ARMY MIL-DTL-3628 3 G-2010 BADGE QUALIFICATION DISTINGUISHED MARKSMAN NAVY PENDANT AND SUSPENSION BAR《海军杰出的神射手资质徽章用挂条》.pdf

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, DISTINGUISHED MARKSMAN, NAVY; PENDANT AND SUSPENSION BAR This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein sha

2、ll consist of this specification sheet and the latest issue of MIL-DTL-3628. MATERIAL: PENDANT: Gilding Metal SUSPENSION BAR: Red Brass FINISH: PENDANT: Hard Enameled, 24K Gold Plated, Matte Finish, Highlights and Rim Polished, and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Numbe

3、r 8. REVERSE - 24K Gold Plated Mirror-like Polished and shall match TIOH Metal Finish Chip Number 6. SUSPENSION BAR: 24K Gold Plated, Matte Finish, Highlights and Rim Polished, and shall match TIOH Metal Finish Chip Number 8. REVERSE - 24K Gold Plated Mirror-like Polished and shall match TIOH Metal

4、Finish Chip Number 6.INCH-POUND MIL-DTL-3628/3G 5 February 2010 SUPERSEDING MIL-DTL-3628/3F 15 November 1996 SCORED BACKGROUND #28 #26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/3G Page 2 of 2 DIMENSIONS: HEIGHT (overall): 1-33/64 i

5、nches (REF) WIDTH (overall): 1-9/32 inches (REF) THICKNESS (edge): 0.080 inch + 0.005 inch SUSPENSION BAR: HEIGHT (overall): 5/16 inch (REF) WIDTH (overall): 1-7/8 inches (REF) THICKNESS (edge): 0.055 inch + 0.005 inch NOTES: 1. The term (REF) refers to the measurements taken from the Government fur

6、nished hub or die. 2. Enameled areas shall be as indicated. The color shall conform to TIOH Enamel Color Chip Numbers listed below. COLOR CHIP NUMBER Black 26 White 28 3. Epoxy resin (stoning epoxy) may be used in lieu of hard enamel at the option of manufacturer. Epoxy resin shall be smooth and flu

7、sh with the dikes. 4. The links shall be fabricated from gold plated wire with a nominal diameter of 0.044 inch + 1/64 inch. The overall dimension of the links shall be 13/64 inch + 1/64 inch in width and 1/4 inch + 1/64 inch in length. 5. The lugs are integral. 6. The attaching device shall be a pr

8、ong and flat ball clutch type. The prongs shall be located on the horizontal center line of the suspension bar, equidistant from each end and 1-11/32 inches + 1/32 inch apart. 7. The use of any type of plastic packaging material is prohibited. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not

9、used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodian: Preparing activity: Army - IH Army - IH Navy - NU Review activities: (Project No. 8455-2010-035) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-