ARMY MIL-F-51163 A (1)-1987 FILTER UNIT GAS-PARTICULATE GED OR EMD 300 CFM ABCA-M6A1《GED或EMD 300 CFM ABCA-M6A1毒气微粒过滤器机组》.pdf

1、 e2 -. MIL-F-SLLb3A (1) 42 7777706 0234568 L W MIL-F-51163A( EA) AMENDMENT 1 12 June 1987 MILITARY SPECIFICATION FILTER UNIT, GAS-PARTICULATE, GED OR EMD, 300 CFM, ABCA-M6Al This amendment forms a part of MIL-F-51163A(EA), dated 17 December 1981, and is approved for use within the Chemical Research,

2、 Development and Engineering Center, Department of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 Preamble, lines 1 and 2: Delete “US Army Armament Research and Development Command“ and substitute “U.S. Army Chemical Research, Development and E

3、ngineer- ing Center“. . Beneficial comments block lines 3 and 4: Delete “Commander, US Army Armament Research and Development Command, ATTN: 4D and Engineering Center, AT“; SMCCR-SPT-S, Aberdeen Proving Ground, MD 21010- 5423“. DRDAR-TSC-S, Aberdeen Proving Ground, 21010“ and substitute “Commander,

4、U.S. Army Chemical Research, Development PAGE 2 Military. standards: Add “MIL-STD-1188 - Commercial Packaging of Supplies and Equipment .I1 2.1.2: Line 4: Delete US Army Armament Research and Development Command“ and substitute “U.S. Army Chemical Research, Development and Engineering Center“. Line

5、5 : Delete “CHEMICAL SYSTEMS LABORATORY“. _. AMSC N/A Page 1 of 3 FSC 4240 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F- 5ii63A( EA) AMENDMENT 1 2.2: Add the f

6、ollowing: “AMERICAN PLYWOOD ASSOCIATION ( APA) U.S. Product Standard PS 1 - Construction and Industrial Plywood (Application for copies of APA publications should be addressed to the American Plywood Association, P.O. Box 11700, Tacoma, WA 984ii.)11 PAGE 3 Lines 1 to 8: Delete these lines in their e

7、ntirety from “NATIONAL MOTOR FREIGHT . . .“ to “. . . Chicago, IL 60606.) PAGE 4 k.2.3 : Line 4: Below line 13: Add i(a)lf before “Filter Unit“. Add item (b)“ as follows: I( b) Packaging inspection (section 5) Major: AQL 2.5 percent defective 101 Cleaning , drying and preservation incorrect (5.1) 10

8、2 103 Packing incorrect ( 5.2) i04 105 Unit packing incorrect ( 5 . 1.2) Shipping container and const-ction, closure and strapping incorrect (5.2.1, 5.2.2, and 5.2.3) Marking illegible or incorrect ( 5.3 ) .If PAGE 5 5.1.1.1, line 5: Delete the last sentence in its entirety and substitute with “Pres

9、ervatives specified herein, identified by “P“, and their application, shall conform to the applicable specifications listed in and the application criteria cited in 1p-116 .“ .- PAGE 6 5.1.1.4, line 4: Delete the last sentence in its entirety. 5.1.2: Delete “Packaging.“ and substitute “Unit packing.

10、“ 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-51163A( EA) AMENDMENT 1 5.1.2.1, line 6: Delete “group A, NN-P-530 (type 1, grade 3 or 4 of CS 35).“ and substitute “structural I, grade A-C of US Product Standard PS-1.“ 5.1.2.5: Lines 2 and

11、3: MIL-P-. Each item“. Delete “shall be packaged in accordance with Method Line 6: Add “or c“ between “V3c“ and “fiberboard“. PAGE 7 5.l.2.lO: Delete in its entirety and substitute the following: “5.l.2.lO Technical publications. When technical publications are fied in the contract or order, or prov

12、ided to the prime contractor as G III of cpeci- vern- ment furnished equipment, the publications shall be packaged in accordance with method IC-1 of MIL-P- . “ PAGE 9 I . 5.2.2.1: DeLete in its entirety and substitute the following: 115.2.2.1 rn e 1 and type 11 filter units. Each filter unit and the

13、ir respective components, unit packed as specified in 5.1.2.1 through 5.1.2.10, shall be packed in accordance with MIL-STD-1188.“ 5.3: Delete in its entirety and substitute the following: “5.3 Marking. or order, unit packs (5.1.2) and level A packs (5.2.1). shall be marked in accor- dance with ML-ST

14、D-129. in MIL-STD-1188. units, and or gas filters installed therein, shall be marked on shipping con- tainers (5.2.1 and 5.2.2) and shall be in accordance with the requirements of MIL-STD-129.! In addition to any special marking required by the contract Commercial packs (5.2.2) shall be marked as specified When specified (see 6.21, lot control markings of filter Preparing activity: Army - EA (Project No. 424O-Ag17) . 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-