ARMY MIL-I-48634-1986 INTEGRATED CIRCUIT DIGITAL CMOS LOGIC ARRAY MONOLITHIC SILICON《铁制硅互补金属氧化物半导体制数字集成电路》.pdf

1、MIL-1-48634 (AR) 31 JULY 1986 MILITARY SPECIFICATION INTEGRATED CIRCUIT, DIGITAL, CMOS LOGIC ARRAY MONOLITHIC SILICON This specification is approved for use within the U.S. Army Armsiment, Munitions and Chemical Command, and is available for use by all Departments and Agencies of the Department of D

2、efense. 1. SCOPE 1.1 Scope. This specification establishes the performance, test, manufacturing and acceptance requirements for the logic array integrated circuit (I.C.) to be used in the M718El/M741El Mines. 2. APPLICABLE DOCUMENTS 2.1.1 L. Unless otherwise specified, the following specifications a

3、nd standards of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extend specified herein. SPEC1 FI CAT IONS MILITARY MI L-M- 3 8 5 1 O - Microcircuits, general MIL-1-4 5

4、208 - inspection system specification for. requirements. MIL-M-55565 - Microcircuits, preparation for delivery of. FSC 1375 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

5、from IHS-,-,-MIL-1-48634 (AR) STANDARDS MILITARY MIL-STD-105 - Sampling procedures and Tables for inspection by attributes. MIL-STD-883 - Test methods and procedures for microelectronics . MIL-STD-133 1 - Parameters to be controlled for the specification of micro- circuit s. MIL-STD-130 - Identifica

6、tion marking of U.S. military property. 2.1.2 Other Government documents, drawinqs, and publications. The following other Government documents form a part of this specification to the extend herein. DRAWINGS U. S. ARMY ARMAMENT, MUNITIONS AND CHEMICAL COMMAND PRODUCT AND PACKAGING DRAWINGS 9342578 -

7、 Logic Diagram, Logic Array, CMOS 9317646 - Qualification, Electronic Component. fzopies of specifications, standards, handbooks, drawings, and pubh.cations required by manufacturers in connection with specific acquisition functions should be obtained from the Contracting activity or as directed by

8、the contracting officer.) 2.1.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. 3. REQUIMMENTS 3.1 Parts and Materials. 3.1.1 Components. The I.C. shall comply with all the r

9、equirements of the applicable drawings, specifications and standards. 3.1.2 Metals. External metal surface shall be corrosion resistant or shall be plated or treated to resist corrosion. External leads shall meet the requirements specified in 3.5.3. 2 Provided by IHSNot for ResaleNo reproduction or

10、networking permitted without license from IHS-,-,-MIL-I-4b3Y 23 W 9977706 0322627 LI MIL-1-48634 (AR) 3.Pe3 Other materials. External. parts, elements or coatings including m-ot blister, crack, soften, flow or exhibit defect that adversely affect storage, operation or environmental capabilities of t

11、he integrated circuit delivered to this specification under the specified test condition. 3.2 1. 1.C. design and construction shall be in accordance with the requirements specified herein and in the applicable specifications OE drawings. 3.2.1 Dimensions. The package dimension shall conform to MIL-M

12、-38510- C, Case Outline D6, Configuration 1. 3.2.2 Packaqe. The finished component shall be supplied in a 18 pin, dual-in-line hermetically sealed package. The package shall be of the type shown in Figure 1, utilizing a ceramic lid, a ceramic base with gold deposit fo mounting the die, Alloy 42 or K

13、ovar solid metal lead frame thru to cavity with aluminum cladding, and a glass frit to accomplish the seal between the lid, lead frame and the base frit seal temperature shall be in excess of 400OC. No organic or polymeric material. shall. be used inside the package. 3.2.3 Passivation. The chip shal

14、l be passivated with silicon dioxide and/or silicon nitrade to render it impervious to contaminated environments. The bonding pad areas shall be the only areas with no surface passivation. 3.2.4 Static charge protect ion. Static charge protect ion shall be provided internally on all terminals. 3.2.5

15、 Pin assignments shall be as shown in Figure 2. 3.3 Desiqn documentation. When specified in the procurement document, design , topography and schematic circuit information for the microcircuit supplied under this specification shall be submitted to the procuring activity. Unless otherwise specified,

16、 all design documentation shall be sufficient to depict completely the physical and electrical construction of the microcircuit supplied under this specification, and shall be traceable to the specific production lot (s) and inspection lot codes under which microcircuit are manufactured and tested s

17、o that revisions can be identified. 3.3.1 Die topoqraphy. For microcircuit dies, there shall be an enlarqed color photograph (s) showing the topography of elements of the die to a minimum magniEication of 80X. If this results in a photograph larger than 8“ x lo“, the magnification may be reduced to

18、accommodate an 8“ x 10“ view. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-iBb34 13 9999906 0322b28 b 4 FRIT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SA SB PTB 1 - 2 c_I 3 MIL-1-4863

