ARMY MIL-G-20587 E-1973 GLOVES WIRE MESH ENTIRE HAND《全网线手套》.pdf

1、.-. MIL-G-20587E 4 7777706 OLt58276 7 E M1L-20587E 16 January 1973 SUPERSEDING MIL-G-20587D 16 November 1967 MILITARY SPECIFICATION GLOVES, RIRE MESH, ENTIRE HAND This specification is approved for use by all Departments and Agencies of the Department of Defenae, 10 SCOPE 1 o 1 Scope. Thia specifica

2、tion covere .protective7wfre mesh gloves which cover the entire hand, 1.2 Claesffieation. The wire mesh glove covered by thfe specification ahail be of the following sizes and hands as specified (oee 6.2): Size - Small Size - Medium Size - Large Right hand Left hand 2, APPLICABLE DOCUMENTS 2.1 The f

3、ollowing docments, of ehe issue in effect on date of invita- tion for bids or request for proposal, form a part of this speciffcation to the extent specified herein: SPECIFICATIONS V-T-276 - Thread, Coton QQ-W-321 - Wire, Copper Alloy PPP-B-636 - Boxes, Shipping, Ffberbard MILITARY MIL-8-13282 - Sil

4、ver and Silrer Alloy MIL-F-21840 - Fastemer Tape, Hook and Pile, Nylon PSC 8415 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS PED- FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tableer for In

5、spection by MIL-STD-129 - Marking for Shipment and Storage At tributes DRAWING ARMY NATICK LABORATORIES 5-11-79 3 - Glove, Wire Mesh, Entire Hand; Illustratin and Details (Miniature copy of Drawing 5-11-793, identified as figure 1, is attached for information purpoeerr only,) (Copies of specificatio

6、ns, standards and drawings required by suppliers in connection with specific procurement functionsshould be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publicatione,. The following documents form a part of this opecification to the extent specified here

7、in. Unless a specific issue is identified, the feeua in effect on date of invitation for bids or request for proposal ehall apply : Na.spacified herefa. Except as otherwise apecffied in the contract or order, the supplier *y tise. his own, or any other fscilitfes unlees disapproved by the Governqent

8、 ,The Government reserves the right to perfom*any.of the inspections set forth in the speci- ffcatfon where sueh inspections are deemed neceesary to assure supplies and services esnfom to premxibed requirements, 4,2 Claasfficaton of inspection, The inspection requirements specified herein are efassf

9、ffed eps-follmx. . 1, 2, 3, Inepeetion of preparation for delivery (see 4,4*3). First amptide inspection (see 4.3), Quality conformance inspection (see 4 4) e 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-G-20587E 84 E 999990b OLi58300 5 m

10、MI42038 7E 4.3 First atfle When a first article is required, the wire mmh The gloves srhall be as specified in gable I and dimensions specified. preaence of any defect QP of any dimension not within specified require- menta half be cause for rjeetioa of first articae, 4.4 Quality coafomnce fnspeetfo

11、n, Except as otherwise specified herein, saniplimg for inspection shall be performed in accordance with the provisions se8 fortta in MIL-STD-105, 4,4,l Component and materid inspection, In accordance wPth 401 above, components and materiale shall be inspected and tested in accordance wth all d P def

12、ect, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-20587E TABLE I, Classification of defects (contd) Class if ica t ion Examine Defect Major Minor ,. Design Any characteristic not in accord- ance with speciffed requirements Conetruction and A

13、ny component missing workmanship Any component misplaced Any component or assembly malformed Wire Mesh Any ring in the wire mesh glove not engaging four other rings, except in the seam area Any of the connecting rings in the seam area not joined One open ring Two or more open rings fneertfons of the

14、 wre mesh into the wrist strap not accomplished as specfie Stitch fng Not type speciffed (mis t strap) Any POW of stitching missing Any open seam P/4 inch or more Any open seam lese than 1/4 inch he stitch per inch less than the mnfmum specified More than one stitch per inch lese than the minimum sp

15、ecified More stitches per inch than maximum specified damaging webbing Mora et%tches per inch than maximum opecifed but not damaging webbing Loose stitch tetraion resuiting in a loosely secured eh %read ends not trimmed throughout Webbing Any hole, cut, or frayed edge Needle chews less than 1/8 inch

16、 Needle chews more than 1/8 inch Hook tape cruhed, affecting closure Fastener tape x X X X X X X X X X X X X X X X X X X Marking Miseing, incomplete, incorrect, not legible, mot specified size, not in proper location or not X eaccompl%rEehed as epecif fed 6 Provided by IHSNot for ResaleNo reproducti

17、on or networking permitted without license from IHS-,-,-1 P flIL-G-20587E 4 I 777770b 0458302 7 a MIL-0-20587E 4,4,2,2 Dimensional examination, The wire mesh gloves shall be examined for compliance w5th dimensions specified, An9 dimension not within thia epecification tolerance shall be a defect. S-

