ARMY MIL-J-43923 C-1990 JACKET FLYER'S LIGHTWEIGHT (EXPANDABLE WRISTS AND WAIST)《轻型飞行员夹克(可扩大腰和腕)》.pdf

1、MIL-J-43723C 4 W 7779706 OLt23754 2 - MIL-J-43923C(GL) 13 April 1990 SUPERSEDING MIL-J-43923B(GL) 28 December 1984 MILITARY SPECIFICATION JACKET, FLYERS, LIGHTWEIGHT, (EXPANDABLE WRISTS AND WAIST) This Specification is approved for use by the Natick Research, Development, and Engineering Center, Dep

2、artment of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a self-lined jacket made of a high temperature resistant aramid oxford cloth. 1.2 Classification. The jacket shall be of one type in the following

3、 sizes as specified (see 6.2). Schedule of sizes X-Sma 11 Short Regular Long Small Short Regular Long Medium Short Regular Long Large Short Regular Long X-Large Short Regular Long i I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving th

4、is document should be addressed to: 01760-5014 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. .S. Army Natick Research, Development, and Engineering Center, Natick, MA i AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approve

5、d for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-43723C 84 7777906 0423755 4 I 2. APPLICABLE DOCUMENTS 2.1 Government documents, 2.1.1 Specifications, standards, and handbooks. The following speci

6、fications, standards, and handbooks form a part of this document to the extent specified herein, Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the so

7、licitation (see 6.2). SPECIFICATIONS FEDERAL A-A-50083 - Bag, Plastic, Folded Garment T-T-88 1 - Twine, Cotton, Seine V-F-106 - Fastener, Slide, Interlocking DDD-L-20 - Label: For Clothing, Equipage, and Tentage, (General PPP-B-636 - Boxes, Shipping, Fiberboard Use) MIL1 TARY MIL-C-3735 MIL-F-21840

8、MIL-L-35078 MIL-T-43548 MIL-T-43636 MIL-T-43709 MIL-C-43842 MIL-T-44100 MIL-T-83193 Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted Fastener Tapes, Hook and Loop, Synthetic Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; Genera? Specification

9、 For Po lyes ter-Covered Thread, Polyester Core: Cotton-, Rayon-, or Thread, Aramid Tape, Textile, Aramid Cloth, Oxford, Aramid Thread, Para-Aramid, Spun, Intermediate Modulus Thread, Aramid, Spun Staple STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams and Stitching

10、s MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members.for Containers and Pallets Attributes 2 Provided by IHSNot for ResaleNo reproduction or networking perm

11、itted without license from IHS-,-,-MIL-J-Lt3723C L( M 7779706 0423756 6 (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 No

12、n-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODICC cited in the solicitation. Unless otherwise specified, the issues

13、of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materia

14、ls, 1916 Race Street, Philadelphia, PA 19102-1187.) THE COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America Department of Defense Standard Color Card for Sewing Threads (Color cards may be available from the Color Association of the United Sates, 343 Lexington Avenue, New York, NY

15、10016-0927. If color cards are not available from the Color Association, individual color samples may be obtained from the contracting activity or as directed by the contracting activity.) (Non-Government standards and other publications are normally available from the organizations that prepare or

16、distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this

17、 document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide sample. Guide samples, when f

18、urnished, are solely for guidance and information to the contractor (see 6.4). Variations from this specification may appear in the sample, in which case this specification shall govern. 3.3 Materials. It is encouraged that recycled material be used when practical as long as it meets the requirement

19、s of this specification. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.1 Basic material. The basic material shall be 6.0 ounce high temperature resistant, aramid oxford cloth conforming to MIL-C-43842. The color shall be Olive Green 106. 3.3.

20、2 Knit wrist cuffs and waistband material. 3.3.2.1 Wrist cuffs. The knit wrist cuffs shall be Olive Green 106 and shall conform to type IV, class 2 of MIL-C-3735. 3.3.2.2 Waistband. The knit waistband shall be Olive Green 106 and shall conform to type IV, class 3 of MIL-C-3735. 3.3.3 Fastener tapes.

