ARMY MIL-DTL-3476 J-1998 BRASSARD GENERAL SPECIFICATION FOR《臂章的一般规定》.pdf

1、MIL-DTL-347bJ - 9999906 207b77L 701 I NOT MEASUREMENT SENSITIVE 1 MI L-DTL-3476 J 21 October 1998 SUPERSEDING 10 May 1991 M IL-B-3476H DETAIL SPECIFICATION BRASSARDS, GENERAL SPECIFICATION FOR This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCO

2、PE 1.1 Scope. This specification covers the general requirements for brassards used by the Department of Defense (see 6.1). 1.2 Classification. Brassards covered by this specification shall be as specified on the applicable military specification sheet and Supplement I (see 2.1 and 6.2). 2. APPLICAB

3、LE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to

4、ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2. I SDecifications. standards. and handbooks. The following specif

5、ications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense index of Specifications and Standards (DoDISS) and supplement thereto, cited in the soli

6、citation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in preparing this document should be addressed to: Director, The Institute of Heraldry, US Army, 9325 Gunston Road, Room SI 12, Fort Belvoir, VA 22060-5579, by using the Standar

7、dization Document Improvement Proposal (DD Form 1426) appearing at the end of this document. AMSC N/A FSC 8455 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. I Licensed by Information Handling ServicesMIL-DTL-347bJ = 9999906 2076772 648 MIL-DTL3476J SPECIFICATIONS

8、FEDERAL A-A-52094 - Thread, Cotton DEPARTMENT OF DEFENSE MIL-DTL-14652 - Insignia, Embroidered, Organizational, Insignia and Badges, General Specification For STANDARDS FEDERAL FED-STD-191 - Textile, Test Methods FED-STD-751 - Stitches, Seams and Stitching SPECIFICATION SHEETS (See Supplement 1 for

9、list of specification sheets.) (Unless otherwise indicated, copies of the above specifications, standards and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 Il -5094.) 2.2.2 Other Gove rnment documents. drawinas and publica

10、tions. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS THE INSTITUTE OF HERALDRY 8-8-42 - Brassard, Location of Dot Fasteners B-8-42A

11、 - Brassard, Location of Dot Fasteners B-8-61 - Brassard, Location of Hook and Loop Fasteners (Figures i, 2, and 3 are miniature reproductions of the referenced drawings and are for information only. Copies of specifications, standards, drawings and specification sheets required by the contractors i

12、n connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of

13、the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2) 2 Licensed by Information Handling Services MIL-

14、DTL-347bJ 999Ob 2076773 584 MIL-DTL-3476J (Non-government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other information services.) AMERICAN SOCIETY FOR QUALIT

15、Y CONTROL ANSVASQC Z1.4, 1993 - Sampling Procedures and Tables for Inspection by Attributes (Application for copies of ANSVASQC Z1.4 should be addressed to the American Society for Quality Control, 61 1 East Wisconsin Avenue, Milwaukee, Wisconsin 53202.) MERIT RIBBON COMPANY DoD Standard Shades for

16、Heraldic Yarns for Embroidery and Ribbon, 1993 Edition (Application for copies of the DoD Standard Shades for Heraldic Yarns for Embroidery and Ribbon should be addressed to Merit Ribbon Co., Inc., 30 Davids Drive, Hauppauge, NY 1 1788.) THE COLOR ASSOCIATION OF THE UNITED STATES The Standard Color

17、Reference of America, Tenth Edition United States Army Color Card, The Official Colors for Branches, Agencies, etc. (Application for copies of the color card and the U.S. Army Color Card should be addressed to the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016- I 18

18、7.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated specifications or specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws

19、and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be as specified herein and in accordance with the applicable specification sheet. In the event of any conflict between the requirements of this specificatio

20、n and the specification sheet, the latter shall govern. 3.2 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.3. 3.3 Recvcled. recovered, or environmentallv preferable materials. Recycled, recovered, or environmentally preferable ma

21、terials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economical advantageous life cycle costs. 3.4 Material. The material shall be as specified herein. 3 Licensed by Information Handling ServicesM

22、IL-DTL-3476 J 3.4.1 Percale. The percale shall be a preshrunk 100% cotton plain weave fabric conforming to the physical requirements listed below. The color shall conform to the cable number specified on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. We

23、ight per square yard (ounces): Yarns per inch (minimum): Breaking strength, minimum (pounds): Weave: Plain 3 minimum Warp 85, Filling 72 Warp 45, Filling 30 3.4.2 Wool broadcloth or facina cloth. The wool broadcloth or facing cloth shall be a mothproofed 100% wool or 80% wool, 20% polyester blend fa

