ARMY MIL-C-43800 A-1983 COVERS PROTECTIVE AIRDROP HARDWARE AND EQUIPMENT GENERAL SPECIFICATION FOR《空投装备防护罩的通用规范》.pdf

1、 or tight tension resulting in tightness or puckering of material at stitch line Thread ends not trimmed Any row of stitching missing Needle chews Runoffs not restitched Any open seams Hardwar e NOTE: A seam will be classified as open when one or more stitches joining a seam are broken or two or mor

2、e consec- utive skippped stitches occur. Repairs of open seams shall not be scored as defects. Omitted, damaged, malformed, burred, or Not assembled as specified sharp edged Fasteners (hook Missing or misaligned and pile) Construct ion and workmanship Marking Any component missing, misaligned, or no

3、t joined as specified Grease, oil, dirt or other foreign matter in or on surface of cloth Raw edges not stitched as specified Webbing. not waxed as specif ied Webbing edges not seared as specified Not specified size or color Missing, incorrect, illegible, or improperly located X X X X X X X X X x X

4、X X X X X * 4.4.4 End item dimensional examination. The end item shall be examined for conformance to dimensions specified in applicable drawings. Any dimension not within the specified tolerance shall be classified as a defect. be expressed in units of one end item. inspection level shall be S-3 an

5、d the AQL, expressed in terms of defects per hundred units, shall be 6.5. The lot size shall The sample unit shall be one end item. The 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- J MIL-C-43OOA Lb W 7977706 OL7bf3 4 W 5 MIL-C-4 3800A c 4.4.5 P

6、ackaging inspection. An examination shall be made to determine that the preservation, packing, and marking comply with section 5 requirements. Defects shall be scored in accordance with table II. The sample unit shall be one shipping container fully packaged, except that it need not be closed. Exami

7、nation for closure defects listed in table 11 shall be made on shipping containers fully packaged. The lot size shall be the number of containers in the inspection lot. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 6.5. TABLE II. Packaging d

8、efects Examine Defect Materials Workmans hip Contents Component missing, damaged, defective, or not as specified Inadequate application of components such as improper closure of flaps Number per interior package or interior container not as specified Marking (interior Omitted, incorrect, illegible,

9、or improper size and exterior container) 5. PACKAGING 5.1 Preservation, packing, and marking. Preservation, packing, and marking shall be in accordance with the applicable Packaging Data Sheet (see 6.2). 6. NOTES 6.1 Intended use. The covers are intended to protect airdrop hardware and cargo from da

10、mage. 6.2 Ordering data. Acquisition documents should specify the following: a. Title, number, and date of this document. b. Cover required and stock number. C. When a first article is required (see 3.1, 4.2 and 6.3). d. Packaging data sheet required (-see 5.1). e. Selection of applicable levels of

11、preservation and packing (see 5.1) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 MIL-C-33OOA Lb 779770b 017b137 b W ? MIL-C-4 380OA 6.3 First article. When a first article sample is required, it shall he inspected and approved under the appropr

12、iate provisions of DAR 7-104-55. contracting officer should include specific instructions in all acquisition documents regarding definition of the first article in accordance with the DAR, number of units and arrangements for inspection and approval. The * 6.4 Recycled material. Recycled material sh

13、ould be used when practical as long as it meets the requirements of the document (see 3.2). 6a5 Changes from previous issue. The margins of this document are marked with an This was done as a convenience only asterick to indicate where changes (additions, deletions, modifications, corrections) from

14、the previous issue were made. and the Government assumes no liability whatsoever for any inaccuracies in these dotations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the las

15、t previous issue. Custodians: Preparing activity: Army - GL Navy - AS Air Force - 11 Army - GL Project No. 1670-0501 Review activities: Amy - A? Air Force - 82, 99 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-C-43800A Ib M 777770b OL9bI40

16、2 M - * MIL-C-43800A r, 9 APPENDIX 10. SCOPE 10.1 This Appendix lists and identifies the applicable USAF and NLABS drawings, titles, and Federal Stock Numbers of specific covers to be fabricated in accordance with the applicable drawing and the provisions of this specification. 20 APPLICABLE DOCUMXN

17、TS 20.1 bids or request for proposal, form a part of this appendix to the extent specified herein. The following documents, of the issue in effect on date of invitation for USAF NLABS - DRAWINGS AND STOCK NUMBERS TITLE NSN - 50C7406 Cover, Clevis, Aerial Delivery Kit 1670-00-360-0328 50C 7 49 6 Cove

18、r, Link, Single Suspension or Extraction 1670-00-360-0329 51C6174 Cover, Cargo, Aerial Delivery Kit , Side 1670-00-360-0324 51C6175 Cover, Cargo, Aerial Delivery Kit, End 1670-00-360-0323 11-1-674 Cover, Automatic Ripcord Release 1670-00-109-4697 (Copies of documents required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer .) f7lJ.S. GOVERNMENT PRINTING OFFICE: 1983-705-040/5741 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-