ARMY MIL-F-44397-1990 FRAME TENT (SICPS)《帐篷架(SICPS)》.pdf

1、I INCH-POUND 1 MIL-F-44397 (GL) 10 January 1990 MILITARY SPECIFICATION FRAME, TENT (SICPS) This specification is approved for use by the Natick Research, Developnent and Engineering Center, Department of the Amy, and is available for use by all Departments and Agencies of the Department of Defense.

2、1. SCOPE 1.1 Scope. 2. APPLICABLE iXEUMENTS This specification covers a frame for a cannand post tent. 2.1 Goverrment documents. 2.1.1 Specification, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless o

3、therwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplenent thereto, cited in the solicitation (see 6.2). SPECIFICATIONS , FEDERAL DDD-L-20 - Label: For Clothing, Equipage, and Tentage, (Ge

4、neral Use) PPP-E601 - Boxes, Wood. Cleated-Plywood PPP-B-640 - Boxes, Fiberboard, Corrugated, TripleWall Beneficial comnents (reccxmiendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: and mineering Center, Natick, MA 01760-5

5、014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. U.S. Army Natick Research, Developnent, AMSC N/A FSC 8340 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. e Provided by I

6、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILF44397 (GL) t I MILITARY MIL-T-704 - Treatment and Painting of Material MIL-C-5541 - Chemical Conversion Coatings on Aluminum and Alminum Alloys MILITARY MIL-SPD-105 - Scrmpling Procedures and Tables for Inspecti

7、on by MIL-ST5129 - Marking for Shipnent and Storage MIL-STD-130 - Identification Marking of U.S. Military Proprty (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available fran the Naval Publications and Forms Center, (Am: NPODC) , 5801 Tabor A

8、venue, Philadelphia, PA 19120-!5099.) Attributes 2,1.2 Other Govemnent documents, drawings, and publications. The following other: Government documents, drawings, and publications form a mrt of this document: to the extent specified herein. Unless otherwise o on the drawings and 3.2.1. m.e frame can

9、ponents shall be coated as specified The finish coating shall be continuous and uniform, e.g., free of sag, run, pinhole, blister, wrinkle, area of thin or no film, 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-44397 (GL) scratch or scruff,

10、 foreign mtter imbedded in finish, and wet or tack! Areas of finish damaged during flexing of movable joints shall be touc paint . led up. 3.4.2.1 Elastic cord. The elastic cord on Drawings 5-4-6946, 5-4-6947, and 5-4-6967 shall be crimp incorrect; illegible; of improper size, anti interior) locatio

11、n, sequence, or niethod of application Materials Any ccmponent missing, damaged or not as specif ie Workinanship Con tent 5. PACKAGING Inadequate application of components, such as: incanplete sealing or closure of flap, improper taping, loose strapping or inadequate stapling Bulged or distorted con

12、tainer Number per container is more or less than required 5.l. Preservation. Preservation shall be level A or Comnercial as specified (see 6.2). 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-t 7 MIL-F-44377 43 9777706 0208211 6 MIL-F-44397 (GL) 5

13、.1.1 Level A preservation. The frame shall be completely folded, and secured with the binding strap provided. be wrapped or cushioned to prevent damage to the finish. of each purlin and header shall be wrapped. tape and wrapped or cushioned to prevent damage to the finish. The ends of the folded ass

14、embly shall All pins shall be secured with The end connections 5.1.2 Corrimercial preservation. Components of each frame shall be preserved in accordance with ASTM D 3951. 5.2 Packing. Packing shall be level A, B or Consnercial as specified (see 6.2). 5.2.1 Level A packing. One complete frame, prese

15、rved as specified in 5.1, shall be packed in a close fitting shipping container conforming to overseas type, style A, type 3 load of PPP-B-601. Inside dimensions of the box shall approximate 70 inches in length, 20 inches in width, and 13 inches in depth. Each box shall be provided with skids fabric

16、ated in accordance with the requirements of the box specification. to prevent movement or damage during shipment. reinforced with strapping in accordance with the appendix of PPP-B-601. shall be packed as specified in 5.2.1, except that the box shall conform to class 2, style A, NO. 1 or 2 end of PP

17、P-B-640. Cushioning shall be used, as necessary, Each box shall be closed and 5.2.2 Level B packing. One caplete frame, preserved as specified in 5.1, 5.2.3 Cmrcial packing. Frame sections or individual components when procured separately, preserved as specified in 5.1, shall be packed in accordance

18、 with ASTM D 3951. 5.3 Marking. In addition to any special marking required by the contract or purchase order, shipnent shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, bu

19、t is not mandatory.) 6.1 Intended use. The frame shall provide support for a tent 11 feet long, 11 feet wide and 9-1/2 feet high. post tent. The tent is designed for use as a cornnand 6.2 Acquisition requirements. Acquisition documents must specify the following: a. b. c. d. Levels of preservation a

20、nd packing (see 5.1 and 5.2). Title, number, and date of this specification. Issue of DODISS to be cited in the solicitation, and if required, the When a first article is required (see 3.1, 4.3, and 6.3). specific issue of individual documents referenced (see 2.1.1 and 2.2 9 Provided by IHSNot for R

21、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-qY347 3 977990b 0208232 9 MIGF-44397 (GL) 6.3 First article, When a first article is required, it shall be inspected aM approved under the appropriate provisions of Fm 52.209. The first article should be a preproduction

22、sample, appropriate type of first article and the number of units to be furnished, The contracting officer should also include specific instructions in acquisition doemnts regarding arrangements for selection, inspection, and approval of the first article. “he contracting officer should specify the 6.4 Subject term (key word) listing. Brace Shelter Structure Support: Tent: Cus tdi an: Amy - GL Preparing activity: Amiy - GL (Project 8340-A532) 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-