ARMY MIL-H-52213 F-1992 HEATERS HOT OIL《热油暖炉》.pdf

1、flIL-H-522L3F 38 9999906 LLbO4LB 588 H 1 INCH-POUND 1 29 June 1992- SUPERSEDING MIL-H-52213E(ME) 17 September 1986 MILITARY SPECIFICATION HEATERS, HOT OIL This specification is approved for use within the USA Belvoir Research, Development and Engineering Center, Department of the Army, and is availa

2、ble for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers three sizes of automatic hot-oil heaters. The heaters shall be skid mounted or trailer mounted, light fuel oil fired, and electric motor driven. 1.2 Classification. The heaters sha

3、ll be of the following types and sizes, as specified (see 6.2): Type I - Skid-mounted. Size 1 - 1,500,000 Btuh output. Size 2 - 2,100,000 Btuh output. Size 3 - 3,000,000 Btuh output. Type II - Trailer-mounted. Size 2 - 2,100,000 Btuh output. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 So

4、ecifications. standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and

5、 Standards (DoDISS) and supplement thereto, citeqin the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: USA Belvoir Research, Development, and Engineering Center, ATTN: S

6、TRBE-TSE, Fort Belvoir, VA 22060-5606 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 3895 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo repr

7、oduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL W-C-586 W-R-550 TT- P-664 UU-T-81 VV-F-800 PPP-B-60 1 PPP-B-636 PPP-P-40 P P P- T- 6 O MILITARY MI L-C-104 MIL- P- 116 MI L-V-173 MI L- P-5 14 MIL-T-704 MI L-C-7 17 MIL-F-3541 MIL-C-3774 MIL-G-3859 MIL-G-10924 MIL-S

8、-12514 MIL-P-14105 MIL-B-16008 MIL-H-18160 MIL-1-22023 MIL-L-22851 MIL-G-25013 MIL-C-46168 MIL-C-52286 MIL-H-52213F 38 = 9999YOb lLb04L9 414 = - Conduit Outlets Boxes, Bodies, and Entrance Caps, - Rod, Ground (with attachments). - Primer Coating, Synthetic, Rust-Inhibiting, Lacquer- - Tags, Shipping

9、 and Stock. - Fuel Oil , Diesel. - Boxes , Wood, C1 eated-Plywood. - Box, Shipping, Fiberboard. - Packaging and Packing of Hand Tools. - Tape: Packaging, Waterproof. Electrical : Cast Metal . Resi st i ng . - Crate, Wood, Lumber and Plywood Sheathed, Nailed and - Preservation, Methods of. - Varnish,

10、 Moisture- and Fungus-Resistant, (for Treatment - Plates, Identification, Instruction and Marking, Blank. - Treatment and Painting of Materiel. - Castable Mix, Refractory, High-Temperature Hydraul ic- - Fittings, Lubrication. - Crates, Wood; Open 12,000- and 16,000-Pound Capacity. - Grease Guns, Han

11、d-Operated, Lever, Push and Screw Type. - Grease, Automotive and Artillery. - Starters, Motor; Across-the-Line and Reduced Voltage Types, A-C Induction, 3/4 to 100 HP, Manual and Electric. - Paint, Heat-Resisting (for Steel Surfaces). - Brick Insulation, High Temperature, Fire Clay. - Hose Assemblie

12、s, Corrugated Steel, 200 Psi and 425 Deg. F Maximum Steam Service Rating. - Insulation Felt, Thermal and Sound Absorbing Felt, Fi brous G1 ass , F1 exi bl e. - Lubricating Oil , Aircraft Piston Engine (Ashless Dispersant) . - Grease, Aircraft, Ball and Roller Bearing. - Coating, Aliphatic Polyuretha

13、ne, Chemical Agent Resistant. - Cable Assemblies, Power, Electrical, (With Molded on Terminations). Bol ted. of Communications, Electronic, and Associated Equipment). Setting. MIL-C-52286/11 MIL-C-52286/24 - Cab1 e Assembly, Power Electrical , Adapter. MIL-C-53039 MIL-V-62038 MIL-T-83133 - Cable Ass

14、embiy, Power Electrical. - Coating, Aliphatic Polyurethane., Single Component, - Vehicle, Wheeled, Preparation for Shipment and Storage - Turbine Fuel, Aviation, Kerosene Type, Grade JP-8. Chemical Agent Resistant. of. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

15、cense from IHS-,-,- flIL-H-52213F 38 W 9999906 LLb0420 136 MIL-H-52213F(ME) STANDARDS FEDERAL FED-STD-H28 FED-STD-595 MI L I TARY MIL-STD-105 MIL-STD-129 MIL-STD-130 MIL-STD-209 MIL-STD-633 MIL-STD-642 MIL-STD-810 MIL-STD-838 MIL-STD-889 MIL-STD-1186 MIL-STD-1366 MIL-STD-1791 MIL-STD-1472 MIL-STD-14

