ARMY MIL-C-48044-1972 CARTRIDGE 40MM PROOF XM387E4 LOADING ASSEMBLING AND PACKING《XM387E4型40MM防御炮弹的装卸 组装和包装》.pdf

1、i MIL-C-4 8 044 (MU) 28 January 1972 SUPERSEDING (See 6.11) MILITARY SPECIFICATION CARTRIDGE, 40MM, PROOF, XM387E4 LOADING, ASSEMBLING AND PACKING 1. SCOPE 1.1 This specification covers the loading, assembling and packing for one type of cartridge designated as Cartridge, 40MM, Proof, XM387E4. 2. AP

2、PLCABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation gor bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL PPP-T-7 6 - Tape, Pressure-Sensitive Adhesive, Paper, Water - Resistant PPP-T-9 7 - Ta

3、pe, Pressure-Sensitive Adhesive, Filament Rein- forced TT-1-559 c Ink, Marking Stencil, Opaque, for porous surfaces (wood, boxes, fiber carton, etc.) PPP-B-63 6 c Boxes, Fiber - -r- _. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-C-480q4 13

4、= 7777906 0315618 1 = MIL-C-4 8 044 (MU) MILITARY MIL-B-117 - MIL-A-2550 - MIL-1-45607 - STANDARDS MILTARY MIL-STD-105 - MIL-STD-109 - MIL-STD-1168 - MIL-STD-1169 - MIL-STD-1235 - DRAWINGS U.S. ARMY MUNITIONS 8844597 - PUBLCATIONS ARMY ET-8844597 - Bags, Interior Packaging Ammunition and Special Wea

5、pons, General Specification for Inspection Equipment, Acquisition, Maintenance and Disposition of Sampling Procedures and Tables for Inspection by Attributes (ABC-STD-105) Quality Assurance Terms and Definitions Lot Numbering of Ammunition Packaging, Packing and Marking for Shipment of Inert Ammuni-

6、 tion Components Single and Multilevel Continu- ous Sampling Procedures and Tables for Inspection by COMMAND Cartridge, 40MM, Proof, XM387E4 Equipment Tabulation 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-C-4 8 044 (MU) (Copies of specif

7、ications, standards, drawings and publications re- quired by suppliers in connection with specific procurement func- tions should be obtained from the procuring activity or as directed by the Contracting Officer). Other publications.-The following documents form a part of this specification to the e

8、xtent specified herein. wise indicated, the issue in effect on the date of invitation for bids or request for proposal shall apply. 2.2 Unless other- CODE OF FEDERAL REGULATIONS Title 49 c Transportation, Parts 0-190 (The Code of Federal Regulations is available from the Superintendent of Documents,

9、 U.S. Government Printing Office, Washington, D.C. 20402. Orders should specify, “49 CFR 0-190 (latest revision)“.) 3. REQUIREMENTS 3.1 Material.-Materials shall be in accordance with the applicable drawings and specificztions. ments specified on Drawing (Dwg) 8844597 and with all requirements speci

10、fied in applicable specifications. 3.2 Cartridge.-The cartridge shall comply with all require- 3.3 Primer functioning.-The primers shall function without evidence of squibbing or hangfire when tested as specified in 4.4.6. Paragraph 6.6 of MIL-P-20444B. Amendment 3 contains definitions of functionin

11、g failures. 3.4 Functioning.-The cartridge shall function satisfactorily and the projectile shall have a mean velocity of 247 plus or minus (4-1 7 feet-per-second (f.p.s.1 and a standard deviation not exceed- ing 4.5 f.p.s. when tested as specified in 4.4.5. Workmanship.-Fll parts and assemblies sha

12、ll be fabricated, loaded and assembled in a thorough, workmanlike manner. They shall be free of burrs, sharp edges, cracks, dirt, grease, rust, and other foreign matter. The cleaning method used shall not be injurious to any part, nor shall the parts be contaminated by the cleaning agents. Exterior

13、surface coatings shall be continuous except for a few light scratches not exposing base material. stamping shall be neat and sharply defined. 3.5 All required marking and 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4 8 044 (MU) 3.6 Submis

14、sion of results of contractor-conducted examinations and tests.-The contractor shall forward copies of the results of any of his examinations or tests to the designated address as required by the contract. (see 6.6). 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection.-Unless otherwise

15、 specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspectio

16、n requirements specified herein, unless disapproved by the Government. the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Reference shall be made to MIL-STD-109 to

