ARMY MIL-D-63370-1981 DISPENSER MINE GROUND VEHICLE M128 PREPARATION FOR SHIPMENT& STORAGE OF《M128型矿山地面炸药车辆装运及贮藏准备》.pdf

1、1. MIL-D-b3370 13 7777906 0347043 3 5-3%3 MIL-D-63370(AR) 18 September 1981 MILITARY SPECIFICATION DISPENSER, MINE: GROUND VEHICLE, M128; PREPARATION FOR SHIPMENT AND STORAGE OF This specification is approved for use by the US Army Armament Research and Development-Command, and is available for use

2、by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification provides the general requirements for the preservation, packaging, packing and marking for the M128 Ground Vehicle Mine Dispenser and shall hereafter be referred to as processing. 1.2 Classification.

3、 Processing for shipment and storage shall be Level A in accordance with the provisions of this specification. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified

4、herein. SPECIFICATIONS FEDERAL L-P-378 GG-T-250 NN-P-530 QQ-5-781 S S -G- 65 9 -T-81 W-F-800 MMM-A- 1 78 MMM-A- 2 60 PPP-B-62 1 PPP-B-636 PPP-F-320 Plastic Sheet and Strip, Thin Gauge, Polyolefin Tester, Antifreeze Solutions Plywood, Flat, Panel Strapping, Steel, Flat and Seals Graphite, Dry (Lubric

5、ating) Tags, Shipping and Stock Fuel Oil, Diesel Adhesive, Paper Label, Water- Resistant Adhesive, Water-resistant (For Sealing Waterproof Paper 1 Box, Wood, Nailed and Lock-Corner Boxes, Shipping, Fiberboard Fiberboard; Corrugated and Solid, Sheet Stock (Container Grade) and Cut Shapes fi- . Provid

6、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Mn-D-63 370 (AR) PPP -T -7 6 PPP-T-60 PPP -T -9 7 PPP-T-42 PPP 4- 179 7 MILITARY MIL -P - 11 6 MIL-B- 117 MIL -B - 12 1 MIL-L-2105 MIL-C-5501 MIL-H-60 83 MIL-P - 8 7 93 MIL-C- 11 755 MIL-C-17504 MIL-L- 21 260

7、 MIL-B-2219.1 MIL-P- 2 65 14 MIL-P-46002 MIT.-A-461 53 MIL-B-46176 MIL-T-46755 MIL-E-52 798 MIL-P-603 12 MIL-E812 98 Fed. Test Method Std. Tape, Packing, Paper (For Carton Sealing) Tape, Packaging, Waterproof Tape; Pressure-Sensitive Adhesive, Filament Rei nf or c ed Tape, Packaging - Masking, Paper

8、 Cushioning Material, Low Density, Unicellular, Polypropylene Foam Preservation-Packaging, Methods of. Bags, Sleeves and Tubing Interior Packaging Barrier Material, Waterproofed, Greaseproof ed, Flexible Lubricating Oil, Gear, Mu1 tipurpose Caps and Plugs, Protective, Dust and Moisture Seal Hydrauli

9、c Fluid, Petroleum Base, for Preservation and Operation Paint (Gloss and Nonspecular), For Use On Elastomeric Pigmented Film Antifreeze, Artic-Type. Coating, Canpound, Acrylic Clear Lubricating Oil, Internal Combustion Engine, Preservative and Break-In Barrier Materials, Transparent, Flexible, Heat

10、S ea1 ab1 e Polyurethane Foam, Rigid or Flexible, For Packaging Preservative Oil, Contact and Volatile Corrosion Inhibited Antifreeze, Ethylene Glycol, Inhibited, Heavy Duty, Single Package Brake Fluid, Silicone, Automotive All Weather, Operational and Preservative Tires, Pneumatic and Tires, Semipn

11、eumatic: Installed on Vehicles, Preparation for Storage Enamel, Alkyd, Camouflage Parts, Molded, Plastic Foam, Polystyrene Dye, Liquid Red, for the Detection of Leaks in STANDARDS FEDERAL NO. 141 - ircGaft Fuei systems Paint, Varnish, Lacquer and Related Materials, Methods of Inspection, Sampling an

12、d Testing o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. _ _ MIL-D-63370 13 7797706 03q70L15 7 E MIL-D-63370 (AR) MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage D

13、RAWINGS U.S. ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND 9291399 - Dispenser Fitted Cover TECHNICAL MANUAL MILITARY TM-55-1095-205-14 - Transportability Guidance, Dispenser, Mine: Ground Vehicle, M128 (Copies of specifications, standards, drawings and publications required by suppliers in connect

14、ion with specified procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 Materials. Materials shall be in accordance with all applicable specifications and standards. the supplier and shall be subject to all provisions of

15、 this specification. Materials not specified shall be selected by 3.1.1 Tags. Tags used for identification and warning marking shall conform to UU-T-81, Type A with waterproof ink. 3.2 Initial Production Dispenser. Unless otherwise specified, one of the Approval of one of the first ten (10) producti