24、bric conforming to the physical requirements listed below. The color shall conform to the cable number specified on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. a. 100% Wool Weight per square yard (ounces): Yarns per inch (minimum): Breaking strength,

25、 minimum (pounds): Weave: 16 minimum Warp 60, Filling 58 Warp 40, Filling 35 2 up, I down right hand twill b. 80/20% WooVPolyester Weight per square yard (ounces): Yams per inch (minimum): Breaking strength, minimum (pounds): Weave: 16 minimum Warp 51, Filling 51 Warp 55, Filling 45 2 up, 1 down rig

26、ht hand twill 3.4.3 Wool felt. The wool felt shall be a mothproofed 100% pressed wool fabric conforming to the physical requirements listed below. The color shall conform to the cable number specified on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. Th

27、ickness (inches): Weight per square yard (ounces): Breaking strength (pounds): 30 minimum Nominal 0.063, min. - 0.053, max. - 0.073 Nominal 12, minimum 1 1 , maximum 13 3.4.4 Cloth. cotton. uniform twill. The cotton uniform twill cloth shall be a preshrunk 100% white cotton twill conforming to the p

28、hysical requirements of any of the following type materials: a. Type1 Yam: Combed Ply: Warp 2, Filling 2 Weight per square yard (ounces): Yams per inch (minimum): 7.9 minimum, 8.6 maximum Warp 116, Filling 56 4 Licensed by Information Handling ServicesMIL-DTL-347bJ 7777906 207b775 357 MIL-DTL-3476J

29、Breaking strength (pounds): Weave: 3/1 right hand twill Warp 180, Filling 120 b. Type II Yarn: Combed Ply: Warp 2, Filling 1 Weight per square yard (ounces): Yarns per inch (minimum): Breaking strength (pounds): Weave: 3/1 right hand twill 7.9 minimum, 8.6 maximum Warp 116, Filling 56 Warp 180, Fill

30、ing 110 c. Type III Yarn: Com bed Ply: Warp 1, Filling I Weight per square yard (ounces): Yarns per inch (minimum): Breaking strength (pounds): Weave: 3/1 left hand twill 7.7 minimum, 8.4 maximum Warp 112, Filling 54 Warp 160, Filling 110 d. Type IV Yarn: Combed Ply: Warp 1, Filling 1 Weight per squ

31、are yard (ounces): Yarns per inch (minimum): Breaking strength (pounds): Weave: 3/1 left hand twill 7.2 minimum, 7.9 maximum Warp 100, Filling 54 Warp 160, Filling I10 e. TypeV Yarn: Carded Ply: Warp I, Filling 1 Weight per square yard (ounces): Yarns per inch (minimum): Breaking strength (pounds):

32、Weave: 3/1 left hand twill 7.2 minimum, 7.9 maximum Warp 100, Filling 54 Warp 150, Filling 100 f. TypeVI Yarn: Carded Ply: Warp 1, Filling 1 Weight per square yard (ounces): Yarns per inch (minimum): Breaking strength (pounds): Weave: 3/1 left hand twill 8.2 minimum, 8.6 maximum Warp 112, Filling 56

33、 Warp 170, Filling 80 3.4.5 Cloth. wool serge. The wool shall be a mothproofed 100% wool serge conforming to the physical requirements listed below. The color shall conform to the shade or cable 5 Licensed by Information Handling Services MIL-DTL-347bJ 999990b 207b77b 293 MI L-DTL-3476J number speci

34、fied on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. Weight per square yard (ounces): Ply: Warp 2, Filling 2 Yarns per inch (minimum): Breaking strength (pounds, minimum): Shrinkage (maximum): Weave: 18 minimum Warp 68, Filling 54 Warp 1 IO, Filling 1

35、00 Warp 4.0%, Filling 2.5% 2 up, 2 down, 4 harness right twill 3.4.6 Cloth. wool melton. The wool shall be a mothproofed melton conforming to the physical requirements of any of the following type materials listed below. The color shall conform to the shade or cable number specified on the applicabl

36、e specification sheet. Colorfastness shall conform to the requirements of 3.7.2. a. Type1 Weight per square yard (ounces): Yams per inch (minimum): Breaking strength (pounds, minimum): Weave: 16 minimum, 17 maximum Warp 60, Filling 55 Warp 58, Filling 46 2 up, 1 down right hand twill b. Type II Weig

