ARMY MIL-DTL-15665 66 C-2010 INSIGNIA SERVICE CAP OFFICERS ARMY MALE AND AIR FORCE MALE AND FEMALE《陆军兵军官和海军男军官和女军官帽徽》.pdf

1、AMSC N/A 1 of 2 FSC 8455 INCH-POUND MIL-DTL-15665/66C 21 January 2010 SUPERSEDING MIL-DTL-15665/66B 19 April 2005 DETAIL SPECIFICATION SHEET INSIGNIA, SERVICE CAP, OFFICERS, ARMY, MALE AND AIR FORCE, MALE AND FEMALE This specification is approved for use by all Departments and Agencies of the Depart

2、ment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-15665. DASH NO. -1: Army (Male only) MATERIAL: -2: Air Force -1: Not less than 85/15 Rich-Low Brass -2: Not less than 85/15 Rich-Low Brass or Nickel

3、Silver FINISH: -1: 24K Gold Plated, Matte Finished, Polished Highlights, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. -2: Nickel Plated, Antiqued with Glossy Black Lacquer and Brightly Polished Highlights DIMENSIONS: HEIGHT (overall): 2-3/8 inches (REF) WIDTH (overall

4、): 2-3/16 inches (REF) THICKNESS (at wing tip and tail feather tips): 0.047 inch + 0.016 inch - 0 inch Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15665/66C 2 of 2 NOTES: 1. The term (REF) refers to measurements taken from the Government

5、furnished hub or die. 2. Pierced areas shall be as indicated. 3. A forcer may be used to bring up the design provided the use of the forcer does not result in a thickness through the shield of less than 0.060 inch. 4. Attaching device for -1 Army and -2 Air Force Male insignia shall be screw post wi

6、th thumb nut and two registering prongs as shown. As an alternate, attaching device for -1 and -2 Male insignia may be screw post with thumb nut and one registering prong centered on the reverse of the cloud (not shown). The registering prong(s) shall be 1/4 inch 1/64 inch in length and 0.045 inch 0

7、.10 inch in diameter. 5. Attaching device for -2 Air Force Female insignia shall be prong and clutch type. The prongs shall be located as shown and be 5/16 inch 1/64 inch in length and 0.045 inch 0.10 inch in diameter. -1 & -2 MALE (Note 4) -2 FEMALE (Note 5) 6. Insignia shall be dapped in the horiz

8、ontal direction along a 4 inch 1/64 inch radius. 7. -1 insignia may be manufactured for commercial sale only using 22 karat gold plate with nickel underplating, matte finish, and polished highlights which shall match TIOH Metal Finish Chip Number 11. CHANGES FROM PREVIOUS ISSUE: Marginal notations a

9、re not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodian: Preparing activity: Army - IH Army - IH Air Force - 11 Review activities: (Project No. 8455-2010-028) DLA - CT NOTE: The activities listed above were interested in this do

10、cument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-