ARMY MIL-DTL-53133 C-2002 GENERATOR SETS SKID MOUNTED TACTICAL QUIET DIESEL ENGINE DRIVEN ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS GENERAL SPECIFICATION FOR《一般规格的5至60万千瓦交流电 柴油机驱动.pdf

1、 INCH-POUND MIL-DTL-53133C 15 April 2002 SUPERSEDING MIL-DTL-0053133B(ME) 13 September 1996 And MIL-DTL-0053133A(ME) 24 July 1995 And MIL-G-53133 30 August 1993 DETAIL SPECIFICATION GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS GENERA

2、L SPECIFICATION FOR Inactive for new design after 11 August 1997. This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements for generator sets (hereinafter referred to as “set“ or “sets“

3、), skid mounted, tactical, quiet, alternating current, diesel engine driven, 5 through 60 kilowatts. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Communications-Electronics Command, A

4、TTN: AMSEL-LC-CCS-G-GB, 10115 Gridley Road Suite 201, Fort Belvoir, VA 22060-5849 by using the Standardization Document Improvement Proposal (DD Form 1426) or by letter. AMSC N/A FSC 6115 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleN

5、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 21.2 Classification. The sets will be tactical and of the following modes and sizes: MODE: I - 50/60 Hz II - 400 Hz III - 60 Hz SIZE: 5 - 5 kW, MODE II and III 10 - 10 kW, MODE II and III 15 - 15 kW, MODE I and II (12

6、.5 kW at 50 Hz) 30 - 30 kW, MODE I and II (25 kW at 50 Hz) 60 - 60 kW, MODE I and II (50 kW at 50 Hz) 1.3 Set rating. The set will be rated 0.8 power factor (pf), lagging, and will be re-connectable for the following voltages: - 5/10 kW, 60 Hz and 400 Hz a. 120-volt, single phase, 2 wire b. 120/240-

7、volt, single phase, 3 wire c. 120/208-volt, 3-phase, 4 wire - 15/30/60 kW, 50/60 Hz and 400 Hz a. 120/208-volt, 3-phase, 4 wire b. 240/416-volt, 3-phase, 4 wire 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are needed to meet the requirements specified in sections 3 and 4

8、 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all speci

9、fied requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 32.2.1 Specifications, standards, and handbooks. The

10、 following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto,

11、 cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-52557 - Fuel Oil, Diesel; for Posts, Camps and Stations. A-A-52624 - Antifreeze, Multi Engine Type. DEPARTMENT OF DEFENSE MIL-PRF-2104 - Lubricating Oil, Internal Combustion Engine, Combat/Tactical Service. MIL-PRF-2105 - Lubricating O

12、il, Gear, Multipurpose (Metric). MIL-PRF-5624 - Turbine Fuel, Aviation, Grades JP-4 and JP-5/JP-8 ST. MIL-PRF-10924 - Grease, Automotive and Artillery. MIL-F-46162 - Fuel, Diesel, Referee Grade. MIL-PRF-46167 - Lubricating Oil, Internal Combustion Engine, Arctic. MIL-A-53009 - Additive, Antifreeze E

13、xtender, Liquid Cooling Systems. MIL-DTL-83133 - Turbine Fuel, Aviation, Kerosene Type, Grade JP-8. MIL-L-85762 - Lighting, Aircraft, Interior, Night Vision Imaging System (VIS) Compatible. (See Supplement 1 for list of associated specification sheets). STANDARDS DEPARTMENT OF DEFENSE MIL-STD-209 -

14、Slinging and Tiedown Provisions. MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystem and Equipment. * MIL-STD-462B - Measurement of Electromagnetic Interference Characteristics. MIL-STD-705 - Generator Sets, Engine-Driven, Methods of Tests and Inst

15、ructions. MIL-STD-814 - Requirements for Tiedown, Suspension and Extraction Provisions on Military Materiel for Airdrop. MIL-STD-882 - System Safety. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 4MIL-STD-1472 - Human Engineering. *(

