substantiated by evidence of the agents

23、authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certificates unless, during the course of the contract, this rathority is vested in another agent of the Cer tif ying organi zatio; . 4.2 Inspection Provisions 4.2.1 Lot formation.-The term “

24、lot“ as used throughout this specification refers to an inspection lot, which is defined as an essentially homogeneous collection of units of product from which a representative sample is drawn and inspected to determine conformance of the lot with applicable requirements. The sample selected shall

25、represent only that quantity of units from which the sample was drawn and shall not be construed to represent any prior or subsequent quantities presented for inspection. Homogeneity shall be considered to exist provided the lot has been produced by one manufacturer in one unchanged process, in acco

26、rdance with the same drawings, same drawing 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14747 (MU) revisions, same specifications and same specification revisions. Changes to the process, specification, or drawings not affecting safety, p

27、erformance, interchangeability, or storage, as determined by the Government, shall not be deemed to alter the homogeneity of the lot. Inspection lots shall comply with MIL-STD-105. Unless otherwise approved by the contracting officer, the inspection lot size of end items deliverable under the contra

28、ct shall be not less than the smallest weekly estimate of quantities contractually scheduled for production during the contract period nor more than the largest monthly quantity contractually scheduled for delivery during the contract period. lots of components or subassemblies, other than the items

29、 of delivery, shall be homogeneous and of a size mutually con- venient to both the contractor and the Government inspector. Lot numbering, as required, shall be in accordance with MIL- STD-1168. Each lot shall contain: a. Projectile metal parts of one lot interfix number from one manufacturer. b. ma

30、nufacturer in accordance with the same drawing revision, same specification and specification revision. manufacturer. manufacturer. manufacturer. manufacturer. manufacturer. Inspection Cartridge cases of one type of metal from one C. Propellant from not more than one lot. d. Loaded fuzes of one lot

31、interfix number from one e. Loaded primers of one lot interfix number from one f. Loaded relays of one lot interfix number from one g. Loaded detonators of one lot interfix number from one h, Loaded tracers of one lot interfix number from one 4.2.2 Examination.-Inspection for Critical defects (and M

32、ajor defects, when so specified), shall be 100 percent. Sampling plans and procedures for Major and Minor defects shall be in accordance with MIL-STD-105 except that continuous sampling plans in accordance with MIL-STD-1235 may be used if approved by the procuring activity. Also, at the option of th

33、e procuring activity, AQLs and sampling plans may be applied to individual characteristics listed using an AQL of 0.65 percent for each Minor defect and an AQL of 0.40 percent for each Major defect, except where 100 percent inspection is specified. Equipment necessary for the performance of the insp

34、ections listed shall be in accordance with 4.2.4. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-(2-14747 (MU) 4.2.2.1 Relay and detonator assembly (see dwg. 9230474 covering a detail of dwg. 9229964). Categories Defects Method of Code No. ins

35、pection Critical: None defined. Major: 100 percent inspection 101. Detonator or relay improperly assembled . Visual O1001 Major: AQL 0.40 percent 102. Contents loose Visual- Manual 01002 Minor: AQL 0.65 percent 201. Evidence of poor workmanship (see 3.5) Visual 01003 4.2.2.2 Fuze adapter loading ass

36、embly (see dwg. 9229971 covering a detail of dwg. 9229964). Categories Defects Method of Code No. Inspection I Critical: None defined. Major : 100 percent inspection 101. Relay and detonator assembly missing . Visual 02001 Minor: AQL 0.65 percent 201. Distance from shoulder to base af detonator hous

37、ing, maximum, (max.) . Gage 02002 4.2.2.3 Projectile and fuze adapter assembly prior to assembling (see dwg. 9229964). Categories Defects Method of Code No. Inspection Critical: None defined. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Major :

38、100 percent inspection 101. Detonator improperly 102. Adhesive on detonator face. Visual 103. Adhesive on fuze adapter thread inadequate (prior to assembled Visual 03001 03002 assembling) (see 3.5.4) . Visual 03003 Minor: None defined. 4.2.2.4 Ejection charge loading assembly (see dwg. 9230008 cover

39、ing a detail of dwg. 9229964). Categories Defects Method of Code No. Critical: None defined. Major: AQL 0.40 percent Inspection I 101. Propellant weight incorrect Scale 04001 102. Bag torn or open in heat seal Visual- Manual 04002 Minor: AQL 0.65 percent 201. Evidence of poor . workmanship (see 3.5)

40、 Visual 04003 4.2.2.5 Projectile after installation of ejection charge loading assembly (see dwg. 9229964). Categories Defects Method of Code No. Inspection Critical: None defined. Major: 100 percent inspection 101. Ejection charge loading assembly missing or improperly positioned . Visual Major: AQ

41、L 0.40 percent 102. Any component including Minor: AQL 0.65 percent protective paper missing Visual 201. Evidence of poor workmanship (see 3.5) . Visual 05001 05002 05003 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14747 13 999970b 04b470

42、b U MIL-C-14747 (MU) 4.2.2.6 Categories Defects Method of Code No. Critical: None defined. Projectile prior to assembling plus and disc assembly (see dwg, 9229964) Inspection Major: AQL 0.40 percent Minor : None defined. 4.2.2.7 Projectile loading assembly (see dwg. 9229964). Categories Defects Meth

43、od of Code No. Critical: None defined, 101. Tracer missing or inverted. Visual 06001 Inspection Major: 100 percent inspection threads inadequate (prior to assembling) (see 3.5.4) . Visual 07001 101. Adhesive on rear body - Minor: AQL 1.0 percent 201. Marking missing, misleading 202. Evidence of poor

44、 . 07002 or unidentifiable Visual workmanship (see 3.5) Visual 07003 . 4.2.2.8 Loaded primer prior to assembling to cartridge case (see dwg. 8847424 covering a detail of dwg. 9229962). Categories Code No. Defects Method of Inspection Critical : 1. One or more flash holes . missing Visual 08001 Najor

45、: None defined. Minor: None defined. 4.2.2.9 (see dwg. 9229962) Cartridge case prior to insertion of projectile Categories Code No. Defects Method of inspection 8 Critical: None defined. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Major: AQL 0.40

46、 percent Minor: None defined. 4.2.2.10 Cartridge (see dwg. 9229962) . Categories Defects Method of Critical: None defined. 101. Foil disc missing Visual Inspection Major: Major: 101 . 102 . 103 . Minor: 201. 202. 203 . 4.2.2.11 100 percent inspection Primer above flush Gage AQL 0.40 percent Distance

47、 from case lip to rotating band Gage Primer not staked . Visual AQL 1.5 percent Marking missing, misleading or unidentifiable . Visual Projectile protective coating with total damaged area in excess of 1/4 Evidence of poor square inch . Visual workmanship (see 3.5) . Visual O9001 Code No. 10001 1000

48、2 10003 10004 10005 10006 Unsealed fiber container (see dwg. 9204453). Categories Defects Method of Code No. Inspection Critical: None defined. Major: AQL 0.40 percent 101. Any packing component missing or improperly assembled . Visual 11001 I Minor: AQL 1.5 percent 201. Cartridge cannot be removed

49、202. Container cap cannot be by hand . Manual 11002 removed by hand . Manual 11003 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-LLl747 13 0b OLlhLl708 1 MIL-C-14747 (MU) 203. Glue or asphalt on cartridge Visual 11004 4.2.2.12 Sealed fiber container before placing in barrier bag (see dwg. 920