19、4 (AR) 4 GC - DD COW CLK -INCF, -1NIT FIGURE 2 -PIN ASSIGNbmNT 5 NC vss NC NC +INCR +INIT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-48643 (AR) 3.3.2 Logic diaqram. The actual logic diagrams of the microcircuit supplied under this specific

20、ation shall be provided, showing all the logic/circuit elements functionally designed into the microcircuit together with their values, when applicable. 3.3.3 Country of manufacturer. The component specified herein shall be manufactured, assembled and tested within the USA or its territories or by a

21、 foreign source complyinq with the provisions of the defense standardization manual, DOD 4120.3-M, paragraph 4-106.6, subject to the approval of the Government Technical Agency. (See 6.4). 3.4 Electrical requirements. 3.4.1 Maximum Rating. (As specified in Table 1) TABLE 1. MAXIMUM RATING Characteri

22、stic Symbol Ratinq (See 3.4.3) Temper at ur e D C Supply Voltage VDD -0.3 to +10 All Inputs VIN -0.3 to +10 Oper at ing TA (OP) -55 to +I25 Storage TA (STG) -65 to 1150 Unit Volts Volts OC oc - 3.4.2 Performance characteristics. (As specified in Table 2) 3.4.2.1 The I.C. circuit shall function in ac

23、cordance with the logic diagram as specified in dwg. 9342578 when operated under power supply requirements as specified in paragraph 3.4.3. 3.4.3 Power supply requirements. The component shall be capable of functioning with a power supply having the following requirements. 3.4.3.1 The output impedan

24、ce of the suDply source shall be 40 ohms minimum, 1,000 ohms maximum and shall be a 1.0 uf minimum capacitor across its output. 3.4.3.2 The supply voltage shall rise to 96% of its maximum value in less than 0.5 seconds. Noise voltage on the supplv output shall not exceed 5% VOD peak to peak and its

25、frequency shall not exceed 100 KHz. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L MIL-1-48634 13 E 977790b 0322633 h L I MIL-1-48634 (AR) 3.4.3.3 Electrical tests. Electrical tests shall verify conformance tsts of Tables II and III of this spec

26、ification. described in the test pattern shown in Table III. Table PIP shall be run with VDD values of 5 and 10 volts respectively. with all output pins open (uploaded) to meet the dynamic IDD requirements of Table PI. divide by 384 Eunetion (16 2/3% duty cycle) of the input at Pin 7. This output to

27、 be cheeke at any time during the test. The component input to output coding shall be as The pattern in The pattern should be repeated at the 3 VDD values In addition, Pin 3 (PTB) should provide a 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL

28、-1-48634 13 W 7797706 0322632 8 MIL-1-48634 (AR) TABLE II. PERFORMANCE CHARACTERISTICS: T= 25OC OUTPUT VOLTAGE OUTPUT OUTPUT (VOLTS) PINS CLOCK PARAMETER TEST CONDITIONS NO. CYCLE MAX MIN VOH VDD = 5.0V 1.2.9.17 88466 Inu = O.lma CGKnect a 46.4K resistor to Vss 10 11 O 2051 8 2052 3 Note 1 4.6 VDD =

29、 1O.OV IOH = 0.2ma Connect a 95.3K resistor to Vss 1,2,9,17 88466 10 O 11 2051 9.5 N/A I 8 2052 3 Note 1 VOL VDD = 5.0V IOH = O.lma Connect a 23.ZK resistor to VDD VOD = 1o.ov IOH = 0.2ma Connect a 47.5K reistor to VDD VDD = 5.0V IOH = O.lma Connect a 11.5K resistor to VDD 8,9,11 O 10 88466 3 Note 1

30、 O. 40 8,9,11 O 10 88466 0.50 3 Note 1 1,2,17 O O. 40 VDD = 5.0V LOH = 0.1 ma Connect a 23.7K resistor to VDD 1,2,17 O 0.40 Note 1: This output (PTB) is not reset by T/O (Pin 18). PTB stays high or 64 clock cycles and low for 320 clock cycles and may be measured at any clock count which achieves the

31、 desired state. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MEL-1-48634 (AR) TABLE PE. CL: T= 250 UNITS PARAMETER PINS NO. TEST CONDITIONS MAX MIN 6, 7, 16, 18 a - “ IH VDB = 5.0v 3.5 IDD 5 VDD = 7.ov STATIC All inputs DYNAMIC Input Pattern of-

32、Table III 100 MA 1 KHZ Clock rate TD and other timing KHZ (Pin 7) shall constitute verification that internal parameters Compliance with paragraph 3.4 VDD = 5.0 Volts and CLK = 1.0 propagation delay and timing parameters satisfy the requirements of this specification. 9 Provided by IHSNot for Resale

33、No reproduction or networking permitted without license from IHS-,-,-MIL-I-4b34 13 7777706 O322634 I W TABLE 111 TEST PATTERN 1 CLOCK CYCLE TOTAL OF 1024 CLOCK CYCLES TOTAL OF 1024.CLOCK CYCLES 2049 2050 205 1 2052 2053 2054 3 CLOCK CYCLES MIL-1-48634 (AR) INPUTS OUTPUTS .TEST 1 SO + SO 3 t - DURATI

