ARMY MIL-DTL-32235 3-2010 HEATER MODULE BOIL-IN-BAG (BIB) MODULE.pdf

1、 MIL-DTL-32235/3 15 September 2010 INCH-POUND DETAIL SPECIFICATION SHEET HEATER MODULE, BOIL-IN-BAG (BIB) MODULE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this spec

2、ification sheet and MIL-DTL-32235. REQUIREMENTS I. Boil-In-Bag (BIB) module. The BIB module shall consist of a fiberboard box containing one BIB of dry or dehydrated food packaged in a barrier pouch, one pouch of potable water for rehydrating the food, one heater packaged in a barrier pouch, one act

3、ivation fluid unit, and one serving tray in a polyethylene bag. Note that the terms bag and pouch are used interchangeably. A. Heater. The heater shall be constructed of materials that, when activated by a fluid, shall initiate and propagate an exothermic reaction suitable for use with food. This re

4、action shall generate adequate heat to completely cook the food when applicable, or heat the food to a safe serving temperature. No toxic gas, liquid or solid by-products are desirable. If toxic by-products are produced, they shall be of the least severity and smallest amount possible while allowing

5、 for adequate heating and ensuring operator and consumer safety. The heater material shall be evenly distributed and completely sealed within the scrim matrix of the heater to minimize the release of materials, and facilitate direct in-place activation of the heater materials. The heating rate shall

6、 be optimized to minimize the time required to heat the food, yet not cause excessive foaming or uncontrolled release of reaction by-products. The heater and barrier material shall not melt, deform or degrade during heating. The heater is activated by the addition of a fluid that shall fully activat

7、e the heater material. The non-woven porous polymeric scrim shall be sealed and sized to accommodate proper fit and function of the heater module. Each heater (heater elements in a matrix) shall be correctly and legibly labeled in accordance with MIL-DTL-32235. AMSC N/A FSC 8970 Provided by IHSNot f

8、or Resale-,-,-MIL-DTL-32235/3 2One heater shall be packaged in a barrier pouch constructed from laminated material, with one lamina a minimum of 0.00035 inch thick aluminum foil. The pouch shall be heat sealed on all four edges. A tear nick, notch or serrations shall be provided to facilitate openin

9、g of the filled and sealed barrier pouch. The barrier pouch shall have maximum outer dimensions of 11 by 15 inches. Each pouch with heater shall be correctly and legibly labeled in accordance with MIL-DTL-32235. B. Activation fluid unit. The activation fluid unit consisting of a pouch containing the

10、 activation fluid shall be made of material equivalent to Class 1 of MIL-PRF-131. Alternate activation fluid unit materials and design shall be permitted with approval from Natick Soldier Research, Development and Engineering Center. The pouch shall be designed with a center or side spout and shall

11、have maximum outer dimensions of 9-1/2 by 14 inches. The pouch shall be filled with 1.5 percent saline (water and sodium chloride) solution, or as specified by the heater manufacturer with approval from Natick Soldier Research, Development and Engineering Center. The volume of fluid in the pouch, wh

12、en combined with the heater, shall be adequate to initiate and propagate the exothermic reaction. The pouch shall be heat sealed on all edges. A tear nick, notch or serrations shall be provided in the spout area to facilitate opening of the filled and sealed pouch. The average seal strength of the c

13、losure seal shall be not less than 6 pounds per inch of width and no individual specimen shall have a seal strength of less than 5 pounds per inch of width. Alternatively, the filled and sealed pouch shall exhibit no rupture or seal separation greater than 1/16 inch or seal separation that reduces t

14、he effective closure seal width to less than 1/16 inch when tested for internal pressure resistance. Each activation fluid unit shall be correctly and legibly labeled in accordance with MIL-DTL-32235. In addition, the following statement shall be labeled on the pouch: DO NOT CONSUME C. Boil-In-Bag (