17、define terms used herein. The provisions of MIL-A-2550 shall apply. The Government reserves 4.1.1 Submission of product.-At the the the completed lot of items deliverable under the contract is submitted to the Government for acceptance, the contractor shall supply the following information accomplis

18、hed by a certificate which attests that the information provided is correct and applicable to the product being submitted: a. A statement that the lot complies with all the quality assurance provisions specified in this specification. b. Drawing and specification number and date, together with ident

19、ification and date of changes thereto. c. A statement that all material purchased by the contractor meets requirements, when such material is controlled by Government or commercial specifications referenced in any of the contractual documents, and that certificates of conformance are on file and ava

20、ilable for review. d. Number of items in the lot. e. Date submitted. The certificate shall be signed by a responsible agent of the certifying organization. be substantiated by evidence of the agents authority to bind his principal. be required with subsequent certificates unless, during the course o

21、f the contract, this authority is vested in another agent of the certifying organization. The initial certificate submitted shall Substantiation of the agents authority will not 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-4 8 044 (MU) i

22、4.2 First article inspection.-Not applicable. 4 . 3 Inspection provisions. 4.3.1 Lot formation.-The term “inspection lot“ as used in this specification is defined as an essentially homogeneous collection of units of product from which a representative sample is drawn and inspected to determine confo

23、rmance with applicable requirements. The sample selected shall represent only that quantity of units from which the sample was drawn and shall not be construed to represent any prior or subsequent quantities presented for inspection. Homogeneity shall be considered to exist provided the inspection l

24、ot has been produced by one manufacturer, in one unchanged process, in accordance with the same drawing, same drawing revision, same specification and same specification revision and complies with the provisions for submission of product as specified in MIL-STD-105. Changes to process, specification

25、, or drawing not affecting safety, performance, mterchangeability, or storage, as determined by the Government, shall not be deemed to alter the homogeneity of an inspection lot. All material submitted for inspection in accordance with this specification shall comply with the homogeneity criteria sp

26、ecified herein regardless of the type of sampling procedure which is being applied to determine conformance with requirements. Lot numbering, as required, shall be in accordance with MIL-STD-1168. Each inspection lot shall contain: a. Cartridge case metal parts of one interfix lot number from b. Bod

27、y assemblies of one interfix lot number from one manu- C. Fuzes from one interfix lot number from one manufacturer. d. Primers from one lot number from one manufacturer. e. Propellant from one lot number from one manufacturer. 4.3.2 Examination.-The examinations listed in the following one manufactu

28、rer. facturer . subparagraphs shall be performed on inspection lots (See 4.3.1) of the components or assemblies designated in the applicable paragraph headings. Inspection for Critical defects (and Major defects, when so specified) shall be 100 percent. Sampling plans for Major and Minor defects sha

29、ll be in accordance with MIL-STD- 105 except that continuous sampling plans in accordance with MIL- STD-1235 may be used if approved by the Government. Instead of applying the AQLis designated herein to the groups of Major and 5 Provided by IHSNot for ResaleNo reproduction or networking permitted wi

30、thout license from IHS-,-,-MIL-C-LI044 13 7777706 0315622 3 MIL-C-4 8 04 4 (MU) Minor defects listed, the contractor may elect to apply AQLs to individual defects, using an AQL of 0.40 percent for each Major defect and an AQL of 0.65 percent for each Minor defect. When this method is elected, it sha

31、ll be applied to all of the Major and Minor defects listed in the applicable subparagraph of this section, except where 100 percent inspection is specified, and be documented as part of the contractors inspection system. Equipment necessary for the performance of the inspections listed shall be in a

32、ccordance with 4.3.4. 4.3.2.1 Cartridge case loading assembly, prior to inserting base plug and primer (See Dwg. 8844609 covering a detail of Dwg 8844597). Categories Defects Method of Code Inspection No. (See 6.2) Critical 1. Powder charge cup missing Gage o1 o o1 case Visual 01002 viously incorrec

33、t (See Para. 6.9) Visual O1 O 03 2. Spilled powder from cartridge 3. Propellant charge weight ob- Major 100% Lnspection 101. Propellant charge weight obviously incorrect (See para. 6.9) Visual O1 O 04 Minor: None defined 4.3.2.2 Cartridge case loading assembly, (See Dwg. 8844609 covering a detail of

34、 Dwg. 88445971. Categories Defects Method of Code Inspection No. Critical 1. Primer above flush with respect to base of case Gage 02001 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-LIOLILI 33 777990b 0335623 5 W Major: 101 . 102 . 103. 104

