ARMY MIL-DTL-3628 44 F-2009 BADGE QUALIFICATION ANNUAL RIFLE SQUAD COMBAT PRACTICE COMPETITION MARINE CORPS《海军陆战队步枪班年度战斗演习比赛资质徽章》.pdf

1、 AMSC N/A Page 1 of 3 FSC 8455 INCH-POUND MIL-DTL-3628/44F 15 August 2009 SUPERSEDING MIL-DTL-3628/44E 15 November 1996 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, ANNUAL RIFLE SQUAD COMBAT PRACTICE COMPETITION, MARINE CORPS This specification is approved for use by all Departments and Agencies

2、 of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. DASH NO.1 -1: Gold -2: Silver -3: Bronze MATERIAL: -1, -2: Red Brass -3: Gilding Metal Provided by IHSNot for ResaleNo reproducti

3、on or networking permitted without license from IHS-,-,-MIL-DTL-3628/44F Page 2 of 3 FINISH: OBVERSE: -1: Gold Plated, Matte Finish, Polished Highlights and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 8. -2: Silver Plated, Lightly Oxidized, Relieved, Polished Highlights and

4、 shall match TIOH Metal Finish Chip Number 15. -3: Lightly Oxidized, Relieved, Polished Highlights. REVERSE: -1: Gold Plated, Mirror-like Polished -2: Silver Plated, Mirror-like Polished -3: Mirror-like Polished DIMENSIONS: HEIGHT (overall): ASSEMBLED: 1-15/16 inches (REF) PENDANT (excluding lugs):

5、1-15/32 inches (REF) SUSPENSION BAR (excluding lugs): 1/4 inch (REF) WIDTH (overall): PENDANT: 1-3/16 inches (REF) SUSPENSION BAR: 1-29/32 inches (REF) THICKNESS (at rim): PENDANT: 0.075 inch + .005 inch SUSPENSION BAR: 0.060 inch + .005 inch NOTES: 1. The term (REF) refers to the measurements taken

6、 from the Government furnished hub or die. 2. The lugs are an integral part of both the pendant and suspension bar. 3. The connecting links shall be formed from 0.042 inch + 0.002 inch diameter wire and shall have an outside diameter of 3/16 inch + 1/64 inch. 4. The attaching device shall be prong a

7、nd clutch type. Nickel plated flat ball clutches shall be used for Dash No. -2 and red brass flat ball clutches shall be used for Dash No. -1 and -3. The prongs shall be located on the horizontal center line of the back of the suspension bar equidistant from each end and 1-7/16 inch + 1/16 inch apar

8、t. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and co

9、ntractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/44F Pag

10、e 3 of 3 Custodian: Army - IH Preparing activity: Navy - MC Army - IH (Project No. 8455-2009-100) Review activities: DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-