15、BIB). The BIB of food shall meet the requirements of the applicable food document. Note that the eggs in a BIB are cited in PCR-E-017. D. Rehydration water pouch. Water shall conform to all requirements of A-A-20332. The water shall be sterilized by either class 1 (thermoprocessed), class 2 (ozone)

16、or class 3 (ultraviolet light) treatment. The pouch containing the rehydration water shall be made of material equivalent to Class 1 of MIL-PRF-131. The pouch shall have maximum outer dimensions of 9-1/2 by 14 inches. The minimum volume of rehydration water in the pouch shall be 1.5 liters (51 fl. o

17、z.). The pouch shall be fitted with a cap with a 3/4 inch opening and a tamper evident closure. The pouch shall not leak. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSMIL-DTL-32235/3 3The pouch shall be heat sealed on all edges. The average seal streng

18、th of the closure seal shall be not less than 6 pounds per inch of width and no individual specimen shall have a seal strength of less than 5 pounds per inch of width. Alternatively, the filled and sealed pouch shall exhibit no rupture or seal separation greater than 1/16 inch or seal separation tha

19、t reduces the effective closure seal width to less than 1/16 inch when tested for internal pressure resistance. Each pouch shall be correctly and legibly labeled. The label shall contain the following information: (1) Name (2) Contents (3) Net volume (4) Date 1/ (5) Contractors name and address 1/ E

20、ach pouch shall have the date of pack noted by using a four digit code beginning with the final digit of the current year followed by the three digit Julian day code. For example, 14 February 2011 would be coded as 1045. The Julian day code shall represent the day the water was packaged. E. Serving

21、tray. The serving tray shall be constructed from food grade (direct food contact), water resistant paperboard. All inside surfaces and edges shall be coated. The serving tray shall be capable of containing the food product during the preparation, cooking and serving of the food. There shall be no pr

22、oduct transfer in or out of serving tray. The dimensions shall be a maximum of 14-1/2 by 10 by 2 inches. The serving tray shall be placed in a polyethylene bag with dimensions of approximately 24 by 16 inches and the bag sealed. The polyethylene bag shall be labeled with: SERVING TRAY DO NOT DISPOSE

23、 REMOVE BAG BEFORE USING F. Fiberboard box. The fiberboard box shall be constructed from C flute corrugated fiberboard. The inside of the box shall be coated with a food grade (direct food contact), water resistant coating. The design of the box shall be a flip top box with a locking mechanism. The

24、outside dimensions shall be a maximum of 15-1/2 by 11 by 2-3/4 inches. The fiberboard box shall maintain its shape and integrity while containing the activated, heated, and cooked or serve-temperature BIB food for a minimum of 90 minutes after the heating reaction is initiated. Provided by IHSNot fo

25、r Resale-,-,-MIL-DTL-32235/3 4G. Assembly of BIB module. The BIB module shall consist of one fiberboard box containing one BIB of food, one pouch of rehydration water, one activation fluid unit, one packaged heater, one serving tray in a polyethylene bag, and instruction sheets. All components shall

26、 be compatible and shall fit in the module box. Each heater module shall be correctly and legibly labeled in accordance with MIL-DTL-32235. EXAMINATION A. BIB heater module examination. The finished product shall be examined for compliance with the requirements specified in MIL-DTL-32235 and this sp

27、ecification sheet. The BIB heater module shall be examined for the defects listed in Table I. TABLE I. BIB heater module defects 1/ 2/ Category Defect Major Minor 101 Heater module not a BIB heater module. 102 Heater does not contain materials that will initiate and propagate an exothermic reaction.

