ARMY MIL-M-63248-1977 MICRODETONATOR CLIP ASSEMBLY PARTS FOR《微雷管剪辑组装零件》.pdf

1、MIL-M-6324B 13 M 7777706 0346454 7 M - PIIL-14-63248 (AR) 7 November 1977 141 L ITARY SPEC IF I CATI ON MICRODETONATLIR CLIP ASSEMBLY PARTS FOR This specification is approved for use by the U.S. Army Armament Research aiici ilevelopnent Coimaiid and is available for use by all Departments and Agenci

2、es of the Department of Defense. 1. SCOPE 1.1 This specification contains requirements not normally covered by the drawings and provides quality assurance pro- visions for the fabrication of parts, assembly and packing for Microdetonator Clip Assembly. 2. APPLICABLE DCUI4EiJTS 2.1 Issues of document

3、s. - The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPEC IF I CAT I ON S MILITARY 14IL-A-48078 - Armunition, Standard Quality Assurance Provisions, General Specification For STAI

4、JDAWS MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes D1UWINGS (See 6 4) U. S. ARTU ARTjWdENT RESEARCH AND DEVELOP.?4EIJT COI!U4AND 9326705 - Microdetonator Clip Assembly 9326743 - Container for Microdetonator Clip Assembly FSC: 1375 Beneficial commenta (recommendations, ad

5、ditions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, US Army Armament Research and Development Command, Attn. DRDAR-QA, Dover, New Jersey 07801 by using the self-addressed standardization Document Improvement Froposal (DD Form 1

6、426) appearing at the end of this document or by letter. - - . .: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-fl-6324 13 7777706 03461155 O W MIL-M-63248 (AR) 3. F3QUIREI4ENTS 3.1 Material. - Materials shall be in accordance with the applicab

7、le drawings and specifications. 3.2 Parts. - The parts shall comply with all requirements specified on Drawing (Dwg) 9326705, all associated drawings, and with all requiremnts specified in applicable specifications. 3.3 First article inspection. - This specification contains technical provisions for

8、 first article inspection. Requirements for the submission of first article samples by the contractor shall be as specified in the contract. 3.4 Workmanship. - Ail parts and assemblies shall be fabricated and finished in a thorough, workmanlike manner. They shall be free of burrs, chips, sharp edges

9、, cracks, unblended radii, surface defects, dirt, grease, rust, corrosion products, and other foreign matter. Cleaning methods used shall not be injurious to any parts, nor shall the parts be contaminated by the cleaning agents. All marking and stamping shall be neat and sharply defined. 4. QUALITY

10、ASSUFtAIVCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions. - Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 shall apply and - - are hereby made a part of this detail specification. 4.2 Classification of inspections. - The

11、following types of inspection shall be conducted on this item: a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection. - 4.3.1 Submission. - The contractor shall submit a first article as designated by the Contracting Officer for evaluation in accordance with the

12、provisions of 4.3.2. The first article sample shall consist of the following items in sample quantities as indicated. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-U-63248 13 W 7777906 0346456 2 - S/ MIL-M-6 3 248 (AR) Part Description Drawin

13、gs Quantity Clip, Microdetonator 9326703 Shunt, Microdetonator 9326704 Microdetonator Clip Assembly 9326705 25 25 25 4.3.2 Inspections to be performed. - See MIL-A-48078 and Table I herein. 4.3.3 Rejection. - See MIL-A-48078. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

14、hout license from IHS-,-,-MIL-M-63248 13 = 9977706 0346457 4 M h In c, E W E O Q o U E E m h F P u) u) P o L 5 .r F - 9 m E O c Q) -0 O L o E - v llY Lo Cu N Cu - 3 3 - 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-63248 (AR) 4. QUALITY CON

15、FON4AdCE INSPECTIOW 4.4.1 Inspection lot formation. - Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination. - See MIL-A-43078. a. Sampling Plans. - Unless otherwise specified in the Classification of Defects and Test tables, sampling plans for major aiid m

16、inordefects shall be in accordance with MIL-STD-105, Inspection Level II. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-F 7 IL O I- k I Lo CUNNNNTU &NO CUNNNN mmmmm mmmmmm mmv! . . . . . . . . . . ui c w y. Y P L h L v) cl a: c U O (II L r c c E:

17、 c .I- al C x cn I- v c O a E U L L S C. m cl O c - .- Ei c I O z c I-W .r,% mw Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-P b P. li I v (21 S O c1 Q U O L U .r z L P W != .r ic W U aJ E 0 ZZ .- uuu L O 3 L O C c cc C / Provided by IHSNot for Re

18、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-63248 13 W 9999906 0346462 W MIL-M-63248 (AR) 4.4.3 Testing. - Testing is described in the First Article and Quality Conformance Inspection Tables. 4.4.4 Inspection equipment. - The inspection equipment required to perfor

19、m the examinations and tests prescribed herein is described in the Paragraph Reference/Inspection Method column in the tables starting with Paragraph 4.4.2.1. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 5 of MIL-A-48

20、078 and 6.3 herein. 4.5 Test methods and procedures. - 4.5.1 Dimensional control of stamped parts. - In place of the normal sampling associated with the Classifica.tion of Defects, and with the approval of the Contracting Officer, a sample of at least ten (10) parts shall be dimensionally inspected

21、to qualify the tool used in the stamping process for use in pro- duction. In addition, a random sample of five (5) parts shall be selected from the last portion of each hours pro- duction for dimensional inspection as a control of the tool during production. . If any defective parts are found during

22、 qualification of the tool, the tool producing the defective part shall not be used in production. If any defective parts are found when inspection is per- formed for control of the tool, the tool producing the defective part shall be removed from production. Further, that portion of production sinc

23、e the last tool control check shall be re- turned to the contractor for corrective action. may, after reworking, be returned to production providing they pass the qualification test above. The contractor may request a change of inspection frequency providing he presents objective evidence to the Con

24、tracting Officer to substantiate the request. All tools removed from production because of some fault, 5. PACKAGING 5.1 Preservation and packaging. - 5.1.1 Level B. - The microdetonator clip assembly shall be preserved and packaged in accordance with Dwg. 9326743. 5.2 Packing 5.2.1 Level B. - The mi

25、crodetonator clip assembly, preserved and packaged as specified in 5.1.1, shall be packed for shipment in accordance with Dwg. 9326743. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-14- G 3 2 4 8 (AR) 5.3 Marking. - Marking of the carton shal

26、l comply with Dwg. 9326743. 5.4 Shipping. - When components from more than one lot are shipped at one time, as a carload, each lot shall be kept separate and, the division between lots clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Intended use. - Not applicable. 6.2 Orderi

27、ng data. - See MIL-A-42078. 6.3 Submission of inspection equipment designs for approval. - Submit equipment designs as required to Commander, ATTN: DRDAR-QAA-I, ARRADCOM, Dover, New Jersey 07801. Re- quest letter of submittal state contractor, contract number, specification number, item nomenclature

28、 and classification of defects or test paragraph. . 6.4 Drawings. - Drawings listed in Section 2 of this specification under the heading U.S. Army Armament Research and Development Command (ARRADCOI4) may also include drawings pre- pared by, and identified as, Edgewood Arsenal, Frankford Arsenal, Ro

29、ck Island Arsenal or Picatinny ARsenal drawings. Technical data originally prepared by these activities is now under the cognizance -of ARRADCOM. Custodian: Preparing Activity: %, Army-AR Amy-AR Project Number: 1375-A-208 f7U.S. GOVERNMENT PRINTING OFFICE: 1978 - 703-122/1103 10 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-