ARMY MIL-C-43419 E-1989 CAP GARRISON MEN'S POLYESTER WOOL ARMY GREEN 344《军绿344男式毛涤纶船形帽》.pdf

1、- a- - ,. . IINCH-POUND( i2 April 19W SUPERSEDING MIL-C-43419D(GL) 26 September 1984 MILITARY SPECIFICATION CAP, GARRISON, MENS POLYESTER/WOOL, ARMY GREEN 344 This specification is approved for use by the U.S. Army Natick Research, Development and Engineering Center, Department of the Army, and is a

2、vailable for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a garrison cap made of polyester-wool blend material for male personnel. 1.2 Classification. The cap shall be of the following.types, classes and sizes as specified (see 6.2):

3、 Type 1 - Polyester-Wool, Tropical, Army Green 344 Class 1 - General Officerd Class 2 - Officers Class 3 - Warrant Officers Class 4 - Enlisted Personnel Type II - Polyester and Wool, Serge, Army Green 344 Class 1 - General Officers Class 2 - Officers Class 3 - Warrant Officers Class 4 - Enlisted Per

4、sonnel Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Research, Development and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Imp

5、rovement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS J Y ra ZU ma mc oc Q, u d C U U 2 - 6 X O Ln O In O O In In O O O Ln Ln Ln Ln O z I O 7 z 2

6、I 3 I I O T r z F P O M - O M Y O O m M rl . P W L O ld u3 a 2 8 o c O a cc rl ti- do- 4.ua c a, n, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-434L7E 4 777770b 0373632 O c 2 O In O IIn O O0 t- Ln b O In O0 InIn O O0 b Inn N -03 tI 03m zs 4

7、4 43 LI I 23 ? A Co Co. Fi O v- -F O M - a ci o L U . v1 a, o a, .ri a a, a .ri rn a c cd 9 E! g *ri rl c (d k a, d P v) v) 4 8 h E! 5 o a 5G x C a, s a,.dd cicici a o IA*rl E! o roo En0 o aua E! (du a, m o ox a, Dom ccio oarla cc a,(d(d(d 5 4 ac v) v) 04 Fi cia, aga v) c *d cd .Q k 5 o cci O a, bo

8、a a, a O ci c -0 ci ci KI ci .ri ci v). % E a O a, 6i c o P o oz . b c H 3 r X W o Lu o O a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. (It w O U p zu mn. mo O0 Pd W -I W W z - ta ! a O0 O O0 o lrlb m imb b O0 O O00 o mm lrl Lnmm b 4 zz II O0 -

9、7 2 I W www -FF L O O0 MIr F O M SIL O0 m m - o(d O00 orl -Ma- mo n a u c O o L W ; o 4 .d (d L (d x a .ri - P (d o O u C .ri (d u L 5 o a 2 G .d (d u L I o h O m a G C .d O e a 82 bo ha oa, Fi u O u C .d ld u L 2 h O u u O P i% $ ?3 0 L O o 6 Y c w * c u O L Y O c: o w m O OI Provided by IHSNot for

10、 ResaleNo reproduction or networking permitted without license from IHS-,-,-a 3 c U i 8 z MIL-C-Ll34L7E BLl H 7777706 0373b34 4 H MIL -C- 4 3 4 1 9 E( GL ) 2 I 03 nnn PPP vvv I Q) m cri .- I U P Co vl CIL O0 PPP P M,“ a- O M FP o LI0 M os r E1 U c O o c u P lu O O U c .rl (d U O a 5 fa .I c *ri (d U

11、 L a 6i O vi a 8 .ri O 9 6 coa 2 o a c (d P U (d a, 5 vi 4 z e U M c a, ri a .rl a, ci O U a c (d 9 U (d a, 5 vi 3 u ei 3 (d ea, a 0.a .ri PN(d L O . co . cn Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-:* n a e c O o L U 5 e (d P e (d a z 4 (d G

12、a s O e a G (d P e 8 G .r! O 5 SU cro O ro OU (d n 5 a, s c a, C 5 W 3-8 z c e (d P e (d 0 o .ri k P a, e (d a, U d 4 I 15 d W c * W K Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-43417E 4 W 7779706 0373636 W 2 I O F I t I I O M a- O n a I

