ARMY MIL-C-50697-1971 CORD DETONATING《导火线》.pdf

1、E. MIL-C-50b77 13 777770b 0q2b730 2 TT-1-559 MIL-C-50697 17 February 1971 MILITARY SPECIFICATION . CORD, DETONATING “This specification is mandatory for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification establishes the performance, design and acceptanc

2、e requirements for metal sheathed detonating cord used to transfer explosive energy in ballistic energy transfer systems, 1.2 Classification. Detonating cord (DC) shall be of the types and classes as specified in Section 3. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect o

3、n date of invitation for bids or request for proposal, form a part of this speci- fication to the extent specified herein: SPEC1 FICAT IONS Federal Ink, Marking Stencil, Opaque for Porous. Surfaces (wood boxes fiber cartons). WW-T-775 Tube, Copper, Seamless (For Refrigera- tion and General Use) MMM-

4、A-178 Adhesive, Paper Label, Water-resistant PPP-B-636 Box, fiberboard PPP-B-6 76 Box, Setup Military MIL-P-3 8 7 MIL-R-39 8 Psntaerythrite Tetranitrate (PEXN) FSC 1377 , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50697 MIL-B-242 7 MIL-A-2

5、550 d MIL-S-13282 MIL-R-21723 Department of the Navy WS 4660 ,WS 5003D STANDARDS Military PICL-STD- 10 5 MIL-S TD- 109 MIL-STD-810 MIL-S TD- 116 8 MIL-STD- 12 35 PUBLICATIONS . DOD 4145.26M Box, Anununition Packing, Wood, Nailed .Ammunition and Special Weapons; General Specification for Silver and S

6、ilver Alloy RDX Composition CH 6 DIPAM HNS Explosive Sampling Procedures and Table or Inspection by Attributes Quality Assurance Terms and Definitions Environmental Test Methods Lot Numbering of Ammunition Single and Multilevel Continuous Sampling Procedures and Tables for Inspection by Attribute DO

7、D Contractors Safety Manual for Anununition, Explosives and Related Dangerous Material (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contrac

8、ting officer.) 2.2 Other Publications. The following documents form a part of this specification.$o. the extent specified herein. issue in effect on date of invitation for bids or request for proposal shall Unless otherwise indicated the apply Code of Federal Regulations CFR 171-178 Department of Tr

9、ansportation Rules and Regulations for the Transportation of Explosives and other Dangerous Articles by Land and Water. Society of Automotive Engineers AMs-7721 Lead Alloy Sheet and Extrusions 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-5

10、0697 13 M 977990b 0426732 b M MIL-C-50697 NO. 1 2 3 - (Applications for copies should be addressed to the Society of Automotive Engineers, Inc., 485 Lexington Ave., New York, N. Y. 10017.) 3. REQUIREIENTS 3.1 Material. The detonating cord siiall consist of an explosive encased in a metal sheath. The

11、 material used in the manufacture of the detonating cord shall designate the type and class; i.e., the type by the core explosive and the class by the metal sheath material. 3.1.1 Type I (PETN). The PLTN used in the manufacture of the detonating cord shall comply with MIL-P-387. (Not for naval aircr

12、aft application) 3.1.2 Type II (RDX). The RDX (cyclotrimethylenetrinitramine) used in the manufacture of detonating cord shall comply with MIL-R-398, Type II Class C. (Not for naval aircraft application) 3.1.3 Type III (DIPAM). The DIPAM (dipicramide) used in the manufacture of detonating cord shall

13、 comply with WS 4660. 3.1.4 Type IV (BNS). The UNS (hexamitrostilbene) used in the manufacture of detonating cord shall comply with WS-5003D. 3.1.5 Type V (CB6). shall comply with MIL-R-21723. The CH6 used in the manufacture of detonating cord 3.1.6 Class A (Copper). The copper used in the manufactu

14、re of detonating cord shall comply with WW-T-775, 3.1.7 Class U (Silver). The silver used in the manufacture of detonating cord shall comply with MIL-S-13282. 3.1.8 Class C (Lead). The lead used in the manufacture of detonating cord shall comply with AMs 7721. 3.1.9 Class D (Aluminum), The aluminum

15、used in the manufacture of detonating cord shall be free of impurities and have a minimum content of 99.78i pure aluminum. 3.2 Dimension. Unless otherwise specified, dimensions shall be in accordance with Table I and shall apply after all manufacturing, process treatments and nondestructive testing