16、U)MIL-STD-2169 - High Altitude Electro-Magnetic Pulse Environment (HAEMP).(u) * MIL-STD-462B, dated 11 January 1993, will be used. * (Application for copies of the above classified standard are available to personnel with the appropriate security clearance from Headquarters US Army Communications-El

17、ectronics Command, Research, Development and Engineering Center, Command/Control and Systems, Integration Directorate - South, ATTN: AMSEL-RD-C2-PD-E, 10108 Gridley Road, Suite 1, Ft Belvoir, VA 22060-5817.) HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-454 - Guidelines for Electronic Equipment. MIL-HDBK

18、-705 - Generator Sets, Electrical, Measurements and Instrumentation. MIL-HDBK-784 - Guidelines - Design to Minimize Contamination to Facilitate Decontamination of Military Vehicles and Other Equipment Interiors and Exteriors. MIL-HDBK-1791 - Designing for Internal Aerial Delivery in Fixed Wing Aircr

19、aft. (Unless otherwise indicated, copies of specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to th

20、e extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of the documents not listed in the issue of the DoDISS are the issues of the docu

21、ments cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ASQC Z 1.4 - Sampling Procedures and Tables for Inspections by Attributes. (Application for copies should be addressed to: American National Standards Institute, 1430 Broadway, New York NY 10018.) Provided by IHS

22、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 5NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) MG-1 - Motors and Generators. (Application for copies should be addressed to the National Electrical Manufacturers Association, 2101 L Street, NW, W

23、ashington DC 20037.) UNDERWRITERS LABORATORIES INC. UL-94 Tests for Flammability of Plastic Materials for Parts in Devices and Appliances. (Applications for copies should be addressed to Underwriters Laboratories Inc., 1285 Walt Whitman Road, Mellville L.I., NY 11747.) 2.4 Order of precedence. In th

24、e event of a conflict between the text of this document and the references cited herein, (except for related associated specifications and specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specifi

25、c exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheet requirements for individual set size, and mode. The individual set requirements shall be as specified herein and in accordance with the applicable specification sheets (see 6.2). In the event of any conflict between the requireme

26、nts of this specification and the specification sheets, the latter shall govern. 3.1.1 Drawings. The drawings forming a part of this specification (as listed in the applicable specification sheets), are end product drawings. No deviation from the prescribed drawing requirements is permissible withou

27、t prior approval of the contracting officer. Where tolerances could cumulatively result in incorrect fits, the contractor shall provide tolerances within those prescribed on the drawings to ensure correct fit, assembly, and operation of the set. Any data (e.g. shop drawings, layouts, flow sheets, pr

28、ocessing procedures, etc.) prepared by the contractor or obtained from a vendor to support fabrication and manufacture of the production item shall be made available, upon request, for inspection by the contracting officer or the designated representative. 3.1.2 Size and weight. Set size and operati

29、onal weight (see 6.4.15) shall be as specified in the applicable specification sheets. 3.1.3 Reliability. Set reliability shall be as specified in the applicable specification sheets. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 63.

30、2 First article (preproduction model). When specified (see 6.2), one generator with excitation system and five complete assembled sets of each size and mode shall be furnished for examination and testing within the time frame specified (see 6.2) to prove prior to starting production that the contrac

31、tor is capable of producing sets that comply with the requirements of this specification. Examination and tests shall be as specified in section 4; and, unless otherwise specified (see 6.2), all examination and tests shall be conducted by the contractor subject to surveillance and approval by the Go

32、vernment. 3.3 First article (production model). When specified (see 6.2) five or more sets per size, per mode, shall be furnished for inspection as specified in section 4. Unless otherwise specified (see 6.2), all examinations and tests shall be conducted by the contractor subject to surveillance an

33、d approval by the Government. 3.4 Materials. Sets shall be fabricated from compatible metals and materials that are inherently corrosion resistant or are treated to prevent the various forms of corrosion and deterioration that may be encountered in the storage and operating environments specified he

34、rein. Dissimilar metals shall not be used in intimate contact with each other unless protected against galvanic corrosion. Use of polyvinylchloride (PVC) is prohibited except as specified herein. Materials selected shall be free from perceptible odors and noxious fumes; fire retardant conforming to

35、UL-94 HF-1; and unaffected by battery electrolyte or petroleum (fuels, lubricants and coolants) products specified herein. All rubber compositions shall be resistant to ozone deterioration and shall be formulated with an antiozonant system. 3.5 Design. (See 3.1). 3.5.1 Engine. The engine, including

36、all systems and components, shall comply with applicable Environmental Protection Agency (EPA) regulations and meet the requirements as specified herein. 3.5.1.1 Oil temperature. Oil temperature in the oil sump shall stabilize between 100 and 265 F under all operating conditions specified herein. 3.

