ARMY MIL-DTL-3628 254 A-2013 BADGE OCCUPATIONAL CYBERSPACE SUPPORT U S AIR FORCE.pdf

1、AMSC N/A Page 1 of 3 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, OCCUPATIONAL, CYBERSPACE SUPPORT, U.S. AIR FORCE This specification is approved for use by all Departments and Agencies of the Department of Defense The requirements for acquiring the product described herein shall consist of this speci

2、fication sheet and the latest issue of MIL-DTL-3628. P I ER CE D P I E R CE DP I E R C E DP I ER CE DP IE RC EDBASIC SENIOR P I E R C E DP IE RC ED P I ER CE DP I E R C E DMASTER DASH NO: INCH-POUND MIL-DTL-3628/254A 3 September 2013 SUPERSEDING MIL-DTL-3628/254 3 March 2010 -1 Basic, Regular Size -

3、4 Basic, Miniature Size -2 Senior, Regular Size -5 Senior, Miniature Size -3 Master, Regular Size -6 Master, Miniature Size Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/254A Page 2 of 3 MATERIAL: Red Brass 85/15 (UNS Alloy C-230) or N

4、ickel Silver 65/35 (UNS Alloy C-752) FINISH: Nickel Plated (Red Brass only), Mirror-like Polished and shall match The Institute of Heraldry Metal Finish Chip Number 16 DIMENSIONS: HEIGHT (overall): WIDTH (Overall): -1, -2, -3: 1-21/32 inches (REF) -4, -5, -6: 1-17/64 inches (REF) THICKNESS (At thick

5、est point): -1, -2, -3: 0.115 inch + .005 inch -4, -5, -6: 0.098 inch + .005 inch ATTACHING DEVICE: 1. Attaching device shall be prong and clutch type. 2. Two prongs shall be located on the reverse on the horizontal center line The prongs shall be located on the horizontal center line, equidistant f

6、rom each end 1-3/8 inches + 1/32 inch apart on -1, -2, -3 and 1-1/16 inches + 1/32 inch apart on -4, -5, -6. NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Piercing shall be as indicated. 3. A forcer may be used to bring up only the detail of t

7、he gauntlet. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidd

8、ers and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. -1: 25/32 inch (REF) -4: 39/64 inch (REF) -2: 1-5/64 inches (REF) -5: 27/32 inch (REF) -3: 1-7/32 inches (RE

9、F) -6: 15/16 inch (REF) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/254A Page 3 of 3 Custodians: Preparing activity: Army - IH Army - IH Air Force - 11 Review activities: (Project No. 8455-2013-184) Air Force - 99 DLA - CT NOTE: The

10、activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-