ARMY MIL-L-43579 C (2)-1989 LINER TROUSERS CHEMICAL PROTECTIVE《化学防护裤衬里》.pdf

1、MIL-L-43577C (2) 84 W 7777706 0374737 5 - W 545-a 7 (-D( MIL-L-43579C AMENDMENT 2 26 September 1989 SUPERSEDING AMENDMENT 1 14 June 1985 MILITARY SPECIFICATION LINER, TROUSERS, CHEMICAL PROTECTIVE This amendment forms a part of Military Specification MIL-L-43579C, dated 7 October 1982, and is approv

2、ed for use by all Departments and Agencies of the Department of Defense. PAGE 1 9: 2.1: Delete and substitute: “2.1 Government documents. 2.1.1 Specifications, standards, and handbooks, The following specifi- cations, standards, and handbooks form a part of this document to the extent specified here

3、in. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2).“ PAGE 2 2.1, under “SPECIFICATION FEDERAL“ : Delete “UU-P-268, Paper, K

4、raft, Wrapping“ and add “A-A-203, Paper, Kraft, Untreated“. Under “SPECIFICATIONS MILITARY“: Add “MIL-L-35078, Loads, Unit: Preparation of Semiperishable Subsistance Items; Clothing, Personal Equipment and Equipage; General Specification For“ and “MIL-T-43548 - Thread, Polyester Core: Cotton-, Rayon

5、-, or Polyester-Covered“. Under “STANDARDS MILITARY“: Add “MIL-STD-147-Palletized Unit Loads“ and MIL-STD-731- Quality of Wood Members for Containers and Pallets“, Delete “MIL-STD-1188-Commercial Packaging of Supplies and Equipment“. AMSC NIA Page 1 of 6 FSC 8415 DISTRIBUTION STATEMENT A. Approved f

6、or public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43577C (2) 84 9747906 0374738 7 I MIL-L-435 79C AMENDMENT 2 PAGE 2 (contd) Delete source paragraph and substitute: “(Unless otherwise indicated, copie

7、s of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099. I f: 2.1.1: Delete and substitute: “2.2 Non-Government publications. The following document forms a part. of t

8、his document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documen

9、ts cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government

10、 standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents - also may be available in or through libraries or other informational services. )I * 2.2: Delete and substitute: “2.3 Order of precedence. In the event of a conf

11、lict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained.“ PAGE 4 s: 3.2.6: Add the following to the end of paragraph

12、: “As an alternate, the thread shall be cotton or polyester covered polyester core, Olive Drab S-1, C.A. 66022, 50, 2 or 3 ply, (for cotton ticket number 30) and 70, 2 or 3 ply (for cotton ticket number 50) conforming to MIL-T-43548.“ PAGE 10 * Table I, operation 7a, under “Bobbin/Looper“ column for

13、 stitch type 401: Delete “30-3“ and substitute “50-3“. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43579C AMENDMENT 2 PAGE 14 Table I, operation 15a: Delete and substitute “15 a. Trim all ends of stitching to 1/4 inch maximum length throu

14、ghout (inside and outside) and remove loose threads from the trousers. I PAGE 15 Table II: Delete all inseam lengths and substitute “37“ for each size. PAGE 18 4.2, under “Cleanness“: Delete defect b. entirely and substitute “b. Thread ends not trimmed to 1/4 inch maximum length throughout (inside a

15、nd outside) or loose thread ends not removed from liner (to be scored only when the condition exists on major portion of liner), Minor B“. PAGE 25 4.2.4: Delete and substitute: “4.2.4 Packaging examination. The fully packaged end items shall be examined for the defects listed below. The lot size sha

16、ll be expressed in units of shipping containers. fully packaged. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. The sample unit shall be one shipping container Exam i ne Defect Marking (exterior Omitted; incorrect; illegible; of improper

17、 size, and interior) location, sequence, or method of application Ma ter i a 1 s Any component missing, damaged, or not as specified Workmanship Content Inadequate application of components, such as incomplete sealing or closure of flap, improper taping, loose strapping, or inadequate stapling Bulge

18、d or distorted container Number per container is more or less than required Number of liners per bundle is more or less than Size shown on one or more liners not as specified Improperly folded liners, inadequately lined bundles, required L/ on container L/ contents improperly covered with paper - i/

19、 For this defect, two bundles from each container in the sample shall be examined. I 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43577C (2) 4 777770b 0374740 5 mil-1-43579c AMENDMENT 2 PAaE 25 (contd) Add the following new paragraph: “4.2

20、.5 Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. palletized unit load, fully packaged. The inspection level shall be S-1 and the AQL, expressed in terms of defe

21、cts per hundred units, shall be 6.5. The sample unit shall be one Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as specified Interlocking of loads not as specified Load not bonded as specified Weight Exceeds maximum

22、 load limits Marking Omitted; incorrect; illegible; of improper size, location, sequence, or method of application“ PAGE 26 - 5.1.2: Delete “MIL-STD-1188“ and substitute “ASTM D 3951“. * 5.2.1 Level A packing, line 10: Delete “type I, grade B of UU-P-268“ and substitute “A-A-203“. Delete the last se

23、ntence and substitute “Shipping containers shall be arranged in unit loads in accordance with MIL-L-35078 for the type and class of load specified (see 6.2). When unit loads are strapped, strapping shall be limited to nonmetallic strapping, except for type II, class F loads.“ 2: 5.2.2 Level B packin

24、g, lines 10 and 11: Delete “Type I, grade B of LJLi-P-268“ and substitute “A-A-203“. Delete the last sentence entirely. PAGE 27 5.2.3, line 2: Delete “MIL-STD-1188“ and substitute “ASTM D 3951“. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L

25、-43577C (2) 4 = 7777906 0394741 7 - MIL L 435796 - AMENDMENT 2 PAGE 27 (contd) Jc 5.3 and 5.3.1: Delete and substitute “5.3 Palletization. When specified (see 6.2), liners, packed as specified in Pallet type shall be type I (4-way entry), type IV Pallets shall be fabricated from wood 5.2.2 or 5.2.3,

26、 shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD-147. or type V in accordance with MIL-STD-147. groups I, II, ILI, or IV of MIL-STD-731. Each prepared load shall be bonded with primary and secondary straps in accordance with bonding means C and D or film bondin

27、g means F or G. the appendix of MIL-STD-147. Interlocking of loads shall be effected by revers- ing the pattern of each course. Pallet pattern shall be number 3 in accordance with 5.4 Marking. In addition to any special marking required by the contract or purchase order, unit packs, shipping contain

28、ers, and palletized unit loads shall be marked in accordance with MIL-STD-129 or ASTM D 3951, as applicable. 6.2: Add the following new subparagraphs: “(f) Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.1.1 and 2.2). (g)

29、 (h) Type and class of unit load required (see 5.2.1). When palletization is required (see 5.3) .“ Add the following new paragraph: 2; “6.6 Subject term (key word) listing. Clothing i nne rwe a r I NOTE: Changes from the previous amendment. The margins of this amendment are marked with an asterisk o

30、r vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned t

31、o evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment.“ 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Custodians: Army - GL Navy - NU Review activities: Army - MD Navy - MC DLA - CT User activities: Navy - OS, CG Preparing activity: Army - GL (Project 8415-0676) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-