ARMY MIL-C-44216 A-1989 CANTEEN WATER COLLAPSIBLE 5-QUART CAPACITY《5夸特容量可折叠水箱》.pdf

1、MIL-C-442LbA 4 m 977970b 04OLY2L 7 I INCH-POUND I MIL-C-44216A 30 June 1989 MIL-C-44216 ( GL) 29 January 1986 MILITARY SPECIFICATION CANTEEN, WATER, COLLAPSIBLE, 5-QUART CAPACITY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope.

2、This specification covers a collapsible water canteen having a 5-quart capacity. 2. APPLICABLE DOCUMENTS 2.1 Government documents. J; 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks forin a part of this document to the extent specified herein. U

3、nless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement: thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertine

4、nt data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by le

5、tter. AMSC NIA FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L_ _. MIL-C-442LbA 84 977970b 040L422 9 W MIL-C-44216A SPECIFICATI

6、ONS FEDERAL L-P-349 - Plastic Molding and Extrusion Material, Cellulose L-P-3 7 5 - Plastic Film, Flexible, Vinyl Chloride Ac et at e, Butyrate PPP-B-56 6 - Boxes, Folding, Paperboard PPP-B-636 - Boxes, Shipping, Fiberboard PPP-8-676 - Boxes, Set-up PPP-T-45 - Tape, Gummed, Paper, Reinforced and Pla

7、in, For Sealing and Securing MILITARY MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification for MIL-C-43006 - Cloth and Strip Laminated, Vinyl-Nylon, High Strength Flexible MIL-C-44217 - Cap, Water Canteen, 5-Quar

8、t, Collapsible MIL-C-44218 - Carrier, and Canteen/Collapsible, 5-Quart Capacity MIL-C-44219 - Carrier, Canteen, Collapsible, 5-Quart Capacity STANDARDS FEDEAL FED-STD-66 - Steel: Chemical Composition and Hardenability FED-STD-191 - Textile Test Methods MILI TARY MIL-STD-105 - Sampling Procedures and

9、 Tables for Inspection by At tributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-130 - Identification Marking of U.S. Military Property NIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and

10、military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and public

11、ations form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. 2 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44216A DRAWINGS U.S. ARMY NATICK RESEARCH, DEVEL

12、OPMENT, AND ENGINEERNG CENTER 8-2-134 - Canteen, Water, Collapsible, 5-Quart Capacity (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014.) U.S. DEPARTMENT OF HEALTH AND HUMAN SERVICES Federal Food, Drug, and Cosmetic Act a

13、nd regulations promulgated thereunder (21 CFR, Parts 177 and 182) (The Code of Federal Regulations (CFR) and the Federal Register (FR) are for sale on a subscription basis by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. When indicated, reprints of certain r

14、egulations may be obtained from the Federal agency responsible for issuance thereof. ) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed

15、in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL SANITATION FOUNDATION (NSF) Standard No. 60 - Drinking Water Treatment Chemicals - Health E

16、ffects Standard No. 61 - Drinking Water System Components - Health Effects Listing of Food Service Equipment (Application for copies should be addressed to the National Sanitation Foundation, 3475 Plymouth Road, P.O. Box 1468, Ann Arbor, MI 48106.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D

17、 882 - Tensile Properties of Thin Plastic Sheeting D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Haterials, 1916 Race Street, Philadelphia, PA 19103.) (Non-Government standards and other publications are normal

18、ly available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44216A * 2.3 Order o

19、f precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS * 3.1 F

20、irst article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 6.31, in accordance with 4.3. 3.2 Samples. Samples, when furnished, are solely for guidance and information to the contractor (see 6.6). Variations from this specification may appear in the sample, i

21、n which case this specification shall govern. * 3.3 Material. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. * . 3.3.1 Purity. * 3.3.1.1 Resins. The resins used in the manufacture of the canteen neck, and the antioxidants or

22、 other substances incorporated in the plastic shall conform to 21 CFR, Part.177 (except Sections 177.1020, 177.1030, 177.1040, 177.1050 and 177.1480) and/or Part 182 to include testing in accordance with 177.2600 (e). * 3.3.1.2 Materials. The materials which are used to manufacture the canteen and w

23、hich may come in contact with the drinking water, shall comply with NSF Standard Numbers 60 and 61. 3.3.2 Vinyl film. The vinyl film used to fabricate the body of the canteen shall be unsupported vinyl film conforming to type I, class 1, 0.012 inches thick of L-P-375, except that the film thickness

24、shall be 0.014 + 0.0014 inch, and the film shall meet the purity requirements specified in 3.371. 3.3.3 Reinforcement neck. The neck reinforcement shall be molded from a vinyl chloride formulation as specified in 3.3.2, dimensions shall be in accordance with Drawing 8-2-134. 3.3.4 Neck (inner and ou