16、have been completed. There shall be no deviation from applicable drawing configuration, dimensions and tolerances. TABLE I Core Load Outer Dia for Metal grains/f oot Sheath + .010” 2.5 3 4 ,073 .O80 .O92 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

17、,-,-MIL-C-50b77 13 m 77777Ob 042b733 W MIL-C-50697 TABLE I continued 4 5 6 7 8 9 10 11 12 .5 061 7 .072 10 .086 15 105 20 .122 25 30 136 150 40 .175 50 -195 3.3 Radiographic examination. The detonating cord shall be X-rayed to as- certain there are no voids, inclusions or impurities in the explosive

18、 core or metal sheath. 3.4 Flexibility. The detonating cord shall be capable of being bent on a radius as specified in Table 2, without any visual signs of cracking of the metal sheath or degradation of performance. TABLE 2 FLEXIBILITY REQUIREMENTS Explosive Loading - No. (grains/foot 4 5 5 7 6 10 7

19、 8 15 20 9 25 10 30 11 40 Bend Radius (inches) 0.50 0.75 1.00 1.50 2.00 2.50 3.00 4.00 50 5.00 12 3.5 Splicing. There shall be no splices. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-50697 13 W 9999906 042673q T W MIL- C- 50 6 9 7 3.6 Im

20、pact Resistance. The detonating cord while mounted on a steel plate shall not detonate or deflagrate when impacted with a twenty pound steel ball dropped. from a height of 30 inches. 3.7 Detonation Velocity. The minimum detonation velocity of the DC shall be as listed in Table 3. TABLE 3 DETONATION

21、VELOCITY Explosive Core finimum Detonation Velocity PETN 8200 meters/sec 8100 meters/sec RIX DIPAM . 7000 meters/sec HNS .6800 meters/sec CH6 6800 meters/sec 3.8 Detonation Continuity. The detonating cord shall uniformally propagate along its complete length when tested in accordance with 4.5.6. 3.9

22、 Core Loading (grains per foot) and Sheath Diameter. In addition to type and class, the detonating cord shall be assigned a numerical character, to designate the core loading and sheath diameter. Table I lists the numerical designation and the associated. core loading and sheath diameter. 3.10 High

23、Temperature. The detonating cord shall be capable of with- standing the high temperature as specified in Table 4 without degradation of perf ormance. 6xp lo s ive PETN RDX. Cii6 DIPAM TABLE 4 HIGH TEMPERATURE Temperature 150F 250F 250F 350F HNS 350F 3.11 Low Temperature. a low temperature of -65F wi

24、thout degradation of performance. The detonating cord shall be capable of withstanding 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* f MIL- C-506 9 7 3.12 Workmanship. Workmanship shall be of the highest grade throughout and in accordance with

25、the best standard practice. 4. QUALITY ASSURhCE PROVISIONS 4.1 General, Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection re- quirements as specified, the supplier may utilize his own facilities or any commercial laborator

26、y acceptable to the Government, The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements . Reference shall be made to MIL-STb109 in order to define

27、 the terms used herein. The provisions of MIL-A-2550 shall apply 9 4,l.l Submission of Product. At tne time completed lot of product is submitted to the Gavernment for acceptance the contractor shall supply the following information accompanied by a certificate which attests that the information pro

28、vided is correct and applicable to the product being submitted: (a) (b) (c) (d) (e) A statement that the lot complies with all quality assurance provisions specified in this specification. Number of units or product inspected. Results obtained for all inspections performed, Drawing, specification nu

29、mber and date, together with an identifica- Certificates of conformance on all material purchased by the con- tion and date of changes. tractor when such material is controlled by government or commercial specifi- cations referenced in any of the contractual documents. (f) Number of items in the lot

30、. (g) Date submitted. The certificate shall be signed by a responsible agent of the certifying organi- zation. of the agents authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certificates unless, during the course of the contract, this autho

31、rity is vested in another agent of the certifying organization. The initial certificate submitted shall be substantiated by evidence 4.1.2 Government Verification. Using the contractors written quality assurance procedure, this detail specification, the applicable drawings and other contractual docu

32、ments as a guide, the government inspector shall verify at unscheduled Intervals all quality assurance operations performed by the contractor. Verification will be performed to the extent necessary to assure compliance with the contractual requirements. Severity of government inspec- tion of indlvid

33、ual characteristics will be directly related to the seriousness of the classification assigned. 4.1.3 Preproduction Inspection. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50697 13 W 9999906 0426736 3 = M L- C- 506 9 7 4.1.3.1 Submission.

