ARMY MIL-DTL-3628 249-2009 BADGE RECRUITING AND RETENTION ARMY NATIONAL GUARD《陆军国民警卫队招募和选留徽章》.pdf

1、INCH-POUND MIL-DTL-3628/249 20 February 2009 DETAIL SPECIFICATION SHEET BADGE, RECRUITING AND RETENTION, ARMY NATIONAL GUARD This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist

2、of this specification sheet and the latest issue of MIL-DTL-3628. GREEN- in letters and around stars in inner ring GREEN- wreath, in letters and around stars in inner ring BASIC SENIOR EXPERT DASH NO: -1: Basic -2: Senior -3: Expert MATERIAL: Gilding Metal or Red Brass FINISH: -1: Nickel Plated Mirr

3、or-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 16. Enamel/Epoxy (TIOH) color chip #11 Transparent Green. -2, -3: Base Plate and Minute Man Device, 24K Gold Plated, Mirror-like Polished and shall match (TIOH) Metal Finish Chip Number 6. Designation Plate, N

4、ickel Plated Mirror-like Polished and shall match (TIOH) Metal Finish Chip Number 16. Enamel/Epoxy (TIOH) Color Chip #11 Transparent Green. DIMENSIONS: HEIGHT (overall): -1: 2-5/16 inch circumscribed (REF) -2: 2-9/16 inch (REF) -3: 2-11/16 inch (REF) AMSC N/A 1 of 2 FSC 8455 Provided by IHSNot for R

5、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/249 WIDTH (overall): -1: 2-5/16 inches circumscribed (REF) -2,-3: 2-1/2 inches (REF) THICKNESS (at thickest point): -1: 0.190 0.01 inch -2,-3: 0.260 0.01 inch NOTES: 1. The term (REF) refers to the measurements ta

6、ken from the Government furnished hub or die. 2. Attaching device shall be prong and flat ball clutch type. For -1: three prongs shall be located on the reverse two at the top on a horizontal plane 1-11/16 1/32 inches apart and one prong in base centered vertically between the top two 1-1/2 1/32 inc

7、hes below. For -2,-3: three prongs shall be located on the reverse one at the top in the center, and two 1-1/2 1/32 inches below on a horizontal plane 1-7/16 1/32 inches apart. 3. These badges may be manufactured with a dull, flat black enamel finish and shall match FED-STD-595, Chip Number 37038 or

8、 TIOH Metal Finish Chip #21 Dull Flat Black. 4. A forcer maybe used to bring up the detailing in the base plates and the designation plate. 5. Enameled/epoxied areas shall be transparent green. The color shall conform to TIOH Hard Enamel Color Chip Number 11. When hard enamel is used, the material r

9、equirement shall be gilding metal. When epoxy is used, the material requirement shall be gilding metal or red brass. 6. At the option of the manufacturer for commercial sale only, for -2, -3 the Base Plate and Minute Man Device may be manufactured using 22 karat gold plate mirror-like polish to matc

10、h TIOH Metal Chip Number 9. Custodian: Preparing activity: Army - IH Army - IH (Project No. 8455-2009-050) Review activities: DLA CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. 2 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-