34、ON OF 960-1024 CLOCKS IS ACCEPTABLE - - - - - - TABLE III. TEST PATTERN. . 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE III (6C“ INUED) 3 CLOCK CYCLES 1975 CLOCK CYCLES TOTAL OF 1022 CLOCK CYCLES MIL-1-4 8634 (AR) D 2058 - 2059 - 2060 CI

35、c 5064 2065 - 2066 4042 506 1 5 5066 5067 INPUTS OUTPUTS - - TD SO - SO 3 TABLE III. (Contd) u I KE - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-cr. . TABLE Ill (C ONT I NUED) MIL-I-48b34 13 W 7977706 032263b 5 JI OUTPUTS INPUTS COnTD SPIKE TOTA

36、L OF 3069 CLOCK CYCLES TOTAL OF 593 CLOCK CYCLES TABLE III. (Contd) 12 , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8739 1740 874 1 8742 MIL-1-4 8 634 (AR) 8746 8747 8748 8749 8750 TABLE III. (Contd) u I NBUTS OU?BUVS 6 Ja CONTD SPIKE Provided b

37、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-Ltb3Y 13 I 77Ob 0322638 7 I! TABLE III (CONTINUED) 8753 8754 8755 8756 8757 8758 TOTAL OF 977 CLOCK CYCLES 9737 INPUTS IC OUTPUTS f PTABLE 3072 CLOCK CYCLES 12810 TABLE III. (Contd) SPI KE D SB CLOCKS Provi

38、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-48634 (AR) TABLE III. (Contd) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE III (CONTINUED 1008 CLOCK CYCLES MIL-I -4 8 6 34 (AR 1. INPUTS OUTP

39、UTS f Y TABLE III. (Contd) 16 4 C - I - O - I F 1 TEST 3b CONTD SPIKE II O I BACK TO +INIT AI TEST 4 t2 I WRAf10)(,OF +INIT IS A VARIABLE 960-1024 CLOCKS ME ACCEPTABLE t2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-4b34 13 7777706 03226111

40、7 W. MIL-1-48634 (AR) TABLE III (CONT ICJYED) je71 CLOCK CYCLES 14 CLOCK CYCLES TABLE III. (Contd) 17 t2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-1-4 86 34 (AR) TABLE 111 (CONT I NU EO) 1022 CLOCK CYCLES INPUTS rc OUTPUTS f V CONTD 4 CLO

41、CK CYCLES . .- . TABLE III. (Contd) 7 t2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-48634 (AR) QU1 PUTS D t2 t I TABLE III. (Contd) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-4 8

42、 6 34 (AR) TABLE III (CONTINUED) TABLE III. (Contd) 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-48634 13 7779736 0322645 6 - MIL-1-4 8 634 (AR) o . _. . I NPYT OIITPT TABLE III (CONY IHUEB 3091 CLOCK KYCLES 63 KL06K CYua 5 KLOCK CYCLES 1

43、 32264 42265 i 35337 35338 35339 35483 35404 35405 3541 1 354 12 TABLE III. (Contd) 21 -7 - X i- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE 111 (C OHT I NUED) 354 13 i- 69 CLOCK CYCLES 35483 - 35484 i003 CLOCK CYCLES 36488 36489 - 3071 CLO

44、CK CYCLES 3956 1 39562 * - : 16 CLOCK CYCLES i9579 MIL-1-4 8634 (AR 1” I WPUTS OUTPUTS f h TABLE III. (Contd) 22 c I . . :- +MAX -7- -MX If -4 AX Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-OC K ES 78 CLOCK CYCLES MIL-1-4 8634 (AR) I IIPUTS 5(3 C

45、YC TABLE III. (Contd) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-4 8 634 (AR) TABLE III (C ONT I nu ED 1 39665 c 982 CLOCK CYCLES 40648 ION 40649 c 3071 CLOCK CYCLES 43722 43723 c 43 CLOCK CYCLES 43767 43?68 43769 43770 - TABLE III. Contd)

46、 24 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-1-48634 13 7977706 0322b47 3 m MIL-I -4 8 6 34 (AR) INPUTS OUTPUTS f TABLE III (CONT INUD CT I ON TABLE III. (Contd) :. . Provided by IHSNot for ResaleNo reproduction or networking permitted wit

47、hout license from IHS-,-,-MIL-1-48634 (AR) INPUTS A . OUTPUTS TABLE III (CONT I NUED) 43786 957 CLOCK CYCLES 44744 44745 - c 3071 CLOCK CYCLES 47817 47810 (I 66 CLOCK CYCLES 47085 47886 47887 - FUi TABLE III. (Contd) TI ON - 26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-L+b34 13 I 7779906 O322651 L m MIL-1-48634 (AR) I MPUTS A OUtPUtS 7b PA-F 4-FUNCTION TABLE III. (Contd) 27 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE III (CONT I NUED) 479