ARMY MIL-D-64021 A-1988 DISPENSER GROUND M131 M136 SYSTEM COMPONENT PARTS FOR《M131 M136型地面炸药系统的组成部分》.pdf

1、. 1 . _ - lIL-D-64021A 13 7997906 0353005 4 MIL-D-6402lA(AR) ,- 10 JUNE 1988 SUPERSEDING MIL-D-64021 (AR) 20 OCtober 1986 MILITARY SPECIFICATION DISPENSER, GROUND: M131/M136 SYSTEM COMPONENT PARTS FOR This specification is approved for use within the U.S. Army Armament, Munitions and Chemical Comman

2、d, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification contains requirements and Quality Assurance provisions for the MOPE Tube Kit and Dispenser Kit assemblies. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specific

3、ations and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless 0th rwise specified, the issues of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. Ben

4、eficial commenls (recommendations, additions, deletions) and any pertinent data which may be of use in Improving this document should be addressed to: Commander. U.S. Army Armament,Munitions and Chemical Command, Attn. AMSMC-QA. Picatinny Arsenal, New Jersey 07806-5000 by using the self-addressed St

5、andardize- tion Document Improvement Proposal (DD Form 1426) appearing it the end of this document or by letter. AMSMC NIA FSC 1345 DISTRIBUTION STATEMENT D. Distribution authorized to the Department of Defense and DoD Contractors only. This Technical Data Package contains sensitive technology on a

6、new weapons system. 1987. Other requests for this document will be referred to: Commander, ARDEC, ATTN: SMCAR-FSM, Picatinny Arsenal, NJ 07806-5000. DESTRUCTION NOTICE. For classified documents, follow procedures in DoD 5200, 22-M, Industrial Security Manual, Section 11-19 or DoD 5200, 1-R, Informat

7、ion Security Program Regulation, Chapter Ix. For classified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document. This determination was made on 10 July /THISDOCUMENT CONTAINS % PAGES. . Provided by IHSNot for ResaleNo reproduction or n

8、etworking permitted without license from IHS-,-,-NIL-D-64021A 13 99799Ob 0353006 b MIL-D-64021A(AR) SPECIFICATIONS FEDERAL QQ-P-4.16 - Plating, Cadmium (Electrodeposited) MILITARY MIL-C-5541 - Chemical Conversion Coatings on Aluminum and Aluminum Alloys. MIL-A-8625 - Anodic Coatings, For Aluminum an

9、d Aluminum Alloys. MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables or MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-1169 - Packaging, Packing and Marking for Inspection by Attributes

10、. Shipment of Inert Ammunition Components. 2.1.2 Other Government documents, drawinqs and publication. The following other Government documents form a part of this specification to the extent herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRA

11、WINGS U.S. ARMY ARMAMENTS RESEARCH, DEVELOPMEN,T AND ENGINEERING CENTER. (ARDEC ). 929xoa 9292800 9292801 9292802 9292804 9292805 9292806 9292807 9292808 9292810 9292811 9292812 9292813 9292814 92 92 817 9292818 9292819 9292820 929282L 9292822 - Tape, Pressure S,ensitive - Cover, Bottom - Base - Bra

12、cket - Module, Foamed - Strap - Plate, Nut - Base Assembly - Cable Assembly - Cover Assembly - Handle, Carrying - Bracket, Tie Down - Bracket, Handle - Pin, Quick Release - Disk, Initiation System - Detonating Cord As.sembly - Plugr Breech - Spacer, Breech - Disk, Pressure Seal 2 - CQVer, Tap Provid

13、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-publ. 9292823 9292830 9292832 9292834 9292835 9292837 9292828 9292839 9292840 9292841 9292842 92 92 844 9292856 9292858 9292859 9292862 9292863 9292865 9292867 9292868 9337501 9337502 9337503 9337508 9337509

14、9337510 12590261 - Lock Pin Assembly - Body, Out of Line Safety - Block, Detonator Assembly - Detonator Assembly, Electric - Detonator, Electric - Spring, Compression - Pin, Shear - Obturator - Spring - Conical - Spider - Ring, Shear - Double - Bar, Retainer - Tube Assembly - Breech - Holder, Actuat

15、or - Actuator Housing Assembly - Housing Assembly, Out of Line Safety - Shutter - Actuator, linear Pyrotechnic - Spacer, Forward - Spacer, Aft - Coil, Data Transfer - Pin, Borerider - Disc, Tape - Plate, Retainer Borerider - Test Dispenser 2opies of spec cations, standards, handbooks, hlrawings, zat

