ARMY MIL-M-70780-1988 MINE ANTI-PERSONNEL M86 ARMING ASSEMBLY FOR《杀伤地雷M86装备的安装》.pdf

1、_ MIL-U-70780 13 7777706 0357522 O Beneficial comments (recommendations, additions. deletions) and any pertinent data which may be of use in Improving this document should be addressed to: Commander, U.S. Army Armament,Munitions and Chemical Command, Attn. AMSMC-QA, Picatinny Arsenal, New Jersey 078

2、06-500 by using the self-addressed Standardiza- tion Document Improvement Proposal (DD Form 1426) appearing at the end of this dwument or by letter. MIL-M-70780 (AR) 10 JULY 1988 . MILITARY SPECIFICATION MINE, ANTI-PERSONNEL: M86 AWING ASSEMBLY FOR This specification is approved for use within the U

3、.S. Army Armament Munitions and Chemical Command, and is available foi use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the Hardware for Arming 2. APPLICABLE DOCUMENTS. 2.1 Government documents. . Assembly for the Mine, Anti-Personnel M8

4、6. rn 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and

5、 Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For FEDERAL QQ-P- 41 6 - Plating, Cadmium (Electrodeposited) STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and

6、Tables for Inspection by Attributes , AMSC N/A FSC 1345 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. z 7 THIS DOCUMENT CONTAINS 0 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-70780 13 W 997990b 035

7、7523 2 W MIL-M-707 80 (AR) 2.1.2 Other government - documents, drawings, and publications. ._._I The following other Government documents, drawings, specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. . and publications form a part of th

8、is specification to the extent DRAWINGS U.S. ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER 12579590 125795131 9366659 12579586 12579594 9366650 12579597 12579589 12579600 12 5.7 9 583 12579584 12579582 NAS163 5-OGLL3 12579587 12579588 12579595 12579585 mm5ao - Clip, Safety - Ring, Hooku

9、p - Ring, Pull - Clip, Shorting Bar - Hook, Shorting Bar - Insulator, Mounting Plate - Ring, Coated - Ring, Retaining, External - Pin, Safety - Washer, Safety Pin - Lever, Arming - Stiffener, Plate - Plate, Mounting - Cam - Screw, Pan Head - Sleeve, Lever - Rivet, Lever - Arming Assembly - PDM (Copi

10、es of specifications, standards, handbooks, drawings, publications and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 - 2 E? 8 a .rl ci c VI r O O x

11、 h Ln rl c1 * e e e - L, O rl dp OrPdpdP dP dp co O00 o o oo u* * * * O a* .e. . . 00 O00 o o d ar 5 a ctn I= )-i aE: a, sa Y mu xn Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-N-70780 13 M 7777906 0357546 3 FI 25 t ri z # M . a a, d .d ICI c

12、ram c c-d a %ha, ao c a, rn - al dOOa, u o ad. u pi .rl Lc Li L-i O O pi o 25 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-U-70780 13 779770b 03575Ll7 5 a a, Li. m O u u, C b I .d ir% c o Li m u 4-1 rl .d cd Li ? u o) 3 a, V -4 .d .d 01 W M .m

13、 . dp O rl . a a, r: .rl ICI a, a a, C zo a a, m O U O 5 Li O Pi dl .d O1 u Od CO .rl cv c n O h Ln L 26 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-il-70780 13 W 7777706 0357548 7 W . z o E-i u w pi tD z H w u H 3 u k P H 2 a c O .d c1 W m m

14、 . OW I O I 0 I rl 0 a, G .d w a, W a, c g- rl 14 2 ?Y rl Li aJ Dl O Li 3 .r( .r( ci rd O u 14 .rl c (Il c Y Li O 3 8 O pi Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-M-70780 13 779770b 0357599 7 W c F r: k C a r C r I r I c: E I- r VI w c