16、on processed first ten (10) production processed dispensers shall be subjected to the inspection in 4.2. dispensers shall not relieve the supplier of his obligation to process all dispensers in accordance with this specification. specified by the procuring activity, any change to materials or proces

17、sing after approval of one of the first ten (10) production processed dispenser shall require an additional production processed dispenser be inspected as specified in 4.2 inspected. Except as otherwise Government representative shall select the dispenser to be 3 Provided by IHSNot for ResaleNo repr

18、oduction or networking permitted without license from IHS-,-,-MIL-D-63370 (AR) 3.3 Processing. Level A. 3.3.1 Record Forms. Information on forms shall include preservation accomplished and depreservation instructions. The Equipment Log Book Binder and one (1) copy of DD Form 1397 shall be placed in

19、a bag conforming to Type I, Class B, Style 2 of MIL-B-117, 6 mil thick. Bag shall be closed by heat sealing and secured in the operators control box storage cabinet. The other copy of DD Form 1397 shall be waterproofed with adhesive conforming to MMM-A-178 and securely attached to the door of the el

20、ectrical enclosure. Two (2) copies of DI) Form 1397 shall be provided. 3.3.2 Repainting. Painted surfaces of the dispenser on which the paint has been damaged shall be cleaned and repainted in accordance with the painting requirements of the end item specification (see 6.3). 3.3.3 Preservatives and

21、Atomize Spray Equipment. Preservatives specified herein, identified by “P“ number, shall conform to the applicable e. specifications listed in MIL-P-116. oils is specified, equipment shown in Figures 1 and 2, or equivalent, shall be used. every 50 feet or fraction thereof. When atomize spraying of p

22、reservative Compressed air supply lines shall be equipped with moisture separators 3.3.4 Disassembly. Maximum reduction in cube shall be effected for shipment to ports and overseas, or to facilitate loading the maximum number of dispensers on the conmion carrier. The four (4) leveling jacks shall be

23、 raised to their highest adjustment and rotated to the stowed position. pin shall be engaged in each jack. The lower, retractable lunette shall be moved to the inner positon and secured with locking pin. reflectors shall be removed, (two (2) from front sides of dispenser and two (2) from rear sides)

24、, and screws, washers, lens and gasket secured to each reflector housing with tape, PPP-T-42. Reflectors shall be stored in the on vehicle equipment (OVE) storage box (see 3.3.5). The locking Four (4) side 3.3.5 On Vehicle Equipment (OVE). The on vehicle equipment (OVE) for the dispenser consists of

25、 a spade, fire extinguisher, mine dispenser manual crank, tire hand crank, four (4) leveling jack hand cranks, an inadvertent mine prevention pin assembly, two (2) safety chain shackles, and tool kit. Included in the tool kit is a tools roll, tire gauge, pliers, two (2) screwdrivers, double-end sock

26、et, three (3) wrenches, rawhide mallet and socket wrench bar. installed in the large round tube located in the OVE cabinet under the operators control box storage cabinet. with P-19 preservative and installed in the smaller round tube located in the OVE cabinet. coated with P-19 preservative and ind

27、ividually wrapped in barrier material, tools shall be packed into the tools roll, the roll folded tightly and installed on the top shelf inside the operators control box storage cabinet. The rawhide mallet shall be installed in the circular tube located on the side wall inside the operators control

28、box storage cabinet. The double-end socket shall be coated with P-19 preservative and The socket wrench bar shall be coated The tire gauge, pliers, screwdrivers, and wrenches shall be type II, grade A, class 2, MIL-B-121 and secured with tape, PPP-T-42. These . The spade, mine 4 Provided by IHSNot f

29、or ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-D-b3370 13 W 9999906 0349047 O W . t MIL-D-63 3 70 (AR) dispenser manual crank, tire hand crank and four (4) leveling jack hand cranks shall each be coated with P-19 preservative and stored in the wood OVE storage bo

30、x as shown in Figure 5. The fire extinguisher, inadvertent mine prevention pin assembly (wrap pennant around pin), two (2) safety chain shackles (coat with P-19 preservative) and four (4) reflectors (see 3.3.4) are each to be placed in fiberboard boxes, boxes sealed with tape, PPP-T-76 and stored in

31、 the wood OVE: storage box as shown in Figure 5. (Add additional filler material to each box to assure tight packing.) Two (2) belts (alternator and fan) removed from the engine (see 3.3.11) shall be placed in barrier bag, the barrier bag heat sealed and the belts stored in the wood OVE storage box

32、as shown in Figure 5. The keys for the padlocks (see 3.3.24) shall be placed in the barrier bag, the bag heat sealed and the keys stored in the wood OVE storage box as shown in Figure 5. Six (6) cushions shall be positioned around and on top of items as shown in Figure 5 to insure tight packing. sha

33、ll be added, as required, to insure contents are tightly packed. The wood box shall be closed by strapping with three (3) metal straps, class 1, type I, finish B, size 3/4 in, QQ-S-781. Each fiberboard box, bag and wood box shall be marked to indicate contents, in accordance with MIL-STD-129. Filler

