1、AMSC N/A Page 1 of 3 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, PISTOL, U.S. MARINE CORPS, PENDANT AND SUSPENSION BAR This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall
2、consist of this specification sheet and the latest issue of MIL-DTL-3628. Pierced Pebbled Background EXPERT -1 SHARPSHOOTER -2 MARKSMAN -3 DASH NO. -1: Expert -2: Sharpshooter -3: Marksman MATERIAL (-1 through -3): Red Brass 85/15 (UNS Alloy No.C-230), Nickel Silver 65/15 (UNS Alloy No.C-752) or Zin
3、c Aluminum. INCH-POUND MIL-DTL-3628/17J 10 December 2012 SUPERSEDING MIL-DTL-3628/17H 15 November 1996 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/17J Page 2 of 3 FINISH: 1.Red Brass 85/15(UNS Alloy No. C-230): or Nickel Silver, Nick
4、el Plated ,Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16 except Textured Background Areas which shall be lightly Polished. 2. Zinc Aluminum: Copper Plated, Nickel Plated, Mirror-like Polished and shall match TIOH Metal Finish Chip Number 16 except
5、Textured Background Areas which shall be lightly Polished. DIMENSIONS: PENDANT: HEIGHT (Overall): -1: 5/16 inch (REF) -2: 1-5/32 inches (REF) -3: 1-1/32 inches (REF) WIDTH (Overall) -1: 1-1/32 inches (REF) -2: 1 inch (REF) -3: 7/8 (REF) THICKNESS: -1: 0.115 inch + 0.005 inch (At thickest point) -2:
6、0.075 inch + 0.005 inch (At edge) -2: 0.160 inch + 0.005 inch (Total ) -3: 0.070 inch + 0.005 inch (At center) SUSPENSION BAR: HEIGHT (Overall): 7/32 inch (REF) WIDTH (Overall): 1-15/32 inches (REF) THICKNESS (At edge): 0.070 inch + 0.005 inch ATTACHING DEVICE & PIERCING: 1. The attaching device sha
7、ll be prong and clutch type. 2. The prongs shall be located on the horizontal center line on the back of the suspension bar equidistant from each end and 1-3/16 inches + 1/32 inch apart. 3. The Marine Corps emblem shall be circumscribed in a 3/8 inch diameter circle and shall be soft soldered to the
8、 target area of the cross for -2 after trimming and piercing. 4. Piercing shall be as indicated for -1 only. 5. Links shall be 13/64 inch + 1/64 inch in width and 1/4 inch + 1/64 in length and shall be fabricated from 0.044 inch + 0.005 inch diameter wire. 6. Lugs for bar and pendant are integral. P
9、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/17J Page 3 of 3 NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. The specification slash sheet for the Qualification clasps used with -1
10、 is MIL-DTL-3628/18. 3. Badge may be rhodium plated with a Nickel Plated, Mirror-like Polished shall match the TIOH Metal Finish Chip Number 16 at the option of the manufacturer. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the pre
11、vious issue due to the extent of the changes. Custodians: Preparing activity: Army - IH Army - IH Navy - MC Review activity: (Project No. 8455-2013-009) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1