ARMY MIL-M-53008 (2)-1985 MOUNTING KIT ROLLER MINE CLEARING TRACK-WIDTH TANK-MOUNTED《排雷滚筒式安装夹具盒 坦克安装的磁迹宽度》.pdf

1、4 MIL-M-53008(ME) AMENDMENT 2 17 October 1985 SUPERSEDING AMENDMENT 1 16 May 1983 MILITARY SPECIFICATION MOUNTING KIT, ROLLER, MINE CLEARING: TRACK-WIDTH, TANK-MOUNTED This amendment forms a part of MIL-M-53008(ME), dated 8 July 1982, and is approved for use within the USA Belvoir Research and Devel

2、opment Center, Department of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1.1, under SPECIFICATIONS, MILITARY add: * “M I L-C-4 6 1 6 8 * MIL-C-22750 MIL-R-53007 - Coating, Aliphatic Polyurethane, Chemical - Coating, Epoxy Polyamide. - Roll

3、er Kit, Roller, Mine Clearing: Agent Resistant. Track-Width, Tank-Mounted . PAGE 2 * Under STANDARS, MILITARY add: “MIL-STD-838 MIL-STD-889 - Lubrication of Military Equipment. - Dissimilar Metals.“ 2.1.1, after STANDARDS add: “ IlANDBOOKS MILITARY MIL-HDBK-113 - Guide for the Selection of Lubricant

4、s, Fluids, Preservatives and Speciality Products for Use in Ground Equipment Systems.“ FSC 1095 DISTKIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Page 1 of 9 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted

5、without license from IHS-,-,-MIL-M-53008 (2) IO m 7777706 0334539 I m MIL-M-S3008(ME) AMENDMENT 2 PAGE 3 I * I * Under 3.4, add new paragraphs: “3.4.1 Material deterioration and control. The item shall be fabricated from compatible materials, inherently corrosion resistant, or treated to provide pro

6、tection against the various forms of corrosion and deterioration that may be encountered in any of the applicable operation and storage environments to which the item may be exposed. 3.4.2 Dissimilar metals. Dissimilar metals shall not be used in intimate contact with each other unless protected aga

7、inst galvanic corrosion. Dissimilar metals and methods of protection are defined and detailed in MIL-STD-889. 3.4.3 Identification of materials and finishes. The contractor shall identify the specific material, material finish or treatment for use with components and subcomponents, and shall make in

8、formation available upon request to the contracting officer or designated representative.“ * 3.7.1, line 3, delete “Type A color forest green.“ and substitute “Type F or G as applicable. camouflage green 383 conforming to MIL-C-46168. The kit shall then be overcoated in accordance with the Governmen

9、t furnished camouflage patterns with MIL-C-46168 top coat of the colors specified in the camouflage patterns.“ Unless therwise specified (see 6.2) top coat color shall be * 3.7.2, line 3, delete “Type A, color white enamel.“ and substitute “Type F or G as applicable, color white 17925 in accordance

10、with MIL-C-22750.“ PAGE 4 3.9.2, line 8, after “used.“, add the following new sentences: “Welds shall not exceed the next 1/16 inch larger size for welds up to 318 inch. larger size. For welds 318 inch and larger the size shall not exceed the next 1/11 inch Welds shall not be undersize.“ 3.10, add n

11、ew paragraphs: “3.10 Installation Test. The installation test shall be conducted in accord- ance with 4.4.3.2.“ “3.11 Operational Test. The operational test shall be conducted in accord- ance with 4,4.3.3.“ * 3.12 Government-furnished property. The following property will be furnished by the Governm

12、ent (see 6.5): 2 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-, MIL-M-5 3008(ME) AMENDMENT 2 Item - No. Description Identification Quantity 1 Pattern drawings Camouflage patterns AS required“ * 3.13 Lubrica