34、 material 3.3.5.1 Wood OVE Storage Box On Dispenser. The packed and strapped wood OVE storage box (see 3.3.5 and Figure 5) shall be placed on the front of the dispenser-chassis, behind the control cable connector and in front of the launcher assembly. The box shall be positioned across the width of

35、the chassis and secured to the chassis with two (2) metal straps, class 1, type I, finish R, size 3/4 in, QQ-S-781. One strap shall be positioned across the forward portion of the box, down the ends and under the chassis. The second strap shall be positioned across the rear portion of the box, aroun

36、d and under the dispenser brake support and under the chassis. fiberboard, PPP-F-320, shall be placed at each contact point between the strapping and the chassis. A piece of solid 3.3.6 Printed Circuit Card Assembly For Built In Test Equipment (B.I.T.E.)/ALARM Control Panel. assemblies shall be remo

37、ved from the B.I.T.E./ALARM control panel and packaged The seventeen (17) printed circuit card separately for shipment on the dispenser. placed over the connector on each card assembly. wrapped with one polypropylene wrap and secured with three (3) pieces of tape, PPP-T-42. Card assembly 1 thru 16 s

38、hall be wrapped in the 12 x 10 in. cushioning and card assembly 17 shall be wrapped in the 16 x 7 1/2 in. cushioning. Each wrapped card assembly shall be inserted into a barrier bag and heat sealed. Wrapped card assembly 1 thru 16 shall be inserted into the 6 1/2 x 14 in. bag and card assembly 17 sh

39、all be inserted into the 8 1/2 x 11 1/2 in. bag. Each card assembly 2, 3, and 4 shall be placed into one of the 10 1/4 x 5 3/8 x 1 1/4 in. fiberboard box, card assembly 1, 5 thru 16 into a 10 1/4 x 5 3/8 x 1 in. fiberboard box and card assembly 17 into the 7 3/4 x 7 3/4 x 1 1/8 fiberboard box. Each

40、box and bag shall be marked indicating nomenclature of card assembly enclosed. A rubber shorting- bar shall- be . Each card assembly shall be . Each box shall be sealed with tape, PPP-T-76. Cushions and packed fiberboard boxes shall be placed in wood box as 5 Provided by IHSNot for ResaleNo reproduc

41、tion or networking permitted without license from IHS-,-,-. MIL-D-63370 13 4997906 03Y40YB 2 9 MIL-D-63 3 70 (AR) shown in Figure 6. Fiberboard boxes containing card assemblies 1 thru 14 shall be placed on their sides into the wood box on top of the bottom cushion. Fiberboard boxes containing card a

42、ssemblies 15, 16 and 17 shall be laid flat and placed on top of the other boxes and then the top cushion placed over these boxes . Filler material, PPP-F-320, shall be added around contents, as required, for tight packing. two (2) metal straps, class 1, type I, finish B, size 314 in, QQ-S-781. The e

43、xterior of wood box shall be marked indicating contents, in accordance with MIL-STD- 129 . Wood box shall be closed by strapping with 3.3.6.1 Wood Box With Printed Circuit Card Assembly On Dispenser. The packed and strapped wood box containing the printed circuit card assembly (see 3.3.6 and Figure

44、6) shall be placed on top of the operators control box storage cabinet. The box shall be secured in place with two (2) metal straps, class 1, type I, finish B, size 314 in, QQ-S-781, positioned widthwise and one metal strap lengthwise over the box and downjthe sides and ends and under the cabinet. c

45、ontact point between the strapping and the storage cabinet. A piece of solid fiberboard, PPP-F-320, shall be placed at each 3.3.7 Rubber Tires. For shipment by all modes of transportation except over the road, tires mounted on wheels (road tires) shall be inflated to 10 pounds launcher tire shall be

46、 inflated to noma1 operating pressure and preserved in accordance Wi th MIL-T-46755. above pressure recommended for a maximum load. Spare tire and 3.3.8 Cleaning and Drying. Exterior surfaces of the dispenser shall be free of dirt, dust, grease and any other contaminants. Exposed surfaces for which

47、application of a preservative is specified shall be cleaned and dried in accordance with any applicable process and procedure of MIL-P-116 which will accomplish cleaning and not damage the item. 3.3.9 Miscellaneous Preservation. All exterior, unpainted surfaces including all surface type finishes su

48、ch as black oxide chromates and phosphates shall be coated with type P-19 preservative. not limited to, safety chains, springs, both lunette assemblies, tube fittings, brackets, clamps, leveling jacks and drawbar surf aces exposed by disassembly. All exposed oil can points such as, but not limited t

49、o, levers, locking bars, latches, hinges, hinge pins, locking pins, lunette pins, locking levers, linkage and threaded ends of yokes and related clevis pins shall be lubricated with oil conforming to P-9 preservative. Working mechanisms of padlocks, latches, door locks and hand operated locking knobs shall be lubricated with graphite conforming to SS-G-659. Excess lubricant shall be removed after lubrication. This includes, but is 3.3.10 Cooling System. Cooling system