16、ions and other Government documents required by the contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity). 2.2 Other publications. The following document(s) form a part of this specification to the e

17、xtent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment d

18、ocuments which is current on the date of the so lic it at ion . AMERICAN SOCIETY FOR TESTING MATERIALS (ASTM) ASTM-B-117 - Method of Salt Spray (Fog) Testing ASTM-D-3951 - Pack-Commercial Packaging (Application for copies of ASTM publications should be addressed to the American Society for Testing a

19、nd Materials, 1916 Race Street, Philadelphia, Pennsylvania, 19103). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-64021A 13 m 7999906 0353008 T m t ( 2.3 Order of precedence. In the event of a conflict between he text of this specification

20、and the references cited herein except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtai

21、ned. 3. REQUIREMENTS 3.1 Material. Materials shall be in accordance with applicable drawings and specifications. 3.2 Components and assemblies. The components and assemblies shall comply with all requirements specified on drawings and specifications referenced therein. 3.3 Detonatinq cord assembly o

22、utput test. The detonator cord when taped to a 6061-0 aluminum witness plate .lo0 inch thick and initiated at ambient temperature by a detonator, shall provide a score, tactile with the fingernail, in the aluminum witness plate. 3.4 Electric detonator performance characteristics. 3.4.1 Detonator ass

23、embly resistance test. The detonator assembly shall have a resistance at the end of the leads of 1.15 + - .25 ohms while at ambient temperature. 3.4.2 No fire test. The electric detonator shall not fire when subjected to the electrical current of 1 ampere minimum for 5 minutes minimum while at 75F+1

24、00F. 3.4.3 All fire test. The electric detonator shall fire on the first attempt when subjected to the application of a DC current not to exceed 3 amperes in amplitude for a maximum period of 50 milliseconds while at that 75OF+1OoF. 3.4.4 Dent test. The minimum dent in a steel witness plate generate

25、d by the electric detonator placed directly against the center of the witness plate shall not be less than 9.5 mil, when fired at ambient temperature. The witness plate shall be 5/8 inch thick, cold finish steel No. C1018 or C1020 having a hardness of Rockwell B70 to B95. 3.4.5 Waterproofness test.

26、The electric detonator shall fire after being subjected to soaking for 48 hours in 75OF+5OF of water . 3.4.6 Cold temperature function. The electric detonator shall fire after being conditioned for 2 hours at -60F-50F. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

27、cense from IHS-,-,-NIL-D-69021A 13 m 7779706 0353009 1 m MIL-D-64021A(AR) 3.4.7 Hot temperature function. The electric detonator shall 3.5 3.5.1 Bridqe wire resistance. The bellows actuator shall X fire after being conditioned at 2 hours at S160F+50F. Linear pyrotechnic actuator performance characte

28、ristics. have a bridge wire resistance of .29 5 .O8 ohms while at 7 5051 O OF . 3.5.2 No fire test. The Linear Pyrotechnic actuator shall not fire when subjected to the electrical current of 1 ampere minimum for 5 minutes minimum while at 75O+1OoF. - 3.5.3 All fire test. The Linear Pyrotechnic actua

29、tor shall fire on the first attempt when subjected to the application of a DC current not to exceed 4.5 amperes in amplitude for a maximum period of 10 milleseconds while at 75+100F. 3.5.4 Output test. The Linear Pyrotechnic actuator shall produce a force of 15 inch pounds at 60 angle or 30 inch pou

30、nds at 15O angle when electrical current is applied. 3.5.5 Functioninq test. The Linear Pyrotechnic actuator shall function by extending for a stroke length of 0.50 inch minimum in 25.0 milliseconds maximum when electrical current is applied while at 75F+100F. 3.6 First article inspection. This spec

31、ification contains technical provisions for first article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the contract. 3.7 Workmanship. All parts and assemblies shall be fabricated and assembled in a thorough, workmanlike manner. They

32、shall be free of burrs, chips, sharp edges, cracks, surface defects, dirt, grease, rust, corrosion products and other foreign matter. The cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agent. All required markings shall be neat and sharply

33、 defined. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase o

34、rder, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Governmnet reserves the right to perform any of the inspections set forth in the specification where such inspections a

35、re deemed necessary to assure supplies and services conform to prescribed requirements. Unless otherwi ecf herein or in the contract, the provisions of MIL-A-z$O% skaffd apply and are hereby made a part 9 this detail specification. Provided by IHSNot for ResaleNo reproduction or networking permitted

36、 without license from IHS-,-,-MIL-D-64023A 33 7777706 0353030 W 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absen

37、ce of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submissi

38、on of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.2 Classification of inspections. The following types of inspection shall be conducted on this item: a. First article inspection b. Quality conformance inspection 4.3 F

39、irst article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the contracting officer for evaluation in accordance with provisions of 4.3.2 and 4.3.3. The first article sample shall consist of parts/assemblies and sample quantities listed in Table I.