13、nts. The procedure for the selection of lubricants shall be in accordance with MIL-STD-838, section 5. Lubricants selected shall be in accordance with MIL-HDBK-113, chapter 2. When the specification of the lubricant selected includes a requirement for a qualified products list (QPL), the lubricant s

14、upplied shall be from a source that is listed on the applicable QPL . It PAGE 6 Add new paragraphs: “4.4.3 Test s. “4.4.3.1 Samples. Samples selected in accordance with 4.4.1 shall be subjected to the following tests, plus any other tests specified by the contracting activity to comply with requirem

15、ent of 3.3. shall be cause for rejection.“ Failure of any test “4.4.3.2 Test Installation of Mine Roller. One mounting kit shall be installed on an M60 tank. One roller kit, mine clearing in accordance with MIL-R-53007 shall be mounted on to the installed mounting kit using the winches and other mou

16、nting equipment provided with the mine roller and mine roller mounting kit. The mine roller shall be released and remounted at least twice using the hydraulic release mechanism and twice using the manual release mechanism. During the mounting and release of the roller, the operation shall be observe

17、d and any interference of the parts noted.“ “4.4.3.3 Operational Test. Following installation of a mine roller, an operational test of the mounting kit shall be conducted consisting of 2 miles of level cross-country operation. During the operational test, both left and right turns and forward and re

18、verse operations shall be demonstrated. Following the operational test, the mine roller shall be released and remounted at least twice using the hydraulic release mechanism and twice using the manual release mechanism. During the mounting and release of the roller, the operation shall be observed an

19、d any interference of the parts noted. Initial production operational tests for a mine roller kit and a mine roller mounting kit may be run concurrent iy . I PAGE 7 Table I, under major characteristics add: 3 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or ne

20、tworking permitted without license from IHS-,-,-Quality conformance 2 X X X X X X X X X X X X X X X X X MIL-M-5 3008 (ME ) AMENDMENT 2 “TABLE I. Examination schedule. Characteristics 3 1. Camouflage pattern data not as specified. MAJOR 101. 102. 103. 104. 105. 106. 107. 108. 109. 110. Dimensions are

21、 not as specified. Parts and components are not c omp 1 et e . Material is not as specified. Materials are not resistant to corrosion or deterioration or treated to be made resistant to corrosion or deterioration for the applicable storage and operating environment as specified. Dissimilar metals as

22、 specified in MIL-STD-889 are not effectively insulated from each other as specified. Contractor does not have documenta- tion available for identification of material, material finishes or treatments as specified. Safety is not as specified. Parts are not interchangeable. Treatment and painting not

23、 as specified. Paint color not as specified. 111. 112. Welding certification is riot 113. Mounting kit cannot be installed. 114. Interferance noted. Workmanship is not as specified. furnished. 115. Operation not as specified. 116. Camouflage patterns not as specified. 4 Licensed by Information Handl

24、ing ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I Quality conformance 2 I initial Requirement Characteristics paragraph 3 4 roduc t ion I+- X x I 117. Lubricants not as specified. 3.13 MINOR 201. Identification marking is not as 3.8“ spec

25、ified. x MIL-M-S3008(ME) AMENDMENT 2 “TABLE I. Examination schedule. (Continued). * 4.7.1, delete “Preproduction“ and substitute “First article“. * 4.7.1.1, line 1, delete “preproduction“ and substitute “first article“. PAGE 9 * 5.1, delete in its entirety and substitute: “5.1 First article pack. Th

26、e contractor shall furnish a first article pack for examination within the time frame specified (see 6.2) to prove prior to starting production packaging the applied preservation, packing and marking comply with packaging requirements of this specification. those specified in section 4 and shall be

27、subject to surveillance and approval by the Government (see 6.3). The first article pack may be prepared utilizing either the first article kit or a production mounting kit. article kit is utilized, any preservation and packing shall be removed by the contractor at no expense to the Government, when

