ARMY MIL-F-10071 A-1952 FLAME THROWER COMBAT VEHICLE MAIN ARMAMENT M5-4《M5-4主战装备 战车喷火器》.pdf

1、MUITARY SPECIFICATION 22 October 1952 SUPEHSDING MIL-F-10071 (CdC) - 28 December 1949 FLAME THROW, COMBAT VEHICLE, MAIN ARMAMENT, M5-4 1, SCOPE 1.1 This specification covers one type of main armament combat vehicle flame thrower , 2, APPLICABU SPECIFICATIONS, STANDARDS, DRAWINGS, AND PUBLICATIONS 2.

2、1 The following specifications, standards, and drawings, of the isaue in effect on date of Invitation for bids, form a part of this specification: SPECIFICATIONS FED- W- Aircraft Reciprocating Engine. - Surface Roughness, Vadness, and Lay. - Marking of Shipments, - Flame Thrower, Combat Vehicle, Mai

3、n Armament, I45-4 - Bill of Material, Sheet 1 of 2 Sheets, - Flame Thrower, Comat Vehicle, Main Armament, $5-4,- Bill of Material, Sheet 2 of 2 Sheets, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(Copies of specifications, standards, and drawings

4、 required by the con- tractors in connection with specific procurement functions shocd be ob- tained from the procuring agency or as directed by the contracting officer,) 3. REQUJIREMENTS 3.2 Material,- All materials used in the manufacture and assem5ly of tho flame thrower shall eqnforn to the spec

5、ifications and drawings forming a part of this specification, 3.2 Manufacture and assembly,- The flame thrower shall be manufactured Surface roughness, waviness, and lay specified and assembled as specified on the subsidiary drawings listed on Drawings 681-1-3009 and C8l.-l-3?%. by symbols on detail

6、 drawings shall comply with the applicable classes specified in Standard MUISTD-10, yards measured from the end of the nooitle to the center of ground deposit when tested as specified in 4,rCe 3,3 Range,- The flame thrower shall project a flame for a distance of 95 3.4 Workmanship.- All work shall b

7、e done in a neat and workmanlike manner. 4, 4.1 Lot.- A lot shall consist of the flame throwers produced by one manu- facturer, from the same materials, and under essentially the same inanufactur- ing conditions. The inspection lot for nondestructive inspection, within the above limitations, shall b

8、e designated by the inspector. SAMPLING, INSPECTION, AND TEST PROCEDURES 4*2 Sampling for nondestructive inspection.- Each flame thrower shall be inspected as specified in 4,3 and tested as specified in 4.4 (See 6.2). 4,3 Inspection. 4.3.1 Components.- The inspector shall ascertain that ali material

9、s, com- ponents, or subassemblies of the flame thrower covered by separate drawings, specifications, or standards are in accordance with the applicable drawings, specifications, or standards prior to final acceptance of the flame thrower. 4.3.2 -Flame thrower.- The inspector shall inspect the flame

10、thrower for compliance with this specification. 4.3.3 packaging, packing, and marking of the flame thrower for compliance with section 5, 4.4 Range test.- The flame thrower shall be fired using the 1/2 inch nozzle exbension and a motor fuel conforming with Specification W-M-561 containing 4 percent

11、to 1Cl percent Napalm thickener conforming to Specifi- cation JAN-N-589 in the min fuel system and using motor fuel conforming Packaging, packing, and marking.- The inspector shall inspect the Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-to Specif

12、ication W-M=561 or aviation gasoline conforming to Specification MTLF-5572 in the secondary fuel system and the atomizer fuel system, 5. PREPARATION FOR DELIVERY 5.1 Packaging and packing, 5.1.1 Containers FH-1 and FH-2,- FH-1 and FH-2 containers shall be packaged and packed for shipment to assernbl

13、y plants as specified on Drawing D81-2-23? which is listed on Drawing C81-1-3009, 5.1.2 Rotor and counterweight.- The rotor and counterweight shall be packaged and packed for shipment to assembly plants as specified on Drawing Del-2-211 which is listed on Drawing C81-1-3009, 5.1.3 Miscellaneous part

14、s.- The miscellaneous parts shall be packaged and packed for shipment to assembly plants as specified on Drawing D81-2-259 which is listed on Drawing CSl-1-3009, !5.1*4 Gun and turret basket.- The gun and turret basket shall be pack- aged and packed for shipment to assembly plants as specified on Dr

15、awing D81-2-195 which is listed on Drawing C81-1-3009, 5.2 Marking,- In addition to any special marking required by the con- tract or order, all shipping containers shall be marked in accordance with Standard MIL-STD-129. 6. NOTES 6.1 Ordering data.- Procurement documents should specify the title, n

16、umber, and date of this specification. 6.2 Sampling and testing,- hken the contractor consistently produces high quality material and operates under a system of quality control acceptable to the Government, the Government, at its discretion, may modify, in whole or in part, the sampling and testing

17、procedures specified herein. Government reserves the right to return at any time, without previous notice to the contractor, to the sampling and testing procedures specified in this specification. However, the 6.3 Stock number.- The Chemical Corps stock number for this item is and the fact that the

18、Government may have formulated, furnished, or in any way supplied the said drawings, spec- ifications, or other data is not to be regarded by implication or otherwise as in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or.sel1 .* any patented invention tbt may in any way be related $hereto. - 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-