ARMY MIL-D-60095-1964 DETONATOR ELECTRIC XM65 LOADING ASSEMBLING& PACKING《XM65型电能激发雷管的装载 组装及包装》.pdf

1、MIL-D-60075 23 W 7797906 0335508 6 = r- - - /- MIL-D- 60095 (MU) 30 October 1964 MILITARY SPECIFICATION DhTONATOR, ELECTFtIC, XM65 LOAPINO, ASSEMBLING AND PACKING 1. SCOPE 1.1 This specification contains requirements not normally required by Lhe drawings and p-ovides for quality asurance provisions

2、for the loading, assembling and packing for one type of fnitiating device designated 8s Detonator, Electric, xbI65, 2. APPLICABLE DO-NTS. 2.1 The following documents of the Issue in effect on date of invitation for bids or request for proposals, form a part of this epeciflcatlon to the extent specif

3、ied herein. SPECIFICATIONS MILITARY MIL-P-116 - Preservatfon, Methods of. MIL-A-2550 - Ammunition md Special Weapons; General Specification for. MIL-P-14077 -.Polytgtafluoroethylene (Teflon), Molding aid Extruding Material. ML-1-45208 - Inspection Requfrements, General Specification for, MIL-1-45607

4、 - fnspection Equipment, Supply and BYalnteneutce of. STANDARDS MILITARY ML-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (ABC-STD-105). I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-I)-60095 (Mu) ML-STD-109 MiL-STD-

5、1235 - Single and Multilevel Continuous - Quality AssuranCe Terms and Definitions. Samplng Procedures and Tables for Inspection by Attributes, DRAWINGS ORDNANCE CORPS 8798134 - Ammunition Container, Hetal Por Detonators 8798135 - Box, Packlng, Ammuntton for Detonators 8798136 - Box, Set-up, Packing,

6、 Amunition for Detonators 9204230 - Detonator, Electric XM65 Assembly. Electric. Electric. Electric. PUBLICATIONS ORDNANCE CORPS IEL-9204230 - Index of Inspection Equipment Lists. (Copes of speclficationa, standards, drawings and publications required by contractors in connection with specific procu

7、rement functions should be obtained from the procuring activity or a8 directed by the contracting officer). 3. REQUIREMENTS 5.1 Material.-Matrials shall be in accordance wth applicable 3.2 Detonator.-The detonator shall comply with all requments dpawings and specfffcatlons. specified on ion by the G

8、overnment;, Any critical defect encountered, unless annotated by an asterrk (*) to the rlght of the chakacterlstic cade mmber (aste 6.2)s will be repopted wfttifai 48 hours. clpiticai defects amstated by an asterisk wili be fwnishad. The agencies tu whm tke repmts will be furrdahsd ape idcrn+iffed i

9、n paragrzf G,6, The reporta ahall. cotstal? as a inZnurn, Lhe following information; Reierence shall be made to The Contractrss quality assurance eystxm.-Ths contractor 4.3.1 A moz=arisy rhipmt c0vePir.g those a. ConPractor and con%at mmke b. C. Characteslwtlo code tluarher. . Lot or Berial number.

10、e. Number of defectives fouraol of the contractor OP the mope of the coritrai-t, the report. skiell. ontafn the cntrczchrce recommendation to the Government;. Number and revidioas ing for acceptance by the Goverment ehal be s%opped. Subsequen% testing for waterproofness, duds, and output. shall not

11、be conducted. The standmd deviation shall be calculated using ths fokmrrla lin 6.6 OP its equivalent. 4.%.9,4.2 Waterproofness (see 3.5) - Major defect Code No. 03015, outgut (see 3.6.2) - Major defect - Code No. 03016 and duds (see 3.6.3) - Ma,jur defect - Code No. 03014.4f the lot has not been PJe

12、ctssl in 4.%.3.4.0b9 a portion of SO detonators shall be tested a8 epeclficad in 4.3.5, using test equipment specified In 4.2.4. The lot shall be rejected if two OF more detonators fail to produce a perfoation in the disc of the required size. fal to fim shall he replaced with detonators from the Pe

13、maning goktioa of bhe ox+gfnal sample. encountered dwng the time and output tests combined, the 10% shall be kejected and fwther teaking for acceptance by the Government shall be stopped. If a total of three dude has not been encountered buk one detonator fafla 60 create a perforation in the lead di

14、sc of the required sizes the balance of the original sample ahall be tested ais $peeiffed in 4.3.4. The lot shall be rejected and testing for Goverment acceptance shall be stopped If and when one or mom detonator fail8 to weate a perforation in ehe disc of the pequlped size OF when a tP;al of thme d

