ARMY MIL-DTL-3628 137A-2000 BADGE IDENTIFICATION POLICE DEFENSE PROTECTIVE SERVICE OFFICE OF THE SECRETARY OF DEFENSE.pdf

1、AMSC N/ A 1 of 3 FSC 8455DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.INCH-POUNDMIL-DTL-3628/137A21 September 2000SUPERSEDINGMIL-DTL-3628/13715 November 1996DETAIL SPECIFICATION SHEETBADGE, IDENTIFICATION, POLICE, DEFENSE PROTECTIVE SERVICE,OFFICE OF THE SECRETAR

2、Y OF DEFENSEInactive for new design after 13 January 1999.This specification is approved for use by all Departments and Agenciesof the Department of Defense.The requirements for acquiring the product described herein shall consist of thisspecification sheet and the issue of MIL-DTL-3628 listed in th

3、at issue of the Department ofDefense Index of Specifications and Standards ( DoDISS) specified in the solicitation.MATERIAL: Gilding MetalFINISH: Hard Enameled, Soft Baked Enameled, Gold Plated, Mirror-like Polished andshall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 6.Provided

4、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/137A2 of 3DIMENSIONS:HEIGHT (overall) : 3-1/2 inches (REF)WIDTH (overall) : 2-1/4 inches (REF)THICKNESS (at “POLICE“ lettering) : 0.085 inch 0.010 inchNOTES:1. The term (REF) refers to the measureme

5、nts taken from the Government furnishedhub or die. TIOH Drawing Numbers B-16-9 and B-16-9A may be used as additionalreference.2. A full forcer shall be used to bring up the details of the design.3. Piercing shall be as indicated.4. The badge shall be dapped to a radius of 3-3/8 inch 1/4 inch along t

6、he horizontalplane.5. Epoxy resin (stoning epoxy) may be used in lieu of both hard enamel and softbaked enamel at the option of the manufacturer. When epoxy resin is used in lieu of softbaked enamel , the epoxy resin shall not be stoned. Enamel and epoxy colors shallconform to TIOH Hard Enamel Chip

7、Numbers listed below:COLOR CHIP NUMBERGreen 12Black 26Blue 336. Scroll lettering shall be as specified in the procurement document and may be cutinto the working die or the badge. Letters shall be 1/8 inch in height, block style, and filledwith black soft baked enamel or unstoned epoxy.7. The attach

8、ing device shall be a coil pin type with heavy-duty side opening catch.The pin stem shall be 2 inches 1/64 inch long. The pin and catch shall be hard solderedor fused on the vertical center line with the joint located 3/4 inch 1/64 inch down fromthe top of the badge. The joint and catch shall be pos

9、itioned on the same level plane toeach other. (Platform areas on the reverse side may be used for leveling the joint andcatch.)8. Each badge shall be numbered consecutively with the number specified in theprocurement document. Numbers shall be 1/8 inch high, engraved, equally spaced, andaligned in a

10、n arc within the unembossed area provided on the lower obverse side.Numbers shall be filled with black soft baked enamel or unstoned epoxy.CHANGES FROM PREVIOUS ISSUE : Marginal notations are not used in this revision toidentify changes with respect to the previous issue due to the extent of the cha

11、nges.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/137A3 of 3Custodian: Preparing activity:Army - IH Army - IHReview activity: (Project No. 8455-0027)DLA - CTProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-