28、 103 Heater causes excessive foaming or uncontrolled release of reaction by-products. 104 Heater not correct size or not correct capacity. 105 Heater module does not generate adequate heat to completely cook the food or heat the food to a safe serving temperature, as applicable. 201 Tear nick, notch

29、 or serrations on heater barrier pouch missing or does not facilitate opening. 106 Heater not packaged in a barrier pouch. 202 Tear nick, notch or serrations on activator fluid pouch missing or does not facilitate opening. 107 Rehydration water pouch leaks. 108 Serving tray not correct dimensions or

30、 not correct design. 109 Serving tray not in polyethylene bag. Provided by IHSNot for Resale-,-,-MIL-DTL-32235/3 5TABLE I. BIB heater module defects 1/ 2/ - Continued Category Defect Major Minor 203 Fiberboard module box not correct dimensions or not correct design. 204 Fitment on pouch of rehydrati

31、on water not compatible with BIB. 205 Components not compatible or do not fit in fiberboard module box. 206 Fiberboard box does not maintain its shape and integrity while containing the activated, heated, and cooked or serve-temperature BIB food for a minimum of 90 minutes after the heating reaction

32、 is initiated. 1/ Requirements that rehydration water meets A-A-20332 shall be verified by Certificate of Conformance (CoC). 2/ Serving tray construction from fiberboard with a food grade water resistant coating shall be verified by CoC. II. Notes. A. Part identifiers and sources of supply. 1. Heate

33、r. The heater is available from: Truetech Inc. 680 Elton Ave. Riverhead, NY 11901-2585 (631) 727-8600 2. Heater barrier pouch. The barrier pouch material is available from: Winter-Wolff International 131 Jericho Turnpike Jericho, NY 11753 (516) 997-3300 Provided by IHSNot for Resale-,-,-MIL-DTL-3223

34、5/3 63. Activation fluid unit. The material CADPACK N for the construction of the activation fluid unit pouch is available from: Cadillac Products 5800 Crooks Road Troy, Michigan 48098-2830 (248) 813-8200 The filled and sealed activation fluid units are available from: Heritage Packaging 625 Fishers

35、 Run Victor, NY 14564 (585) 742-3310 4. Thermocoupled BIBs. Filled thermocoupled BIBs or instructions on how to construct them are available from: US Army Research, Development and Engineering Command Natick Soldier Research, Development, and Engineering Center RDNS-CEG 15 Kansas Street Natick, MA 0

36、1760-5056 (508) 233-4939 5. Instruction sheets. The following operation instruction sheets are attached: FIGURE 1. BIB Module Operating Instructions, for Heater with Hydrogen Generating Warning FIGURE 2. BIB Module Operating Instructions, for Heater with No Hydrogen Generation Warning Instruction sh

37、eets in color are available electronically from: US Army Research, Development and Engineering Command Natick Soldier Research, Development and Engineering Center RDNS-CEG 15 Kansas Street Natick, MA 01760-5056 (508) 233-6252 Provided by IHSNot for Resale-,-,-MIL-DTL-32235/3 7B. References. MIL-PRF-

38、131 - Barrier Materials, Watervaporproof, Greaseproof, Flexible, Heat-Sealable A-A-20332 - Water, Emergency, Drinking (Copies of these documents are available from https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Ave, Building 4D, Philadelphia, PA

39、19111-5094.) PCR-E-017 - Egg Mix, Pasteurized, Uncooked, Dehydrated, Packaged in a Boil-In-Bag (BIB) (Copies of this document are available online at ray.valvanous.army.mil or from U.S. Army Research, Development and Engineering Command, Natick Soldier Research, Development and Engineering Center, R

40、DNS-CFF, 15 Kansas St., Natick, MA 01760-5056) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSMIL-DTL-32235/3 8FIGURE 1. BIB Module Operating Instructions, for Heater with Hydrogen Generating Warning Provided by IHSNot for Resale-,-,-MIL-DTL-32235/3 9FIG

41、URE 2. BIB Module Operating Instructions, for Heater with No Hydrogen Generation Warning Provided by IHSNot for Resale-,-,-MIL-DTL-32235/3 10Custodians: Preparing activity: Army GL Army GL Navy SA (Project 8970-2010-004) Air Force 35 Review Activities: Army MD, QM Navy MC DLA SS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for Resale-,-,-