16、74 MS52127 MS53052 MS75021 HANDBOOKS MI L ITARY MIL-HDBK-113 - Screw Thread Standards for Federal Services. - Colors Used in Government Procurement. - Sampling Procedures and Tables for Inspectioi - Marking for Shipment and Storage. - Identification Marking of US Military Properi - Slinging and Tied

17、own Provisions for Lifting i - Mobile Electric Power Engine Generator Standi - Identification Marking of Combat, and Tactic, - Environmental Test Methods and Engineering GI - Lubrication of Military Equipment. - Dissimilar Metals. - Cushioning, Anchoring, Bracing, Blocking, ani Waterproofing; with A

18、ppropriate Test Methods - Material Transportation System Dimensional ai Constraints, Definition Of. - Design for Internal Aerial Delivery in Fixed Aircraft . - Human Engineering Design Criteria for Milita Equipment and Facilities. - Noise Limits for Military Materiel. - Chock, Wheel. - Bracket Assem

19、bly, Liquid Container, Five Gal - Connector, Receptacle, Electrical - 12 Conta Attributes. Down Military Equipment. Characteristics. Vehi cl es. Intervehicular, 24 Volt, Waterproof. - Guide for the Selection of Lubricants, Fluid Preservatives and Specialty Products for use Equipment Systems. (Unless

20、 otherwise indicated, copies of federal and military specifi standards, and handbooks are available from the Standardization Docum Desk, Building 40, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents and Dub1 ications. The following Government documents and publicati

21、ons form a part of this document to specified herein. Unless otherwise specified, the issues are those c sol i ci tat ion. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-522L3F 38 = 999990b lLb042L 072 MIL-H-52213F(ME) DEPARTMENT OF LABOR (D

22、OL) 29 CFR 1910 - Occupational Safety and Heal th Standards (OSHA) (Application for copies should be addressed to the local DOL Office or to Superintendent of Documents, Government Printing Office, Washington, DC 20402.) DEPARTMENT OF TRANSPORTATION (DOT) Motor Vehicle Safety Standard (FMVSS). Motor

23、 Carrier Safety Regulations (FMCSR). (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, DC 20402.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. of the docum

24、ents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, the issues AMERICAN SOCIETY

25、OF MECHANICAL ENGINEERS (ASME) B31.1 - Power Piping. (Application for copies should be addressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3953 - Strapping, Flat Steel and Seals. D 4675 - Selection

26、and Use of Flat Strapping Materials. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) AMERICAN TRUCKING ASSOCIATIONS, INC. (ATA) Regular Common Carrier Conference (RCCC). RCCC RP#S110 - Vehicle Running Lamps. (A

27、pplication for copies should be addressed to the American Trucking Associations, Inc., 1616 P Street, NW, Washington, DC 20036.) AMERICAN WELDING SOCIETY (AWS) B2.1 - Welding Procedure and Performance Qualification. (Application for copies should be addressed to the American Welding Society, Inc., 5

28、50 Northwest Le Jeune Road, Miami, FL 33135.) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-52213F 38 999990b 11bOq22 TO9 MI L-H- 522 13 F (ME) ASSOCIATION OF AMERICAN RAILROADS (AAR) Rules Governing the Loading of Commodities on Open-Top C

29、ars. (Application for copies should be addressed to the Association of American FRICTION MATERIALS STANDARDS INSTITUTE, INC. Railroads, 50 F Street NW, Suite 7702, Washington, DC 20001.) Automotive Data Book. (Application for copies may be obtained from brake lining supplier or should be addressed t

30、o the Friction Materials Standards Institute, Inc., 370 Lexington Avenue, New York, NY 10017.) NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) ICs - 6 MG 1 - Motors and Generators. - Enclosures for Industri al Control s and Systems. (Application for copies should be addressed to the National El

31、ectrical SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) Manufacturers Association, 155 East 44th Street, New York, NY 10017.) SAE HANDBOOK 510 532 1 5429 543 1 5492 5516 5551 5553 5560 5561 5682 5683 5694 5697 5712 5759 582 1 5847 5849 5858 5928 51127 - Automotive and Off-Highway Air Brake Reservoir Performa

32、nce and - Tire Guards for Protection of Operator of Earthmoving Halage - Mechanical and Material Requirements for Externally Threaded - Automotive Gray Iron Castings. - Rivets and Riveting. - Hydraulic Hose Fittings. - Performance Levels and Methods of Measurement of Electromagnetic - Circuit Breake

33、rs. - Seven-Conductor Electrical Connector for Truck-Trai ler Jumper Cab1 e. - Electrical Terminals - Eyelet and Spade Type. - Rear Wheel Splash and Stone Throw Protection. - Tire Chain Clearance - Trucks, Buses (Except Suburban, Intercity, and Transit Buses), and Combinations of Vehicles. - Disc Wh