13、o c v e a d i O .0 5 P I (d a, 3 vi C *d O ?I a d ld P 0 da,3, cued VI ei a 05 c c(d a ldP dPI a,I (d lda, 5a,5 a,5a ldeic rl 0.0 L a, ce IO a,LL c oc I a.O 3w 8 Ya, g.2 Y *d *oc, P.0 vi . c-. 5 a, 2 t: a, c 3 U L5 OE: (d P .0 (d a, 3 VI o .d k P (d ei a, .0 (d c L a, .0 rl 4 a .rl C d u 8 ma, via d

14、vi .d vi c, vid rl hm O a, vi3 50 s (do (d a, . . ? Cu r v- t. c 3 u B * h c u O c IL O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.8 Finished mea

15、surements. The finished measurements shall conform to table III. TABLE III. Finished measurements -II_ Overall curtain height at center Overall cap height Head size I/ at center 2/ (excluding braid) c 2/ - Cap size - - - Inches Inches Inches 6-3/) Sample size (number of sample units) 800. or less 2

16、801 to 22,000 inclusive 3 22,QOl and over 5 The lot The lot size and sample size shall be in accordance The basis for lot size and sample units for. testing shall; be as follows: Componenk Lot. size units Sample unit fur testing Interlining, CQ;OII Yards warp, horsehair filling 1 yard fulI width Pri

17、nt; cloth OF she.ek ing Yards t yard strip TABLE IV. Component and material testa Requirement Component Characteristic paragraph Test method Interlining, cotton warp, horsehair filling Weight per square yard 3.2.7.2 504 1 Yarns per inch 3.2.7.2 5050 Stiff ness (inch-pounds) 3.2.7.2 5202 Colorfastnes

18、s (when Visual 1/ Yarn ply, warp 3.2.7.2 - dyed yarn is used) to: Perspiration 3.2.7.2 5680 Wet-drycleaning 3.2.7.2 5622 Print cloth or Material identification 3.2.8 2/ Manual I/ sheeting, coated Wid th 3.2.8 - I/ One determination shall be made from each sample unit and the results - reported as li

19、passf or llfailll. All failures shall be described. - 2/ Unless otherwise specified, a certificate of compliance is required and will be acceptable for the requirement stated. 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c 4.4.2 In-process insp

20、ection. For the types I and II, classes 1 and 2 caps, in-process inspection shall be performed to assure that the stitching required on the curtain in table II, operation 7.b does not go through the cord edge of the braid. After the completion of operation 7.b, 15 percent of each hours production of

21、 the curtain from each stitching machine shall be randomly selected and inspected. The finding of any stitching in the cord edge shall be cause for rejection of that hours production. 4.4.3 Point count inspection. Sampling and inspection provisions for end item visual examination, dimensional examin

22、ation, and packaging examination shall be performed in accordance with MIL-STD-901. 4.4.4 Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be

23、 one palletized unit load, fully packaged. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. Examine Defect Finished dimension Length, width, or height exceeds specified maximum requirement. Palletization Weight Marking Pallet pattern not a

24、s specified. Interlocking of loads not as specified. Load not bonded with required straps as specified. Exceeds maximum load limits. Omitted; incorrect; illegible; of improper size, location, sequence, or method of application. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commerci

25、al as specified (see 6.2). 5.1.1 Level A. 5.1.1.1 Unit packing. Each cap shall be inserted into a snug-fitting flat style clear polyethylene film bag conforming to A-A-50083. 5.1.1.2 Intermediate packing. Forty caps of one size and class only, unit packed as specified in 5.1.1.1, shall be packed alt

26、ernatively (crown edge up and crown edge down) on edge in an intermediate fiberboard box conforming to style RSC, type CF, variety SW, class domestic, grade 175 of PPP-B-636. Inside dimensions of each box shall be 15 inches in length, 12-1/2 inches in width, and 5-1/2 inches in depth. Closure of box

27、es shall be effected with 2 inch minimum width gummed paper tape conforming to type III of PPP-T-45. 21 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5.1.2 Commercial. Caps shall be preserved in accordance with ASTM D 3951. 5.2 Packing. Packing sha

28、ll be level A, B or Commercial as specified (see 6.2). 5.2.1 Level A packing. Two hundred and forty caps of one size and class only, preserved as specified in 5.1, shall be packed in a fiberboard shipping container conforming to style RSC, grade V2s of PPP-B-636. intermediate boxes shall be packed f

29、lat two in length, one in width, and three in depth within a shipping container. container shall approximate 26-1/4 inches in length, 16 inches in width, and 18 inches in depth. Approximate dimensions are furnished as a guide only. Each shipping container shall be closed in accordance with method II