34、 Prior to the start of regular production, the contractor shall submit a preproduction sample to a government approved facility as designated by .the Contracting Officer (see 6.3) for evaluation in accordance with the provisions of 4.1.3.2. The preproduction sample shall consist of five spools which

35、 have been produced by the contractor or furnished by a supplier and which have been manufactured using the same pro- duction processes, procedures and equipment which will be used in fulfilling the contract. All materials, including packaging and packing, shall be ob- tained from the same sources o

36、f supply as will be used in regular production. The sample shall be accompanied by certificates of conformance for materials. A preproduction sample, or portion thereof, as directed by the contracting officer, shall also be submitted whenever a change occurs in manufacturing process, material used o

37、r source of supply such as to significantly affect product uniformity as determined by the government. Prior to submission, the contractor shall inspect the sample to the degree necessary to assure that it conforms to the requirements of the contract and submit a record of this in- . spection with t

38、he sample. A sample containing known defects will riot be sub- mitted unless specifically authorized by the contracting officer. 4.1.3.2 Inspections to be Performed. The spools will be subjected by the government to any or all of the exaniiiations specified in this specifica- tion and any or all req

39、uirements of the applicable drawing. 4.1.3.3 Rejection. If any sample fails to comply with any or all of the applicable requirements, the initial production sample shall be rejected, The government reserves the right to terminate its inspection upon any failure of any component in the sample to comp

40、ly with any of the stated re- quirements. In the event of rejection, the government reserves the right to require the contractor to take corrective action and submit a new initial production sample or portion thereof. Until an initial production sample is accepted, the contractor is in no way author

41、ized by the government to initiate regular production unless otherwise directed by the Contracting Officer. 4.2 Inspection Provisions. 4.2.1 Lot Formation. A lot size shall not exceed that quantity of detonating cord produced in one continuing process using one lot of explosive and one lot of sheath

42、ing material. The sample selected shall represent only that quantity of units from which the sample was drawn and shall not be con- strued to represent any prior or subsequent quantities presented for inspec- tion. produced by one manufacturer, in one unchanged process, in accordance with the same d

43、rawfig,. specification, or revision thereof, Changes to either the process, specification or drawing not affecting safety, performance, inter- changeability or storage, as determined by the government inspector, shall not be deemed to alter the homogeneity of the lot. comply with MIL-STD-105 and sha

44、ll be numbered in accordance with MIL-STD-1168. Unless otherwise approved by the Contracting Officer, the inspection lot size of major assemblies or end items deliverable under the contract shall be not less than the smallest weekly estimate of quantities contractually scheduled for production durin

45、g the contract period nor more than the largest quantity contractually scheduled for delivery during any month of the contract period. Homogeneity shall be considered to exist provided the lot has been Inspection lots shall 7 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

46、ut license from IHS-,-,-MIL- C- 5069 7 4.2.2 Examination. Inspection for critical defects (and major defects, when so specified) shall be 100 percent. Sampling plans and procedures for major and minor defects shall be in .accordance with ML-STD-105 except that continuous sampling plans in accordance

47、 with MIL-STD-1235 may be used if approved by the procuring activity. 4.2.3 Testinq. 4.2.3.1 General. The contractor shall make available to the government all inspection equipment necessary for determining conformance with contract requirements. Personnel for operating the equipment and verificatio

48、n of its accuracy, shall be supplied by the contractor for the performance of examina- tion or test by the government. 4.2.3.2 Sampling. Visual Inspection. Unless otherwise specified visual inspection shall be performed on all samples. 4.2.3.3 Testing. Unless otherwise specified acceptance tests sha

49、ll be performed on 110 feet of the production lot of detonating cord. Test samples shall be chosen at random in as much as possible and cut to the size required for individual tes t. 4.2.3.4 X-Ray Examination. The detonating cord shall be X-Rayed to ascertain there are no voids, inclusions or impurities in the explosive core or metal sheath. 4.3 Classifications of Test The inspection and testing of the DC shall be classified as f