ARMY MIL-I-50860 (1)-1983 IGNITION ELEMENT ELECTRICAL PARTS FOR《电气点火元件零件》.pdf

1、MIL-1-50860 AMENDMENT 1 30 June 1983 MILITARY SPECIFICATION IGNITION ELEMENT, ELECTRICAL, PARTS FOR This amendment forms a part of Military Specification MIL-1-50860 (MU) dated 18 February 1971, and is approved for use by the U.S. Army Armament Research and Development Command and is available for u

2、se by all Departments and Agencies of the Department of Defense. PAGE 3 3.3, Line 2, delete: “ . 1.30.“ and substitute: Il .,. 1.40. “ . 3.4 Delete in its entirety. 3.5: Lines 2 and 3 delete: “ . direction.“ and substitute: “.plane.“. Line 3, delete: H . 30 pounds. .“. “ . 40 pounds.“ and substitute

3、: PAGE 6 4.3.2, Last line, delete: “. 4.3.5)“ and Substitute ri 0 4.3.4)“. 4.3 . 2.1: Category 104, delete: pattern diameter to I.D. of cup“ and substitute: position of intersection of slit pattern to I.D. of cup.“ “True position of lance “True Category 204 delete: ,hole“ and substitute: . . .cup wa

4、ll“ . *US. GOVERNMENT PRINTING OFFICE 1983-705-040/5023 FSC 1320 1 of 3 P Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- MIL-1-50860 (I) 13 W 9999906 0331779 I MIL-I -50 86 O AMENDMENT I PAGE 7 4.3.2.3, Category 205, delete “(see 3.6)“ and substi

5、tute: “(see 3.6 and 6.6)“. PAGE 8 4.3.2.4, Category 102, delete in its entirety. PAGE 9 4.3-2.7, Category 102: Delete: “Inside diameter of outer edge“ and substitute: “Outside diameter“. Delete: “07002“ and substitute “07006“ . PAGE 10 Line 2 delete: I. . .MIL-STD-414, Inspection Level IV .I1 and su

6、bstitute: I. . .MIL-STD-105, Sampling Plan S-4 .(I. Last line, delete: “(see 6.6)“. 4.3.3.3, Delete in its entirety and Substitute: “Relative quickness (informational) . The relative quickness of the front support shall be determined at the the of first article testing at 8500 psi using a sufficient

7、 number of randomly selected front supports to provide a loading density of 0.2 g/cc in a nominal 200 cc closed bank. A minimum of three separate tests shall be conducted. Testing shall be in accordance with MIL-STD-286, Method 8Ol.l. and shall be conducted at 70 + 2%. A minimum of three comparison

8、tests shall be-performed using M26El. propellant (See 6.5) .“ 2 - _a i-i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-I-SObO (1) 13 H 777970b 0333800 4 MIL-I -SO 8 6 O AMENDMENT 1. PAGE 1.1 4.3.3.4: Lines 2 and 5 delete: three references to l.

9、 direction .“ and substitute “.plane. Il Line 3 delete: . . .“MIL-STD-414, Inspection Level IV .I Line 7 delete: “.(see 6.6)“. and substitute I. MIL-STD-LOS Sampling plan S-4. . .I. 4.3.3.5: Li.ne 2 delete: I .MIL-STD-414, Inspection Level IV .I Line 6 delete: “.(see 6.6)“. and substitute II. MIL-ST

10、D-105, Sampling Plan S-4 .I. PAGE 1.4 6.5, Delete in its entirety and substitute: “6.5 submission of test results. One copy of all results of informational testing shall be forwarded to Picatinny Arsenal, ATTN: SMUPA-ND2.“ 6.6, Delete in its entirety and substitute: “5.6 Definition of chips. Chips a

11、t intersecting areas on the front support may be 3/l6 inch maximum in any dimension. If this condition exists, then any other set of adjacent intersecting areas shall be limited to chips of 7/13 inch maximum in any direction.“ Cus to i an: Afiny-AR P repar ing Activity : Amy-AR (P r oj ec t 13 20 -A7 2 5 ) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-