ARMY MIL-C-51475-1980 CARRIER ASSEMBLY《载体组装》.pdf

1、MIL-C-51475(EA) 16 June 1980 (See section 6) MILITARY SPECIFICATION CARRIER ASSEMBLY This specification 9s approved for use by US Army Armament Research and Development Command, Department of the Army and is available for use by all Depart- ments and Agencies of the Department of Defense. 1. SCOPE 1

2、.1 Scope. - This specification.covers one type of carrier assembly. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in ef- fect on date of invitation for bids or request for proposal, forma pt of this specification to the extent speclfied herein: STANDARDS FEDER

3、AL FED-STD-123 - Marking for Shipment (Civil Agencies). . MILITARY MIL-STD-105 MIL-STD-1168 - Lot Numbering of Ammunition. - Sampling Procedures and Tables for Inspection by Attributes. DRAWING AND TECHNICAL DATA PACKAGE LIST (TDPL) US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND CHEMICAL SYSTEMS

4、LABORATORY TDPL.122-3-143 - Carrier Assembly. FSC 1040 : Beneficial comments (recommendations, additions, deletions) and any : pertinent data which may be of use in improving thisdocument should be : : addressed to: Commander, US Army Armament Research and Development : : Command, ATTN: : : ing the

5、selt-addressed Standardization Document Improvement Proposal : : (DD Fomn 1426) appearing at the end of this document or by letter. DRDAR-TSC-S, Aberdeen hving Ground, MD 21010 by us- THIS DOCUMENT CONTAINS 6 PAGES. - 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

6、ense from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-51q75 10 I 7797906 0334232 i m 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. 4.1.1 Contractors responsibility. Unless otherwise specified in the contract, th

7、e contractor is responsible for the performance of all inspec- tion requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own OP any other facilities suit- able for the performance o%? the inspection requirements specified herein, unless disappro

8、ved by the Government. The Government reserves the right. to perform any of the inspections set forth in the specification where such inspections are deemed necessary to.assure supplies and services conform to prescribed requirements. 4.1.2 Objective evidence. The contractor shall provide objective

9、evidence acceptable to the contracting officer that the requirements of 3.1 and section 5 for which specific inspectiop has not been pro- vided in this specification have been satisfied. 4.2 Classification of inspections. - - (a) Preproduction inspection (4.3). (b ) Quality conformance inspect ion (

10、 4.4 ; 4.3 Preproduction inspection. 4.3.1 Lot. A preproduction lot of 109 each components for carrier. - assemblies shall be manufactured using the same methods, materials, equipment and ppocesses as will be used during regulm production. 4.3.2 Inspection procedure. 4.3.2.1 For examination. A sampl

11、e of 1 each components subassemblies and assemblies shall be examined 100 percent to all drawing dimensions. 4.3.2.2 Acceptance/rej ection criteria The preproduction sample shall comply with the examinations specified in 4.3.2 to be acceptable. acceptance number is zero. Bom the contracting officer

12、prior to proceeding with regular production. The The conWactor shall obtah wltten approval 4.4 Quality conformance inspection. 4.4.1 Lotting. Each lot shall be identified and controlled in ac- cordance with MIL-STD-1168. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without

13、license from IHS-,-,-MIL-CL5147 5 (EA) 4.4.2 Sampling. Sampling shall be conducted in accordance with MIL-STD-105. 4.4.3 Inspect ion procedure. MIL-STD-105. (a) Case inseparable assembly (Drawing D122-3-59). Critical : None defined Major: AQL 1.0 percent defective Component missing Component incorre

14、ctly assembled (b) Ejector, projectile (Drawing C122-3-41). Major: AQL 1.5 percent defective Projectile interface OD incomect Location of flange incorrect Fbofiie of flange incorrect Diameter of flange incorrect Internal tapers incorrect External tapers incorrect (c) Holder, projectile (Drawing C122

15、-3-42). Critical : None defined Major: AQL 1.5 percent defective ID of projectile interface incorrect OD of bead incorrect Slots incorrect or incorrectly located ID of ejector interface incorrect , Li. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Custodian : Army - EA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-