37、5.1.2 Smoke limits. The set engine shall operate under all conditions specified herein at all set loads up to and including rated load, with a smoke reading of not more than 4.0 when measured and analyzed as specified in 4.7.2.21. Overload and transient conditions are excluded. 3.5.2 Cranking system

38、. The cranking system shall be 24 volts direct current (DC), negative ground. The set shall not be damaged (see 6.4.3) in the event polarity of the battery cables is reversed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 73.5.3 Batt

39、eries. Batteries shall be furnished with electrolyte, in all first article sets. When specified (see 6.2), batteries with shall be furnished with all production sets. The batteries shall have sufficient capacity to permit fulfillment of the following requirement under all conditions between 120 and

40、-25 F ambient temperatures: After two consecutive cranking cycles, each compromising 15 seconds of continuous cranking, on an inactive set (engine shut-off solenoid de-energized), followed by a 5-second rest period. 3.5.4 Starting aid. Ether tanks shall be furnished in the first article sets. Produc

41、tion sets shall be furnished without ether tanks. 3.5.5 Governing system. The governing system shall provide the frequency performance as specified in the applicable specification sheets. Any loss of input signal to the governing system shall not cause the set to operate at more than 115 percent of

42、the rated speed. 3.5.6 Generator and excitation system. The generator and excitation system (exciter, voltage regulator, and other accessories necessary to control the output voltage) shall meet the requirements as specified herein and on the applicable specification sheets. 3.5.7 Generator. No dama

43、ge (see 6.4.3) shall result from running the set at its low idle speed (see 6.4.18) setting for a period of one hour with the excitation system energized and the generator set temperature stabilized in an ambient of 49 C (120 F). Phase sequence shall be ABC and L1 to L2 and L3. The generator shall b

44、e in electrical and mechanical balance at all speeds up to 125 percent rated speed. The generator shall withstand operation at 125 percent rated speed to be 2250 rpm for 60 Hz and 2500 rpm for 400 Hz. 3.5.8 Temperature rise. When the generator and auxiliary items are installed in the set, allowable

45、temperature rise of generator coils, windings and mechanical parts, shall not exceed the following: Coils, windings and connections: - 105 C (189 F) (measured by rise in resistance method) Generator bearings: - 50 C (90 F) Poles, cores, and other mechanical devices: Provided by IHSNot for ResaleNo r

46、eproduction or networking permitted without license from IHS-,-,-MIL-DTL-53133C 8- Same as for the parts in contact with insulation in which the parts are in contact. 3.5.9 Insulation resistance. Insulation resistance of generator windings shall not be less than 1 megohm in an ambient temperature of

47、 25 C (77 F). 3.5.10 Dielectric strength. Generator windings shall withstand the following 60 Hz voltages applied for 1 minute: a. Generator field and exciter windings - 10 times ceiling voltage, but neither less than 1,500 nor more than 3,500 volts (applied between windings and ground); b. Windings

48、 energized by the 24-volt DC control, cranking and battery charging systems - 500 volts (applied between windings and ground); c. Generator stator windings - 1,832 volts between phase windings and 1,480 volts between phase windings and ground; d. All others - twice rated voltage plus 1,000 volts (ap

49、plied between winding and ground and between windings where applicable). 3.5.11 Short circuit. The generator, voltage regulator and excitation system operating as a unit shall withstand two consecutive single-phase line-to-line, single-phase line-to-neutral, and symmetrical 3-phase short-circuits at 5-minute intervals at generator output terminals when operating at rated load (see 6.4.6) and frequency without reduction in dielectric str