ARMY MIL-G-63444 A-1983 GRENADE GENERAL PURPOSE M73《M73型一般用途的手榴弹》.pdf

1、i, - - MIL-G-6344 4A (AR) 22 August 1983 SUPERSEDING MIL-G-63444 (AR) 2 August 1982 MILITARY SPECIFICATION . GRENADE, GENERAL PURPOSE, M73 This specification is approved for use by the U.S. Army Armament, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the

2、 Department of Defense. 1. SCOPE lit “This specification covers the quality assurance . provisions and speciax requirements not covered by the drawings for parts and assembly of the M73 General Purpose H.E. Grenade 2. APPLICABLE DOCUMENTS 2.3. Government documents. 2.1.1. Specifications and standard

3、s. Unless otherwise specified (see 6-21, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent specif i ed herein. SPECIFI

4、CATIONS MILITARY MIL-A-48078 Ammunition, Standard Quality Assurance Provisions, General Specification for MIL -F-63 4 4 6 Fuzes, General Purpose Grenade: M230 and M231 (Practice) Grenade: M73 * MIL -B - 6 4 O 4 3 Loaded Body Assembly, General Purpose - * STANDARDS MILITARY c MIL-STD- 10 5 Sampling P

5、rocedures and Tables for MIL-STD-1167 Ammunition Data Card Inspection by Attributes f FSC 1330 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander. US Arm Armament Research and Development

6、 Center, Attn. DRSMC-QA, Dover, New ?key 07 by using the seif-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-b3LlLlLlA 2

7、3 m 9797906 0350603 7 * 4 MIL-G- 63 4 4 4A (AR) * 2.1.2 Other Government documents, drawinqs and publications. The following other Government documents, drawings and publications form a part of this specification to the extent speciEied herein. DRAWINGS US ARLUIY ARMAMENT RESEARCH AND DEVELOPMENT CO

8、MMAND (ARRADCOM) PRODUCT AND PACKAGE DRAWINGS 9334143 Grenade, General Purpose, High Explosive, M7 3 (Copies of specifications, standards, handbooks, drawings, and publica.tions required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activi

9、ty or as directed by the contracting officer.) 2.1.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. * 3. REQUIREMENTS 3.1 Materials. Materials shall be in accordance with 3.

10、2 Components and assemblies. The components and assemblies a applicable drawings and specifications. shall comply with all requirements specified on Drawing 9334143 and associated drawings and with all requirements specified in applicable specifications and standards. 3.3 M230 fuze. The fuze shall c

11、omply with specification MIL-F-63446. 3.4 Loaded Body assembly, M73. The loaded body assembly shall comply with specification MIL-B-64043. 3.5 Data requirements. The contractor shall generate data in accordance with the requirements of the data item descriptions - cited in 4.5.2. 3.6 First article i

12、nspection. This specification makes provisions for first article inspection. Requirements for submission of first article samples by the contractor shall be as specified in the contract. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-G-6344

13、4A 13 9779706 0350b04 O MIL-G-63444A (AR) 3.7 WorkmanshiE. Unless otherwise specified on the drawing, all parts and assemblies shall be free from burrs, chips, sharp edges, cracks, unblended radii, surface defects, dirt, grease, rust, porosity, warpage, burn marks, checks, blisters, excess flash, co

14、rrosion products and other foreign matter. The cleaning method used shall not be injurious to any part nor shall the parts be contaminated by the cleaning agents. Surface coating shall be continuous except for a few slight scratches not exposing base material. The loading and assembly operations sha

15、ll be performed in a thorough, workmanlike manner consibtent with the best practices of the industry. All required markings shall be neat and sharply defined. * 4.- QUALITY ASSURANCE PROVISIONS 4.1 Responsibilities for inspections. Unless otherwise mecified in the contract. the contractor is respons

16、ible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the Contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the government. The g

17、overnment reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. herein or in the contract, the provisions of MIL-A-48078 shall apply and are made a part of th

18、is specification. 4.2 - Classification o inspections. Unless,otherwise specified herein, or in the contract, the following types of inspection shall be conducted on this item. Unless otherwise specified a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection. * 4.3

19、.1 Submission. The contractor shall submit a first article sample as designated by the contracting officer for evaluation in accordance with the provisions of 4.3.2. The first article sample shall consist of the following items in sample quantities as indicated: 3 Provided by IHSNot for ResaleNo rep

20、roduction or networking permitted without license from IHS-,-,- - _i_ I_I_ - - MIL-G-63444A 13 9999906 0350605 2 a MIL-G-63444A (AR) Part Description Drawinq Fuze Pushout Assembly See Note Grenade, General Purpose, High Explosive: M73 9334143 Quantity 15 25 Note: Empty M73 body assembly with cap rem

21、oved and empty M230 fuze body. 4.3.2 Inspections to be performed. See MIL-A-48078 and Table I specified herein. 4.3.3 Rejection. See MIL-A-48078. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-G-63LI9VA 13 7777706 03C0606 4 .- . rn s ee al m O

22、 pi , Vol II, AMSDL. Copies of data item descriptions required by the contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the contracting officer.) 6.5 First article. When a first article is required for 6.6

23、Source control and specification control drawings. inspection and approval, see 3.6 and 4.3. Certificates of conformance from the supplier certifying that the item complies with the drawing requirements shall be provided to the government representative. 9 Provided by IHSNot for ResaleNo reproductio

24、n or networking permitted without license from IHS-,-,-._- _ MIL-G-63qLlqA 13 777770b 0350611 B W P MIL-G-63444A (AR) 6.7 Chanqes from previous issue. The margins of this specification are marked with asterisks or vertical lines to indicate where changes (additions, modifications, corrections, delet

25、ions) from the previous issue were made. This was dane as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and Contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Pr epar ing activity : (Project 133WA186) Army-AR Army-AR 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-