28、 requested by the Government, to facilitate comparison between the first article kit and production kit.“ Examinations shall be When the first PAGE 10 6.2 delete in its entirety and substitute: * “6.2 Ordering data. 6.2.1 Acquisition requirements. Acquisition documents should specify the following:

29、a. Title, number, and date of this specification. b. c. d. Date of issue of DODISS applicable to this contract and exceptions thereto (see 2.1.1). Time frame required for submission of initial production model (see 3.3). Government and contractor testing responsibilities (see 4.1). *. 5 Licensed by

30、Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-5300 (2) LO 7797706 0334543 3 i l MIL-M-53008(M) AMENDMENT 2 * e. Color required when other than specified (see 3.7). * f. Time frame when camouflage pattern data (see

31、 3.12) is required. g. Data requirements (see 3.9.2.1 and 4.1). h. Test requirements (see 4.4.3). i. j. Time frame required for submission of first article pack (see 5.1). Degree of packing required (see 5.3). * 6.2.2 Data requirements. When this specification is used in an acquisition which incorpo

32、rates a DD Form 1423, contract data requirements list (CDRL), the data requirements identified below shall be developed as specified by an approved data item description (DD Form 1664) and delivered in accordance with the approved CDRL incorporated into the contract. When the provisions of DOD FAR S

33、upplement, Para 27, Sub-Part 27.410-6 are invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with the contract or purchase order requirements. this specification is cited in the following paragraphs: Deliverable data required by Para

34、graph No. Data Requirements Applicable DID No. (a) 3.12 Camouflage Pat tern UDI-V-24003/M Photos (see figure 1) (b) 3.12 Camouflage Pattern DI-M-30420/M Illustrations (see figure 2) * 6.3, lines 1, 2 and 3, delete “preproduction“ and substitute “first article“. Add new paragraphs: 6.5 Government-fur

35、nished property. The contracting officer should arrange to 11 furnish the property listed in 3.12. * 6.6 Lubricants. MIL-STD-838, Lubrication of Military Equipment, prescribes the policy for using specification-type products wherever possible and provides specific requirements for potential use of n

36、on-standard proprietary products. MIL-STD-838 is implemented by MIL-HDBK-113, Guide for the Selection of Lubri- cants, Fluids, Preservatives and Speciality Products for Use in Ground Equipment Systems. by the US Army Belvoir Research and unless otherwise specified on the DD Form 1423. Views shall in

37、clude, but not be limited to, a front, side, and rear view. Background of photographs shall be void of unrelated objects. 10.2 Interior views shall be in sufficient quantity to show arrangement and layout of installed equipment. 10.3 Photographic prints shall show excellent detail and shall be color

38、 suitable for reproduction. D ,t,EY,.)664 FIGURE 1. Camouflage pattern photos. 8 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I r . MIL-U-53008 (2) LO = 7777906 0334546 7 MIL-M-5 300 8(ME) AMENDMENT 2 DATA

39、ITEM DESCRIPTION Technical Illustrations and Graphs -. I OLCRICTlON/PURPOSL To provide wave plotting, drafting, computations, data reduction and/or mathematical analysis in support of research projects. - _- - - Lip CL IC Li I IO U/ INTER Pl I L Al IONIHIP Mathemat jcal Services Jrojccts - _ - D PRC

40、P AMA 1 ION IU 1 RUC 1 IONS IOENTIFICATION NOIS). AGENCY NUMBER USAF i DI-M-30420/M I. APPROVAL DATE - 29 Oct 1976 - I. OFFICE OF PRIUAUY R EIPONIIOILITI AFSC I. DDC RcoutnEo I. APPROVAL LIUITATON Data will. encompass plotting, drafting and artistic creative illustrations of apparatus and devices. r

41、eprescntationc. high quality to be used for publication in technical journals and for visual aids at conferences, reviews and briefings. lhe work may include three-dimensional pictorial Complctcd reproducible art vork must be of sufficiently U.S. BOVtRNHEYl PRXNTINO OFFICE: ITIS - L03-036fZ4417 9 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-