25、ter). The inner and outer neck shall be black and molded from a virgin cellulose acetate butyrate conforming to grade MS of L-P-349 which is combined with a suitable odor masking ingredient to substantially reduce the inherent odor, and which meets the purity requirements specified in 3.3.1. produce

26、d by molding. The surface shall have a uniformly high luster throughout : 3.3.5 Cap assembly. The cap assembly shall conform to MIL-(2-44217. 3.3.6 Strainer. The strainer filter shall be made of either 302 or 304 corrosion resisting steel conforming to FED-STD-66. minimum or 14 mesh maximum. The scr

27、een shall be 16 mesh Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-442LbA BLI 7777906 OYOL425 4 C . MIL-C-44216A 3.3.7 Reinforcement neck attachment. The neck attachment reinforcement shall be white and conform to type II, class 1, form 1 of

28、MIL-C-43006. 3.4 Design and construction. The collapsible water canteen shall conform to the design, shape, and dimensions shown on Drawing 8-2-134. * 3.4.1 Body. The canteen body shall be fabricated of material specified in 3.3.2 and heat sealed (flat seam) using a 1/8 inch wide heat seal. The neck

29、 with corresponding parts and reinforcements shall be suitably fastened to the body of the canteen as shown on Drawing 8-2-134 and shall meet all other requirements as specified herein. trudes after asseinbly, it shall be trimmed. Cement shall be used to bond the neck reinforcement to the outer neck

30、 in order to prevent the parts from turning or being removed,after assembly. contacting surfaces, i.e., there shall be no overflowing or smearing of cement on the end, inner, or outer surfaces of the neck assembly. The cap shall be attached and assembled to the outer neck as shown on Drawing 8-2-134

31、. All thread sections of the outer neck shall be smooth, clean, and free from nicks and damage. If an excess of the neck reinforcement pro- The cement shall be contained within the 3.4.2 Strainer. The strainer shall be constructed so that it may be inserted into the neck and removed manually with ea

32、se. Lt shall not be loose enough to fall out when the canteen, with the cap removed, is in the drinking position. 3.5 Performance. 3.5.1 Porosity. The canteen shall not leak air when tested as specified in 4.4.4. 3.5.2 Heat seal. The strength of the heat seal bond shall be not less than 65 percent o

33、f the breaking strength of the film when tested as specified in 4.4.4. * 3.5.3 Impact test. The canteen, when assembled in accordance with MIL-C- 44218, into a carrier conforming to MIL-C-44219 (see 6.4), shall not leak or fracture when subjected to the impact test as specified in 4.4.4. 3.5.4 Neck

34、bonding. The force necessary to remove the outer neck reinforce- ment shall be greater than 60.0 pounds when tested as specified in 4.4.4 (see 6.5). 3.6 Marking for identification. Marking shall be in accordance with MIL-STD-130 and the following: The letters “U.S.“ and contract data indicated below

35、 shall be printed ia black ink on each canteen and located as shown on Drawing 8-2-134. Canteen, Water, Collapsible, 5-Quart Capacity Stock Number Contractor Contract Number 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-The above contract data sh

36、all be block printed in 1/4 inch letters on the side opposite the “U. S .I. * 3.7 Workmanship. The Canteen shall conform to the quality of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS * 4.1 Responsibility for inspection. Unless otherwise specified in the contract or pur

37、chase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the insp

38、ection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. J: 4.1.1 Res

39、ponsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in this specification shall not reliev

40、e the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, howe

41、ver, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. J: 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is respo

42、nsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. * 4.1.3 Certificates of complian

43、ce. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: I a. First article inspection (see 4.3

44、) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44216A 84 9977906 OVO1427 8 t b e I MIL-C-44216A * 4.3 First article inspection. When a first article is required (see 3.1 and 6.21, it shall be examined for the defects specified in 4.4.3 and

45、 tested as specified in 4.4.4. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-CTD-105, 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with al

46、l the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. * 4.4.1.1. Component and material certification. The contractor shall furnish a certificate of compliance to the requirements of 3.3-1, 3.3.2,

47、3.3.4, 3.3.6 and 3.3.7. In addition, the odor and color of the neck material and the color of the neck reinforcement attachment shall be examined organoleptically as necessry to determine conformance to the odor and color requirements of 3.3.4 and 3.3.7. Any nonconformance to a purity or identity re

48、quirement shall be cause for rejection of the material or of any involved product. . * 4.4.1.2 Cap assembly examination. The contractor shall furnish a certificate of dompliance of this item to the requirements of MIL-C-44217. Any nonconformance to these requirements shall be cause for rejection of

49、this item or of any involved product. * 4.4.2 in-process inspection. Inspection of sub-assemblies shall be made to ascertain that construction details which cannot be examined in the finished product are in accordance with specified requirements. The Government reserves the right to exclude from consideration for acceptance, any material or service for which in-process inspection has indicated nonconformance. 4.4.2.1 Component dimensional examinati