35、 . 105. Minor : 201, 202. AQL 1.00 Percent Base plug above flush Depth to base plug, maximum (max 1 Primer above flush or more than .O05 below with respect to base plug Incorrect primer Excessive varnish on eyterior surface of primer Marking misleading or unident- if iable Evidence of poor workmansh

36、ip (See 3.5) AQL 1.00 Percent MIL-C-4 8 04 4 (MU) Gage 02002 Gage 02003 Gage 02004 Visual 02005 Visual 02006 Visual Visual 02007 02008 4.3.2.3 Projectile (See Dwg. 8844596 covering a detail of dwq. 8844597). Categories Defects Critical: None defined Method of Code Inspection No. Major: AQL 0.40 Perc

37、ent 101. Weight incorrect Balance 03001 102. Plastic ogive assembled improperly (when applicable) Visual 03002 Minor : AQL 0.65 Percent 201. Evidence of poor workmanship (See 3.51 Visual 03 O 03 4.3.2.4 Cartridge, 40MM, Proof, XM387E4 (See Dwg. 8844597) Categories Defects Critical : None defined Maj

38、or: None defined Minor : AQL 1.50 Percent 201, Total length Method of Code Inspection No. Gage 04 001 7 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4 8 04 4 (MU) 202. Marking misleading or 203. Evidence of poor workmanship unidentifiable

39、Visual 04002 (See 3.5) Visual 04 003 4.3.2.5 Unsealed fiber box (See Section 5). Categories Defects Critical: None defined Method of Code Inspection No. Major: AQL O. 65 Percent 101. Cartridge facing wrong way Visual 05001 102. Improper number of cartridges Visual 05002 103, Separator missing Visual

40、 05 O 03 Minor: None defined 4.3.2.6 Sealed fiber box, prior to sealing bag (See Section 5). Categories Defects Critical: None de.fined Method of Code Inspection No. Major : AQL 0.40 Percent 101. Container damaged Visual 06001 102. Corners not blunted Visual 06002 Minor: AQL O. 65 Percent 201. Conte

41、nts loose Manual 06003 202. Label missing or unidentifiable Visual 06004 4.3.2.7 Unsealed outer packing box (See Section 5). Categories Defects Critical: None defined Method of Code Inspection No. Major: AQL 0.65.Percent 101, Inner fiber box facing wrong wall Visual 07 001 8 Provided by IHSNot for R

42、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4 8 04 4 (MU) 102. Marking of bag misleading or unidentifiable Visual 103. Bag torn or perforated Visual 104. Bag improperly sealed Visual Minor: None defined 4.3.2.8 Sealed outer packing box (See Section 5). Categories

43、Defects Critical: None defined Method of Inspection Major : AQL 0.40 Percent 101. Box damaged Visual 102. Strapping missing or improperly assembled Visual Minor: AQL 1.50 Percent 201. Contents loose Manual 202. Car seal missing or improperly positioned Visual 203. Marking misleading or unidentifiabl

44、e Visual 4.33 Testing. 4.3.3.1 Check test for deterioration of primers (See Specification MIL-P-20444) Major Defect.-if the total time between original acceptance of any lot and the assembly of 07002 07003 07 004 Code No. 08001 08002 08 O 03 08 004 08005 that lot into the cartridge exceeas two years

45、 or if the primers have been subjected to adverse conditions, however brief, at any time since previous tests, the primer lot shall be subjected to and must satisfactorily pass, the check test for deterioration specified in MIL-P-20444 immediately before the primer lot is assembled into the cartridg

46、e. This test shall be performed by the contractor on primers selected by the Government Inspector at the facility assembling the primer into the cartridge (See 6.4). cost to the contractor who loaded the primer or the contractor assembling the primer into the cartridge, and shall not constitute a ba

47、sis for rejection against either contractor except where deterioration has occurred as a direct result of carelessness in handling, storage, etc., permitted while the primer lot was under the responsibility of either contractor. The test shall be conducted at Government expense without 9 - -. Provid

48、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-4 8 O4 4 (MU) The Contracting Officer shall arrange to have the con- tractor reimbursed for expenses incurred in the performance of check tests. 4.3.3.2 Propellant weight of cartridge case, Code No. 090

49、01.- The propellant weight shall be determined and then check-weiqhed - 100 percent. ently of the original weighing or determination, using a different balance from that used to make the original weighing, and if performed manually shall be performed by another operator. Any charge which fails to comply with the requirement specified on Dwg. 8844609, shall be classified defective and remo