21、 The nylon fastener tapes shall be Green, Shade 3421 and shall conform to type I, class 2, 1 inch and 5/8 inch widths of MIL-F-21840. Nylon tape, 1-1/2 inches wide may be substituted for the 5/8 inch tape. 3.3.4 Tape, .aramid. The tape for hanger loops and for slide fastener thongs shall conform to

22、MIL-T-43709. 3.3.5 Cord. The cord beading used for welts of front opening shall conform to type I, No. 18 of T-T-881. 3.3.6 Thread. . 3.36.1 Thread, aramid: .The aramid thread shall conform to type I, sizes B and E of MIL-T-43636, dyed Olive Drab S-1, C.A. 66022. As an alternate, thread sizes T-60 a

23、nd T-90 conforming to MIL-T-83193 or sole thread size T-35 conforming to MIL-T-44100 may be respectively substituted to replace the size B and E of MIL-T-43636 threads. 3.3.6.2 Thread, polyester core. Cotton-, rayon-, or polyester-covered polyester core thread conforming to ticket No. 50, 2-ply of M

24、IL-T-43548 may be used as an alternate thread for bartacking. The thread shall be dyed Olive Drab S-1, C.A. 66022 and shall show fastness to laundering equal to or better than the standard sample. When no sample is available, the thread shall show “good“ fastness to laundering. 3.3.7 Fasteners, slid

25、e. The slide fasteners shall be brass with a black chemical finish, and shall conform to V-F-106. 3.3.7.1 Front, The fastener for the jacket front shall conform to type IV, style 8, size M, short tab pull, with, the chain of the fo.llowing lengths in inches : Size Short Regular Long - X-Sma 11 Small

26、 Medium Large X- La r g e 19 20 19-1/2 20-1/2 20 21 20-1/2 21-1/2 21 22 4 21 21-1/2 22 22-1/2 23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.7.2 Pencil and utility pocket. The fastener for the pencil and utility pocket shall conform to type I

27、, style 7, size M, short tab pull, 4-3/4 inch chain. 3.3.7.3 Slide fastener tape. The slide fastener tape shall be made of a aramid nylon tape, shade S, Cable No. 66519, and shall show “good“ fastness to laundering. Color matching of the fastener tape under incandescent lamplight at 2300 f 100K shal

28、l be exempt. 3.3.8 Resinous sealer. The material for dipping the ends of slide fastener thongs (see operation 1.c) to prevent fraying, shall be a colorless, non- combustible resin (see 6.5). As an alternate the ends may be cut by hot wire or a hot bladed strip cutter. 3.3.9 Labels. Each jacket shall

29、 have (a) a class 1 identification label, a class 2 size label, and a class 3 instruction label; (b) a class 2 size label and a class 15 combination identification and instruction label; or (c) a combination of the class 1 identification and class 2 size labels and a class 3 instruction label confor

30、ming to type VI of DDD-L-20. The labels shall show fastness to laundering. When a combination identification-instruction label is used, the item nomenclature shall not be repeated. The size label shall contain the following information for each respective size. Description information shall be print

31、ed in letters and numerals not less than 10-point and as follows: X-Small - Short X-Small - Regular X-Small - Long Chest: Up to 33 inches Height: Up to 67 inches Stock No.: NATO size: 6070/7484 Small - Short Chest: 33 to 37 inches Height: Up to 67 inches Stock No. : NATO size: 6070/8494 Chest: Up to

32、 33 inches Height: 67 to 71 inches Stock No.: NATO size: 7080/7484 Chest: Up to 33 inches Height: 71 inches up Stock No.: NATO s ize : 8090/7484 Small - Regular Chest: 33 to 37 inches Height: 67 to 71 inches Stock No.: NATO size: 7080/8494 Small - Long Chest: 33 to 37 inches Height: 71 inches up Sto

33、ck No.: NATO size: 8090/8494 Medium - Short Medium - Regular Medium - Long Chest: 37 to 41 inches Chest: 37 to 41 inches Chest: 37 to 41 inches Height: Up to 67 inches Height: 67 to 71 inches Height: 71 inches up Stock No.: Stock No.: Stock No: NATO size: 6070/9404 NATO size: 7080/9404 NATO size: 80