37、ht per square yard (ounces): Yams per inch (minimum): Breaking strength (pounds, minimum): Weave: 22 minimum, 24 maximum Warp 55, Filling 45 Warp 80, Filling 60 3 up, 1 down crowfoot 3.4.7 Cloth. duck. nvlon. The nylon duck shall be a bright high tenacity nylon filament of both warp and filling conf

38、orming to the physical requirements listed below. The color shall conform to the shade or cable number specified on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. Weight per square yard (ounces): Yams per inch (minimum): Ply Warp 2, Filling 2 Breaking s

39、trength (pounds, minimum): Weave: 7.25 minimum Warp 60, Filling 45 Warp 325, Filling 275 Plain, 1 up and I down 3.4.8 mram. The buckram shall be a light, open-weave, single ply fabric conforming to the following physical requirements: Weight per square yard (ounces): Yarns per inch (minimum): Breaki

40、ng strength (pounds, minimum): 2.5 minimum Warp 40, Filling 20 Warp 30, Filling 20 3.4.9 m. The tape shall be 100% cotton, 318 inch (0.95 cm) in width and conform to the physical requirements listed below. The tape shall be black in color. Colorfastness shall conform to the requirements of 3.7.2. 6

41、Licensed by Information Handling ServicesNIL-DTL-347bJ - 0b 2076777 L2T M M IL-DTL-3476J Weight per square yard (ounces): Yarns (minimum): Yarns per inch (minimum): 0.01 3 minimum Face and Back Warp - 37 Binder Warp - 7 42 yarns per inch (I yarn per shed) of 20/2 ply, or 84 yarns per inch (2 yarns p

42、er shed) of 4012 ply 50 warp (full width) Breaking strength (pounds, minimum): 3.4.10 Elastic webbinq. Yarn for the elastic webbing shall be 100% cotton. The elastic strands shall be made of compounded natural rubber, synthetic rubber, or a mixture thereof. The color shall conform to the shade or ca

43、ble number specified on the applicable specification sheet. Colorfastness shall conform to the requirements of 3.7.2. The webbing shall be composed of one ground warp and one elastic warp (with strands wrapped) and one filling. The ground warp shall weave in a two up and two down order and the elast

44、ic warp shall weave in such a manner as to be over all the back picks and under all the face picks. The elastic webbing shall meet the following physical requirements: Width: Thickness: Weight per square yard (ounces): Yarns (full width)(minimum): Yarns per inch (minimum): Elastic strands gage (per

45、inch, maximum fineness): 1-1/4 inches (3.175 cm) f 1/16 inch (0.159 cm) 0.050 inch - 0.65 inch (O. 127 cm - O. 165 cm) 0.54 minimum Ground Warp - 26 Elastic Strands - 14 52 filling 50 3.4.1 I Ink. The ink for marking and stenciling shall be an indelible marking ink. Colorfastness shall conform to th

46、e requirements of 3.7.2. 3.4.12 Snap fasteners. Snap fasteners shall be any type brass or steel, pronged ring head type, size 17 ligne with a black or nickel plate finish. Black fasteners shall be used on dark background brassards. Nickel plate fasteners shall be used on white brassards only. 3.4.13

47、 Safety pins. Safety pins shall be 1-1/16 inches (2.699 cm) 5 1/16 inch (0.159 cm) pin without guard manufactured from brass or stainless steel. 3.4.14 Thread. The cotton thread shall conform to A-A-52094. The size and color shall be as specified on the applicable specification sheet. 3.4.15 Embroid

48、ery yarn. The embroidery yarn shall be a semi-dull continuous filament, regenerated cellulose type rayon, two-ply Schiffli type yarn. The yam shall be 150, 100 or 75 denier as specified on the applicable cartoon or drawing. Unless otherwise specified, the use of two-ply polyester is authorized in li

49、eu of rayon. When polyester yam is used, 135 denier will be substituted for 150 denier, 90 denier will be substituted for 1 O0 denier, and 70 denier will be substituted for 75 denier rayon. 3.4.15.1 Color. The color of the embroidery yarn shall be as specified on the applicable drawing or cartoon. When overedge stitching is required, the color shall be the same as the embroidered border. The use of sulfur dyes is prohibited (see 3.4.17. I). 7 Licensed by Information Handling ServicesMIL-DTL-347bJ = 9999906 207b778 066 MIL-DTL-3476J 3.4.15.2 Mac. The color shall be a good match to