ARMY MIL-DTL-11132 12 F-2013 INSIGNIA RANK CADET FIRST LIEUTENANT ROTC AND JROTC U S AIR FORCE.pdf

1、 AMSC N/A Page 1 of 3 FSC 8455 INCH - POUND MIL-DTL-11132/12F 4 March 2013 SUPERSEDING MIL-DTL-11132/12E 6 June 1997 DETAIL SPECIFICATION SHEET INSIGNIA, RANK, CADET, FIRST LIEUTENANT, ROTC AND JROTC, U.S. AIR FORCE This specification is approved for use by all Departments and Agencies of the Depart

2、ment of Defense The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-11132. DASH NO. -1: ROTC Regular Size -2: ROTC Miniature Size -3: JRTOC (see Note 2) MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230) FINISH: Epoxy res

3、in (Stoning epoxy), Nickel Plated, Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/12E Page 2 of 3 DIMENSIONS: HEIGHT (Overall): -1: 2-1/

4、4 inches (REF) -2, -3: 1-3/16 inches (REF) WIDTH (Overall) -1: 1-5/16 inches (REF) -2, -3: 11/16 inch (REF) THICKNESS (Overall): -1, -2: 0.070 inch + 0.010 inch -3: 0.100 inch + 0.010 inch (Including Plastic Back Plate) EPOXY: Epoxy resin shall be applied to the insignia rank as indicated above, and

5、 shall match TIOH Hard Enamel Color Chip Numbers listed below. Hard cloisonn enamel may be used in lieu of epoxy. If hard cloisonn enamel is used, the required base material shall be Gilding Metal 95/5 (UNS Alloy C-210). TIOH HARD ENAMEL COLOR CHIPS COLOR CHIP NUMBER Blue #18 ATTACHING DEVICE: The a

6、ttaching device shall be a prong clutch type as follows. 1. -1 shall have three prongs and clutches. One prong shall be located on the vertical center line 3/16 inch + 1/32 inch below the top of the insignia and one prong in each of the lower corners 3/16 inch + 1/32 inch in from the sides and up fr

7、om the bottom. 2. -2 and -3 shall have two prongs located on the vertical center line of the insignia, equidistant from each end and 3/4 inch + 1/32 inch apart. NOTES: 1. The term (REF) refers to the measurements taken from the obverse Government furnished hub or die. 2. -2 and -3 are identical with

8、 the exception of a plastic back plate which is added to designate JROTC. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking

9、permitted without license from IHS-,-,-MIL-DTL-11132/12E Page 3 of 3 Custodians: Preparing activity: Army - IH Army - IH Air Force - 11 Review activity: (Project No. 8455-2013-124) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-