15、uds is encountered in all the combned testing. Detonators that If a total of three duds has been 4.2.3.4.3 Thab (me 3.6.3) - Major defect - Code No. 03014.-ff all of the fipst 50 detonatore teated In 4.2.3.4.2 unction satis- facto?ify ia the outgut phase, and the lot has not been rejected for duds;

16、the xoemanng gok%ioa of the original sample shall be subjected to the teat for uda specified in 4.3.6. The lot shall be rejected when and if a total of three dud6 ia encountered in all of %he omb%ned tesixhg and testing for Government acceptance erhall be stopped. If two du. Lists shall be submitted

17、 for approval to the inspection elemenk of the agency administering the contract. 6.3.6 Contractor designs.-Contractor deslgns are designs of inspection equipment for which the Government has assigned design responsibility to the contractor. Contractor designs shall be supported by detailed drawings

18、 which depict all information necessary to completely fabricate, calibrate and operate an item of inspection equipment. This requires that the necessary views, dimensions, materialis, finish, notes, operating and calibration instructions be properly depleted in accordance wfth approved practices to

19、the extent that fwthsr calculation or clarification will not be required. Contractor designs fdentified as CDCF may be developed on the format the contractor normally employs in his equipment design procedure provided auch format reflects the detail and information specified above. contractor design

20、s identified as CDAF shall comply with the format and requirements of MIL-D-45608, and In addition, contain the detail and information specified above, 15 -. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-60075 13 7797706 0335523 2 MIL-D- 6009

21、5 (MU) . 6.3.7 Submission of contractor esigns.-Deslgns shall be submitted for approval to the Commanding Officer, Picatinny Arsenal, AIYITJ: SMPA-ND. Design review will normally be accomplished within one month after receipt by Picatinny Arsenal. Partial submission of inspection equipment esigns is

22、 permissible and encouraged. However, the Arsenal completion date for design review will be based on the date of the final submission of designs, 6.4 Submissfon of critical defect reports.-For U, Se Army Munitions Comman procurements9 one copy of each critical defect report will be furnished the cog

23、nizant Government inspection agency; the Army Ammunition Procurement and Supply Agency, Am: SMUAP-RO; Picatinny Arsenal, ATTN: SMPA-ND. 6.4.1 Reporting to other services.-For other than U. S, Army Munitions Command procurements, critical defect reporting shall be as prescribed by the Contracting Off

24、icer. be performed only when required by the specification covering subsequent use of this detonator In the next assembly or end iten, Two hundred (2330) detonators shall be selected for this test. 6.5.1 Fuaictisning tinit! and duds.-Forty (40) detonators shall be subjected to the test specified in

25、4.3.4. Observation shall be made for the functioning time and all duds that may occur shall be recorded. If the mean time (re) plus 2,03 times the standard deviation (8) exceed 10 micPosecondso the lot shall be rejected, The standard deviation shall be computed from the formula in 6.6 or its equival

26、ent. Duds shall not enter into the calculation for standard deviation. 6.5.2 Waterproofness, sutput, and duds, -Fifty (50) detonators shall be subjeets ta the test specified in 4,3.5. be made of the perforation Pn the disc, and the duds that may occur shall be recorded. 200 selected. lead disc, a re

27、test shall be permitted using the balance of the detonators selected in 6.5. If during the retest one more detonator fails to adequately perforate the lead disc, the retest shall be stopped and the lot rejected. During the retest the number of duds that may occm shall be recorded. If three or more d

28、etonators fail to adequately perforate the lead disc during the original test the lot shall be rejected without retest. 6.5. Check test fop possible deterioration.-This teat shall Du& will be replaced by detonators from the 200 selected. Observation shall Duds shal be replaced by detonators from the

29、 If two detonators fail to adequately perforate the 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-D-bO075 13 W 7777706 0335524 4 = MZ-I)- 60095 (MU) 6.5.3 Duds.-If no rstect is required in the output phase, the balance of the detonators sel

30、ected in 6.5 chal1 be subjected to the test for duds as specified in 4.3.E. ?Ire numbea, of duda that may-occur will be recorded, If more than two but not more than six duds are found a retest may be permitted ushe double the numbw of detonators selected in 6.5. The lot shall be rejected during Pete

31、st as soon as the total number of duds observed in 6.5.1, 6.5.2 and 6.5.3 1s equal to seven. If in the original sample of SOO, seven or more duds Fe-observed the lot shall be rejected without retest. formula or equivalent shall be used In calculating the sample standapd deviation: 6,6 Calculation of

32、 sample standard deviation.-The following s =pF- where : a = sample standard deviation. x 7 numerical value of individual observations. x = average value of the sample. n = gample size. 6.7 - Check test expense.-The contracting Officer should arrange to have the contractor reimbursed for any expense incurred in the performance of the check test for possible deterioration. Custodian: Army-plfiJ. Preparing activity: Army-Nu Project No. 1375A789 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-