ARMY MIL-DTL-11132 54 B-2009 BADGE QUALIFICATION MARKSMANSHIP MARKSMAN ARMY JROTC《陆军初级预备役军官训练营(JROTC)神射手 神枪手资质徽章》.pdf

1、INCH-POUNDMIL-DTL-11132/54B 10 January 2009 SUPERSEDING MIL-DTL-11132/54A 7 April 2004 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, MARKSMANSHIP, MARKSMAN, ARMY JROTC This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiri

2、ng the product described herein shall consist of this specification sheet and MIL-I-11132. SUSPENSION BAR ASSEMBLED (See Note 2.) PENDANT QUALIFICATION BARS DASH NO. -1: Air Rifle Qualification Bar -2: Small Bore Rifle Qualification Bar MATERIAL: Red Brass FINISH: Nickel Plated, Silver Plated, Oxidi

3、zed, Relieved, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 14. DIMENSIONS: SUSPENSION BAR (JROTC): WIDTH: 1-1/2 inches (REF) HEIGHT (including built-in suspension rings) 5/8 inch (REF) THICKNESS (at thickest point): 0.081 0.005 inch PENDANT (Target): DIAMETER (circumscr

4、ibed; includes top & bottom built-in suspension rings): 1-7/16 inches (REF) AMSC N/A 1 of 2 FSC 8455 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/54B THICKNESS (at thickest point): 0.071 0.005 inch QUALIFICATION BAR (-1 or -2): -1: A

5、IR RIFLE: WIDTH: 1-1/2 inches (REF) HEIGHT (includes top & bottom built-in suspension rings): 1/2 inch (REF) THICKNESS (at thickest point): 0.081 0.005 inch -2: SMALL BORE RIFLE: WIDTH: 1-1/2 inches (REF) HEIGHT (includes top & bottom built-in suspension rings): 1/2 inch (REF) THICKNESS (at thickest

6、 point): 0.081 0.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Badge shall be assembled with either the -1 or the -2 qualification bar. 3. Suspension rings and lugs shall be integral and pierced. 4. Links (jump rings) shall be fabrica

7、ted from nickel plated wire with a nominal diameter of 0.050 1/64 inch. The overall dimension of the links shall be 7/32 inch 1/64 inch in length by 5/32 inch 1/64 inch in width. 5. Attaching device shall be prong and wing-type clutch. Two prongs shall be located on the horizontal center line of the

8、 suspension bar, equidistant from each end and 1-1/4 inches 1/32 inch apart. 6. A forcer may be used to bring up the designs of the suspension bar and pendant. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous is

9、sue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and re

10、lationship to the last previous issue. Custodians: Preparing activity: Army - IH Army - IH (Project No. 8455-2009-033) Review activities: DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. 2 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-