40、1 specified herein. 4.3.2 Inspections to be performed. See MIL-A-48078 and Table 4.3.3 Rejection. See MIL-A-48078. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-D-6402LA 13 7797706 0353033 T m U 4 rl cv O e Io I B I E i r i! r Y ta VI d Y W n

41、 rn E pc 8 U rn 4J E a, E O ai u u a, rn E al Q 2 .FI n b cvm rll-lrlcvme am r-bbbbb -Pm mmmmmm we W-P-P-P-Ptr . cv tr cvm *;ru) ee m cv cv w -P . . m rlrl cvm-PmDIDb em ewe-PedC. mm mmmmmm . cvm NW cv mm mm m *. *. . I I I IIIIII II I 111111 II mmm mm mm O rlrlrl rlrlrl rlrl rlrl rl mmm o rn a, 4J

42、7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. O H 2 Q1 b cv E B rn O E 3 v m U c a, c O pi W Lt a, m C a, Q i? !g - MIL-D-bq021A 13 9999906 0353032 1 m m. cum zrm zrzr . Co cu cum zrm *di O * cum *m di* m cu cum zrm *-Y rl Nzr cul7 cucu cucu cu

43、cu mm mm mm mm mm a. II II II II II II II II II -II mm om om om om rlrl rl rl rl rl m c, u a, W a, a g ai G.2 33a on x u-w 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-tlIL-D-611021A 13 M 7777706 03530111 5 E !g i: a ai a, M QI 8 =J k n M c Pi 2

44、 v rn ci C a, C O pi u L-i a, rn c a, Q M ,rl n cv ni ni NN m m m mm nicv mm . . e* b. II. I I I II II I I I II O m O 0U-l d l-l rl rl om. rl rn c, u a, cw a, a rn rn. rn c, 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-F- a O u u a, rn C .ri a,

45、 rl u .rl u .rl 2 u rn u .rl Fri . H W I4 a ! - MIL-D-64023A 13 17777706 0353035 7 m 8 m E s n m z pi 2 v rn ci C a, C O pi u u a, rn C a, pi rn .rl n O cu cum crm *cr cucu Olm cu CJ CJCJ mm mm m m mm 0. . . II II I I II II II I I II om Om m O Oin rl rl rl rl rl rn ci u a, w a, a (II u u a, W a, a 1

46、1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e c O .rl U u a, rn c .rl a 4 u .rl U u ta U to u 4 cri c H El GI m ! QI 8 ti W P CI m O c 3 Y rn U c a, C O FL u u a, a, G z 2 4 n MIL-D-bg021A 13 W 777770b 0353016 7 I m ri mm CYm *-Y . N NN N nl N

47、m mm M m m . . - I II I I I I II I I I O om O O O rl d d rl l-i rn 4J u a, w a, ea 3- orl LI 0l-i 4.a c HN o QI -4 -N ci ciQI ta Q,c A rl u WE ta$ ucl x m-w rn U u a, a, 5 u -0 COW m ac uicv o id QI .4 a,NU CQIta mc c3id 4 fa x pi-w . G.2 12 P Provided by IHSNot for ResaleNo reproduction or networki

48、ng permitted without license from IHS-,-,-2 O .d c, u a, z .d a, rl u 4 CI u td ci u) u .FI Fri . H w 2 h - MIL-D-LY023A 33 79799b 0353037 O tn 8 P E, R h vi c pi O c v u) c, c a, c O a u u a, u) c !i !G - E x E E L Y w a I A =I C 7 n O 7 E L O LL a v 4 O I u I v, e n 26 Provided by IHSNot for Resal

49、eNo reproduction or networking permitted without license from IHS-,-,-a d a c P c c r c C U I . T 2 : I- r Y) w k d r Y 8 LL .m n Z O F: il z 3 u MIL-D-bLI021A 33 H 7797706 0353033 5 CV 8 CV !i 25 a al O Fr al rl 5 a -h 8 rl rl. rl NCVNNCVN b mmmmmm m *. 0 a a . . 3 3u c lk ci pc .I+ c o a r u O 3 2) O