18、3 with an AQL of 400 defects expressed in tem of defects per hundred anitlso The inspection level shall be 4,4,3 Inspection of preparation for delivery, An inspection shall be . made to detemine that packaging, packing, and-marking comply with the requfremente of section 5 of this specification. ind

19、icated i table II, The lot shall be the number offered for inspection at one time, container fully prepared for delivery. with an AQL of 4, expressed in terms of defects per hundred units. Defects shall be as shipping containers all beone shipping The sample unit The inspection level shall be 5-2 TA

20、BLE II. Examination of preparation for delivery Examina Defect Markings Missing; incorrect ; illegible; of improper eize, location, sequence OP method of application. Materials Contents Component missing, damaned. or otheruse defective. Contents per container-more or less than specified. 4.4,3,1 Exa

21、mination of shipping containers. When shipping containers are required to be in accordance with PPP-B-636, exarkination for defects in closure, waterproofing, and strapping shall be in accordance with PPP-B-636. 5, PREPARATION POR DELIVERY I 5,l Packaging. Packaging shall be level A or C as specifie

22、d (see 6.2). 5,l,f Level A, Each glove shall be placed fn B nomfnal .0025-inch thick polyethylene bag, P left-hand gloves of one eize only rhafl then .be packaged in a nominal ,0025- inch thick polyethylene bag, 5,1,2 mo Gloves shall be packaged to afford adequate protec- tion against damage during

23、shipment from the supply source to the first receiving aetiv3tyo this raquranent: o The bag ehall be closed and secured. Six bagged right-hand The bag shall be closed and secured, The supplier may we his etandard practice when it meets 5,2 Paelring, Packing ahall be level A, B, or C ata specified (s

24、ee 6.2), Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-20587E 5,2,1 Level A, Fifty rigRt-hand or fifty left-hand gloves of one size Each shipping container only, packaged as specified in 50P, shall be packed in a shipping container conforming

25、 to etyfe RSC, grade V3s of PPP-B-636, shall be dosed, waterproofed by means of tape, and reinforced with flat strapping or tape banding in accordance wfth PPP-B-636, 5,2,2 Level Be Fifty right-hand or fifty left-hand groves of bne site only, packaged as epco&tied in 0j01, shall be packed in a shipp

26、ing container conforming to style RSC, type CF, varfety SW, ur type SF, class domestic, grade 200 of PPP-B-636, dance with method II of the appenix si PPP-B-636, Each shipping container shall be closed in accor- 5,2,2,1 When epeeffied (sea 6,2), the shfpping*container shall be VC, Gloves, packaged a

27、s specified in 5.1, shall be . VS, OP VS, fabricated and closed in accordance with PPP-B-636. 5,2,3 Level Co packed in a manner to insure carrier acceptance and safe delivery at desttnation at the lowest transportation rage for euch euppliee . Contanera shall be in accordance with Uniforai Freight C

28、lassiPication Rules Qr National Motor Freight Classification Rules, as applicable. 5,3 Markfnq, Ia addition to any special marking required by the contract OF order, iimterfr packages and shipping containers shall be marked in accordance with MIL-STD-129, &- 60 NOTES 6,l Intended use, The gloves cov

29、ered by this ,specification are intended to protect the hand in meat-cutting operations, worn over a white cotton glove insert. following: The glove fa 6,2 Ozdering data, Procurement documents should specify the (a) Title, number and date of this specification . (b) (cl (d) (e) Size of glove faqgire

30、d and whether for right or left hand When a first article is required (see 3oP, 4,3, and 6,3) Selection of the appffeabfe level of pachagfng and packng When weeither-resPtant grade f fbarboard shipping containers (see loa) (esee 501 and 5,2) are required for Pew1 B paekimg (see 5,2,2,f) dnspeeted an

31、d approved under the appropriate provisions of ASPR 7-104 o 55 o The first article. should be a preproduction sample, initial production Stem or other apeeifie item described under $he definition of a first 6,3 Fret article, When do first article is required, it shall be a Provided by IHSNot for Res

32、aleNo reproduction or networking permitted without license from IHS-,-,-=F MIL-G-20583E 84 I 777770b ClLi58304 2 I -1 Ma-G-20587E artisla fa the ASPR, type of fitst article and the number of unitsito be furnished, The contracting offfcer should include speicefffc fnstmctfonk in all procurement instr

33、uments re- garding arrangemente for hspectfsn and approval of the ESrst article. 6,4 Asteri&e are not wed in th%e revision to identify changea with respect to the previous issue9 due to the extensiveness of the changes. The contracting officer sRcuPd rapecffy the appropriate Cus todianir : Preparing

34、 activity: Apm9p-eL APmy-m Air Force - 82 Ansjv-MD Ar Force - 45 Project NO o 8415-0659 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 L I I I l I l 1 10 * U. S. GOVERNMENT PRINTING OFFICE: 1973 -714-542/3614 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-