34、eel/Hub or Drum Interface Dimensions - Commercial Vehicles. - Safety Chain of Full Trailers or Converter Dollies. - Industrial and Agricultural Disc Wheel s. - Lighting Identification Code. - Electrical Wiring Systems for Construction, Agricultural and Off- - Trai 1 er Tow Bar Eye and Pi ntl e Hook/

35、Coupl er Performance. - Connection and Accessory Locations for Towing Multiple Trailers. - Electrical Terminals Blade Type. - Electrical Terminals - Pin and Receptacle Type. - Battery Cable. Identification Requirements. Machines. Fasteners. Radiation from Vehicles and Devices. Road Machines. 3 Provi

36、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-52213F 38 = 97999Ob llbO423 945 MIL-H-52213F (ME) 51128 51234 51292 - Automotive, Truck, Truck-Tractor, Trailer, and Motor Coach Wiring. 31402 - Low Tension Primary Cable. - Specification Definitions,

37、Off-Road Work Machines. - Automotive Air Brake Hose and Hose Assemblies. (Application for copies should be addressed to the Society of Automotive SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD) Engineers, 400 Commonweal th Drive, Warrendale, PA 15096.) Rule 442 - Usage of Solvents. (Application

38、 for copies should be addressed to the South Coast Air Quality Management District, 9150 E. Flair Drive, El Monte, CA 91731.) TIRE AND RIM ASSOCIATION, INC. (T shall be either the fire-tube, liquid-tube, or jacketed type; and shall be of all-welded steel construction. 9 Provided by IHSNot for Resale

39、No reproduction or networking permitted without license from IHS-,-,-MIL-H-522L3F 38 W 9999906 3360427 590 i 1 c 3.12 Insulation. The heat exchanger, except the combustion head, oil transmission lines, and overflow lines shall be insulated with either fiberglass felt insulation conforming to MIL-1-2

40、2023, type I, class 4, vermiculite solid block insulation, or a ceramic blanket type insulation for temperatures up to 1800 OF. Fiberglass felt insulation, when used, shall be applied to the outside of the welded steel jacket of the heat exchanger. The insulation shall be covered with a waterproof o

41、uter shell of not less than 0.0598-inch-thick sheet steel or not less than 0.090-inch-thick sheet aluminum. Vermiculite solid block insulation or ceramic insulation, when used, shall be applied to the inside of the welded steel jacket of the heat exchanger. The insulation shall be capable of maintai

42、ning the temperature of the outer shell and rear head at not more than 125 OF, plus the ambient temperature, after the heater has been operated at rated capacity for not less than 4 hours. If the temperature of the outer shell and rear head is more than 85 “F, plus the ambient temperature after the

43、heater has been operated at rated capacity for not less than 4 hours, the outer shell and rear head shall be shielded or guarded as specified in 3.3. 3.13 Burner. The burner shall be a single burner of the air-atomizing, mechanical-atomizing or pressure-atomizing type and shall burn fuel oil conform

44、ing to VV-F-800, grades DF-A, DF-1, and DF-2, and JP-8 turbine fuel conforming to MIL-T-83133. The burner shall be equipped with direct electrical ignition and shall be sequenced for automatic operation. The combustion controls shall be of the three-position high-low-off type or of the modulating ty

45、pe. rate shall be 33-1/3 110 percent of the maximum firing rate. reaction time shall be not more than 4 seconds. The burner shall be provided with all pumps, fans, blowers, and other accessories necessary for operation. Two 50- foot, oil-resistant, flexible fuel lines complete with appropriate fitti

46、ngs which can be connected to the fuel pump shall be provided. The fuel pump supply line shall include a replacable full-flow filtering device. Burner components shall be waterproofed. The low firing The flame-failure 3.13.1 ODeratinq seauence. The operating sequence shall be as follows: a. Burner s

47、tart by means of a manual starting switch. b. Fan and timer start for four air changes to purge the heater. purge time shall be not less than 15 seconds. c. After completion of purge, when all fuel safety and heater interlocks are closed and the combustion controls are at low fire, the timer shall a

48、ctuate the igniter and open the main fuel safety shutoff valve. d. When the flame-sensing device does not sense the main flame within 15 seconds after the main fuel valve opens, the device shall lock the burner out to prevent automatic recycling. When this occurs, a manual restart shall be required.

49、 e. After the main flame is detected, the combustion controls shall release from the low-fire position and go to high-fire position, except on the modulating-type burner which shall adjust to heat demand. f. After satisfying the heat demand, the combustion controls shall cause the burner to go from high-fire position to the off position and shall return sequentially to low-fire position and high-fire position upon a new demand for heat, except for the modulating-type