15、d r Y w n 8 Z O U F - a 3 u rl m 3 rn .rl 3 I+ m 3 rn 3 -A oo dpdp dp o O0 OW O -Y *-Y O O a I4 Q oc rl U a, c rl CI a, o a, E: 2 Me O0 drl u Od CO .rl hl 28 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b NIL-M-70780 13 m 977970b 0357550 5 m i MIL

16、-M-70780 (AR) 4.4.3 Testing. Testing is described in the First Article and Quality Conformance Inspection Tables. 4.4.4 Inspection equipment. The inspection equipment required to perform the examinations and tests prescribed herein is described in the Paragraph Reference/Inspect?on Method column in

17、the tables starting with Paragrash 4.4.2.1. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See MIL-A-48078. 4.5 Methods of inspection. 4.5.1 Dimensional control of stamped parts. In place of the normal sampling associated with the

18、Classification of Defects, and with the asproval of the Contracting Officer, a sample of at least ten (10) parts shall be dimensionally inspected to qualify the tool used in the stamping process for use in production. In addition, a random sample of five (5) parts shall be selected from the last por

19、tion of each hours production for dimensional inspection as a control of the tool during production. If any defective parts are found during qualification of the tool, the tool producing the defezt.ive part shall not be used in production. If any defective parts are found when inspection is performe

20、d for control of the tool, the tool 2roducing the defective part shall be removed from production, Further, that portion of production since the last tool control check shall be returned to the contractor for corrective action. All toois removed from production because of some fault, may, after rewo

21、rking, be returned to production providing they pass the qualification test above. The contractor may request a change of inspection frequency providing he presents objective evidence to the Contracting Officer to substantiate the request. each part number shall be selected from each lot in accordan

22、ce with the lot formation provisions of specification QQ-P-416. The test shall be tested as specified in ASTM B 117-73. The parts shall be tested ,for the duration specified on the applicable drawing. At the end of the required time, the parts shall be examined for evidence of white corrosion produc

23、ts (See Section 3 4.5.2 Salt spray test of protective finish. Five parts of of QQ-P-416). If any part shows any.evidence of corrosion the lot This is a destructive test. Parts so tested shall not be represented by the sample shall be rejected. returned to the lot. 29 Provided by IHSNot for ResaleNo

24、reproduction or networking permitted without license from IHS-,-,-MIL-M-70780 33 9797706 0357553 7 MIL-M-7 O 7 8 O (AR) .5. PACKAGING 5.1 Preservation and packaging. - 5.1.1 Level B. The hardware shall be preserved and packaged in accordance with MIL-STD-1169. Each package shall contain only one par

25、t number. 5.2 Packing. O 5.2.1 - Level B. The hardware, preserved and packaged as specified in 5.1.1, shall be packed for shipment in accordance with MIL-STD-1169. Each pack shall contain only one part number, * 5.3 Marking_. Marking of the carton shall comply with MIL-sTD-. 5.4 Shipping. When compo

26、nents from more than one lot are shipped at one time, each lot shall be kept seperate, and the division between lots clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Intended use. The components covered by the specification are intended for use on the M86 - Mine, Anti-Personn

27、el. 6.2 Submission of designs for approval. See MIL-A-48078. submit equipment designs, as required, to Commander, Picatinny Arsenal, ATTN: AMSMC-QAT-M (D), Picatinny Arsenal, NJ 07806-5000. This address shall be specified on the Contract Data Requirements List, DD Form 1423 in the Contract. Unless o

28、therwise specified, DI-R-1714 will apply., 6.3 Submission of results of contractor-conducted examinations and tests. Data shall be submitted in accordance with data item DI-R-1721 on the DD Form 1423 for the contract. 6.4 Distribution of ammunition data cards, inspection and test results, process co

29、ntrols. Distribution of ammunition data cards, inspection and test results, process controls shall be sent to: Commander Picatinny Arsenal, NJ 07806-5000 ARDEC ATTN: AMSMC-QAT-M (D) Cus tod ian : Army-AR 30 4. Preparing Activity: Army-AR (Project: 1345-A513) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-