30、I, waterproofed in accordance with method V, and reinforced as specified in the appendix of PPP-B-636 except that the inspection shall be in accordance with MIL-STD-901. accordance with MIL-L-35078 for the type and class of load specified (see 6.2). II, class F loads. Level A Inside dimensions of ea

31、ch shipping Shipping containers shall be arranged in unit loads in Strapping shall be limited to nonmetallic strapping, except for type 5.2.2 Level B packing. Two hundred and forty caps of one size and class only, preserved as specified in 5.1, shall be packed in a fiberboard shipping container conf

32、orming to style RSC, type CF (variety SW) or SF, class domestic, grade 275 of PPP-B-636. Level A intermediate boxes shall be packed flat two in length, one in width, and three in depth within a shipping container. Inside dimensions of each shipping container shall approximate 26-1/4 inches in length

33、, 16 inches in width, and 18 inches in depth. Approximate dimensions are furnished as a guide only. Each shipping container shall be closed with method II as specified in the appendix of PPP-B-636 except that the inspection shall be in accordance with MIL-STD-901. 5.2.2.1 Weather-resistant fiberboar

34、d containers. When specified (see 6.2), the shipping container shall be a grade VC, VS, or V4s fiberboard box fabricated in accordance with PPP-B-636 and closed in accordance with method III as specified in the appendix of PPP-B-636 except that the inspection shall be in accordance with MIL-STD-901.

35、 5.2.3 Commercia3 packing. Caps, preserved as specified in 5.1, shall be packed in accordance with ASTM D 3951. 5.3 Palletization. When specified (see 6.2), caps, packed as specified in 5.2.2 and 5.2.3 shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD-147. Pallet

36、 type shall be type I (4-way entry), type IV, or type V in accordance with MIL-STD-147. from wood groups I, II, III, or IV of MIL-STD-731. Each prepared load shall be bonded with primary and secondary straps in accordance with bonding means K and L or film bonding means O or P. accordance with the a

37、ppendix of MIL-STD-147. effected by reversing the pattern of each course. Pallets shall be fabricated Pallet pattern shall be number 3 in Interlocking of loads shall be t 22 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-a. b. C. d. e. f. Q* h. i. M

38、IL-C-434 19E (GL) 5.4 Marking. In addition to any special marking required by the contract or purchase order, interior packs, shipping containers, and palletized unit loads shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. 5.4.1 Polyethylene bagged unit packs. Polyethylen

39、e bagged unit packs shall have the required identification information legibly printed or stamped in black directly on the bag across the center face or on a white paper label . inserted within the bag so as to permit ready identification. Each type I and type II, class 1, 2 and 3 cap shall be unit

40、packed with a caution instruction sheet inserted within the polyethylene bag (see 3.2.5.1). 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory. 6.1 Intended use. personnel of the Department of the Army. The caps are intended for w

41、ear by male Military 6.2 Ordering data. Acquisition documents should specify the following: Title, number, and date of this document. Type, class, and size required (see 1.2). Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see

42、 2.1.1 and 2.2). When a first article sample is required (see 3.1.2, 4.3, and 6.3). Class of braid required (see 3.2.3). Levels of preservation and packing (see 5.1 and 5.2). Type and class of unit load required (see 5.2.1). When weather-resistant grade fiberboard shipping containers are required fo

43、r level B packing (see 5.2.2.1). When palletization is required (see 5.3). 6.3 First article. When a first article is required, it shall be inspected and approved under the appropriate provisions of FAR 52.209, The first article should be a preproduction sample. specify the appropriate type of first

44、 article and the number of units to be furnished. The contracting officer should include specific instructions in acquisition documents regarding arrangements for selection, inspection, and approval of the first article. The contracting officer should 6.4 Sample. For access to samples, address the c

45、ontracting activity issuing the invitation for bids. 23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-43419E(GL) 6.5 Subject term (key word) listing. Headgear 6.6 Changes from previous issue. Marginal notations are not used in this revision t

46、o identify changes with respect to the previous issue due to the extensiveness of the changes. Custodian: Preparing activity: Army - GL Army - GL Review activities: (Project 8405-A0801 Army - MD DLA - CT 24 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-25 hS. GOVERNMENT PRINTING OFFICE: 198) - 634033Il2693 , ,=- - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-