34、90/9404 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-43723C 4 W 7777706 0421757 1 Large - Short Chest: 41 to 45 inches Height: Up to 67 inches Stock No.: NATO size: 6070/0414 X-Large - Short Chest: 45 inches up Height: Up to 67 inches Stck

35、 .No. : NATO size: 6070/1424 Large - Regular Chest: 41 to 45 inches Height: 67 to 71 inches Stock No. : NATO size: 7080/0414 X-Large - Regular Chest: 45 inches up Height: 67 to 71 inches Stock No.: NATO size: 7080/1424 Large - Long Chest: 41 to 45 inches Height: 71 inches up Stock No.: NATO size: 80

36、90/0414 X-Large - Long Chest: 45 inches up Height: 71 inches up Stock No.: NATO size: 8090/1424 The instruction label shall contain the following information: JACKET, FLYERS: LIGHTWEIGHT, (EXPANDABLE.WRISTS AND WAIST) This jacket is of low flammability. No other special flame resistant treatments ar

37、e required. 1. The jacket can be machine washed or dry cleaned.in accordance with Jacket may be hand laundered; make sure soap is established procedures. thoroughly rinsed out. 2. WARNING: Launder with slide fasteners and hook and loop fasteners close! Do not press hook and loop fasteners. thereafte

38、r, launder in accordance with Formula IX (no bleach) of TM 10-280, field laundry and Natick Formula X, fixed laundry for the retreatment of anti- static agent. After 10 laundering cycles and 3. DO NOT STARCH, Starch will burn. If starched, thorough laundering will return this garment to its fire ret

39、ardant condition. 4, Color fading does not diminish the flame retardant properties of this garment DO NOT REMOVE THIS LABEL . 3.4 Design. closure, Jacket has a collar with tab closure and diagonal side pockets with flaps with hook and loop closure. pocket. The jacket is single breasted with a front

40、slide fastener The left sleeve has a utility and pencil Jacket is fully self-lined. The cuffs and waistband are rib knit. 3.4.1 Figure. Figure 1 is furnished for information purposes only. To the extent of any inconsistencies between the written specification and the figure, the written specificatio

41、n shall govern. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-43723C BL( U 7777706 0421760 8 U 3.5 Patterns. Standard patterns which provide a 1/2 inch seam allowance for double-lapped, double-stitched seams attaching cuffs to sleeve and at

42、taching waistband to jacket and 3/8 inch for all other seams will be furnished by the Government. The standard patterns shall not be altered in any way and are to be used for cutting contractors working patterns. The working patterns shall be identical to the standard patterns. 3.5.1 List of pattern

43、 parts. The component parts of the jacket shall be cut from materials specified in accordance with the number of parts indicated in table I. TABLE I. List of pattern parts Mat er ia 1 Nomenclature Cut parts 6 oz. aramid nylon oxford Front Back Collar (top collar and interlining) Under col lar Neck t

44、ab Top sleeve Undersleeve Pocket Welt Utility pocket Pencil pocket upper Pencil pocket lower Slide fastener cover Front facing Front extens Front lining Back lining Top sleeve 1 Unders leeve Pocket flap on ning ining 2 1 2 1 2 2 2 4 2 1 1 1 1 2 2 2 3.6 Construction. 3.6.1 Stitches, seams and stitchi

45、ng. Stitch, seam and stitching types specified in table II shall conform to FED-STD-751. Where two or more seam or stitch types are given for the same part of an operation, any one of them may be used. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the jacket. The

46、gage of stitching on double lapped and double stitched seams shall be 1/4 to 5/16 inch, but the same gage shall be used on all double stitched seams throughout the jacket. The gage of stitching for safety stitch construction shall be 3/8 inch . The guides and knives on the safety stitch machines sha

47、ll be set to trim only the ravelled ends of the fabric. Seam 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-allowances shall be maintained with seams sewn so that raw edges, runoffs, twists, pleats or puckers will not result, All seams shall start

48、 and finish evenly. tension. Seams required to be worked out having a depth between the fold of 1/16 inch or more shall be considered a defect. Thread tension shall be maintained so that there is no tight or loose 3.6.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitche

49、d not less than 1/4 inch except where ends are turned under or caught in other seams or stitching. overlapped not less than 1/2 inch except on labels where a minimum of three stitch overlap is required. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. The lock shall be imbedded in the materials s